Greg,
I think I meet the similar problem on my ARM946E-S board. My toolchain
is gcc 3.4.4 and uClinux is the uClinux-dist-20070130 from uclinux
official website.
My question is about console setup. What should I do to make console
work for userland applications? I prefer using "core
applications->enable console shell" .
Thanks in advance.
Shuanglin
Greg Ungerer wrote:
Hi Srikanth,
Srikanth Chavali wrote:
Hi Greg,
Just figured out that ADI Engineering is using uClinux-dist.
What version?
I looks like a console setup problem...
Regards
Greg
srikanth chavali
On 5/10/07, *Greg Ungerer* < [EMAIL PROTECTED]
<mailto:[EMAIL PROTECTED]>> wrote:
Hi Srikanthn
Srikanth Chavali wrote:
> I compiled ( 2.6.x kernel) and loaded the zImage and
ramdisk.gz on my
> board with IXP425. The board seems to be in the process of
loading the
> kernel when it stops after the messages shown below.
Are you using the uClinux-dist, or something else?
If yes, what version?
Regards
Greg
> I googled and found people facing similar issues. I ensured that
i had
> CONFIG_FPE_NWFPE=y and CONFIG_FPE_FASTFPE is not set in my kernel
configs.
>
> Any help would be greatly appreciated.
>
> Regards,
>
> srikanth chavali
>
> Attached are the messages:
>
> Intel/Sharp Extended Query Table at 0x010A
> Intel/Sharp Extended Query Table at 0x010A
> Intel/Sharp Extended Query Table at 0x010A
> Intel/Sharp Extended Query Table at 0x010A
> Using buffer write method
> cfi_cmdset_0001: Erase suspend on write enabled
> Searching for RedBoot partition table in IXP4XX-Flash.0 at offset
0xfe0000
> 3 RedBoot partitions found on MTD device IXP4XX-Flash.0
> Creating 3 MTD partitions on "IXP4XX-Flash.0":
> 0x00000000-0x00060000 : "RedBoot"
> 0x00fe0000-0x00fff000 : "FIS directory"
> mtd: partition "FIS directory" doesn't end on an erase block
-- force
> read-only
> 0x00fff000-0x01000000 : "RedBoot config"
> mtd: partition "RedBoot config" doesn't start on an erase block
boundary
> -- forc
> e read-only
> mice: PS/2 mouse device common for all mice
> i2c /dev entries driver
> TCP bic registered
> NET: Registered protocol family 1
> NET: Registered protocol family 17
> RAMDISK: Compressed image found at block 0
> VFS: Mounted root (ext2 filesystem) readonly.
> Freeing init memory: 96K
<------------------------------------------
> Nothing seems to happen after this
> although it does'nt look like the system is frozen.
>
> --
> srikanth chavali
>
>
>
------------------------------------------------------------------------
>
> _______________________________________________
> uClinux-dev mailing list
> uClinux-dev@uclinux.org <mailto:uClinux-dev@uclinux.org>
> http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
<http://mailman.uclinux.org/mailman/listinfo/uclinux-dev>
> This message was resent by uclinux-dev@uclinux.org
<mailto:uclinux-dev@uclinux.org>
> To unsubscribe see:
> http://mailman.uclinux.org/mailman/options/uclinux-dev
<http://mailman.uclinux.org/mailman/options/uclinux-dev>
--
------------------------------------------------------------------------
Greg Ungerer -- Chief Software Dude EMAIL:
[EMAIL PROTECTED] <mailto:[EMAIL PROTECTED]>
Secure Computing Corporation PHONE: +61 7 3435
2888
825 Stanley St, FAX: +61 7
3891 3630
Woolloongabba, QLD, 4102, Australia WEB:
http://www.SnapGear.com
_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org <mailto:uClinux-dev@uclinux.org>
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
<http://mailman.uclinux.org/mailman/listinfo/uclinux-dev>
This message was resent by uclinux-dev@uclinux.org
<mailto:uclinux-dev@uclinux.org>
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev
<http://mailman.uclinux.org/mailman/options/uclinux-dev>
--
srikanth chavali
------------------------------------------------------------------------
_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
This message was resent by uclinux-dev@uclinux.org
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev
_______________________________________________
uClinux-dev mailing list
uClinux-dev@uclinux.org
http://mailman.uclinux.org/mailman/listinfo/uclinux-dev
This message was resent by uclinux-dev@uclinux.org
To unsubscribe see:
http://mailman.uclinux.org/mailman/options/uclinux-dev
