hi maxim,i do have some specific question, at the asterisk connector config
below[asterisk-connector]
Description = MySQL connection to 'openmeetings' database
Driver = MySQL
Database = openmeetings
Server = localhost
USER = root
PASSWORD =
Port = 3306
Socket = /var/run/mysqld/mysqld.sock
where datbase name = openmeetings, my databse name for openmeeting version
3.06 is open306, is the databsea name were used in the
/opt/red5/webapps/openmeetings/WEB-INF/classes/openmeetings-applicationContext.xml
<constructor-arg><value>127.0.0.1</value></constructor-arg>
<constructor-arg><value>5038</value></constructor-arg>
<constructor-arg><value>openmeetings</value></constructor-arg>
<constructor-arg><value>12345</value></constructor-arg> --> as the colored
part of the code.secondly, asterisk –rx “database show” would be ran after the
dia plan has been configure as in the example. thanks
On Saturday, September 5, 2015 11:40 PM, Maxim Solodovnik
<[email protected]> wrote:
To be fair, I don't remember :(((I performed configuration long ago, but I did
exactly what is written on the configuration page, step by step :))I can check
existing installation if you have any particulal question :)
On Fri, Sep 4, 2015 at 8:24 PM, Awotipe Oluwaseun <[email protected]>
wrote:
Thanks ,
One last question, when is the appropriate time to run asterisk -rx "database
show", after all config is done or before diaplan configuration is done.
Thanks once againoluwaseunOn Sep 4, 2015 8:46 AM, Maxim Solodovnik
<[email protected]> wrote:
These steps:
Update Openmeetings with creadentials for Asterisk manager. Modify
/opt/red5/webapps/openmeetings/WEB-INF/classes/openmeetings-applicationContext.xml
find <bean id="sipDao" class="org.apache.openmeetings.db.dao.room.SipDao">
uncomment its parameters and set it to your custom values.IMPORTANT: this step
should be done BEFORE system install/restore otherwise all SIP related room
information will be lost
On Fri, Sep 4, 2015 at 7:43 PM, Awotipe Oluwaseun <[email protected]>
wrote:
Please can you suggest which file on OM that I need to reconfigure, I follow
the instructions as it was writing only the database name changed.
oluwaseunOn Sep 3, 2015 9:49 PM, Maxim Solodovnik <[email protected]> wrote:
Maybe Asterisk connection on OM side wasn't properly configured?
On Fri, Sep 4, 2015 at 4:01 AM, awotipe oluwaseun <[email protected]>
wrote:
thanks smith for your last comment and guildiance, i have some more othaer
questions from the instruction at Modify
/etc/asterisk/extensions.conf
;
*****************************************************; The below dial plan is
used to dial into a Openmeetings Conference room
; The first line DB_EXISTS(openmeetings/room/ does not belong to the
openmeetings application but is the name of astDB containing the astDB
family/key pair and values
; To Check if your astDB has been created do the following in a terminal window
type the following:
; asterisk –rx “database show”
; If you do not receive an output with that resembles openmeetings/rooms/400##
where “##” will equal the extension assigned when you created your room
; If you do not receive the above output check your parameters in
/opt/red5/webapps/openmeetings/WEB-INF/classes/openmeetings-applicationContext.xml
; Go back into the Administrator Panel and remove the PIN number in each room
save the record with no PIN number and then re-enter the pin again resave the
record.; *****************************************************I ran the command
asterisk –rx “database show” before and after iput the the values of the
room state below the screen shot above, i got same result as below
Privilege escalation protection disabled!
See https://wiki.asterisk.org/wiki/x/1gKfAQ for
more details.
/dundi/secret :
oe+jF4tGLSeIhzY4y6FEOg==;KzAQOOPStj0IOXZW8oMQcg==
/dundi/secretexpiry : 1441320143
2 results found. which is different from what is
expected, i am runing asterisk 11.70.Any is there anything that i am doing
wrongly here.thanks
On Thursday, September 3, 2015 10:54 AM, Pierre Smits
<[email protected]> wrote:
I wouldn't recommend it for production purposes. There it is best to have
separate setups for OpenMeetings, the RDBMS and the SIP server. But for
evaluation purposes an all-in-one box could suffice.
As the document states in the section below OEM-prelim-ScreenShot-product the
following line determines the location of the server:
Server = localhost
Changing that to the ip address (or fqdn) of the mysql server will make it use
the external rdbms.
Best regards,
Pierre Smits
ORRTIZ.COMServices & Solutions for Cloud-Based Manufacturing,
ProfessionalServices and Retail & Tradehttp://www.orrtiz.com
On Thu, Sep 3, 2015 at 4:11 PM, awotipe oluwaseun <[email protected]>
wrote:
hi all, i am trying to integrate sip with my current openmeetings, i got
confused the some steps from the instruction (
http://openmeetings.apache.org/red5sip-integration_3.0.html ),. my question is
do i have to setup asterisk server separately or it could be all inone box with
openmeeting server, does the Asterisk use exsiting database on openmeeting
server, if so how do i connect it to the databse.please forgive me for asking a
lame man questions.thanks
--
WBR
Maxim aka solomax
--
WBR
Maxim aka solomax
--
WBR
Maxim aka solomax
