Hello Horace, The instructions were not changed for a long time, if you have anything to add/change please let me know :) contributions are highly appreciated :)
On Tue, Sep 8, 2015 at 1:51 AM, Horace Miles < [email protected]> wrote: > Maxim, > > Have there been any updates to the SIP integration since the 3.0 > instructions were put out. i.e. any way to kick users that are connected > via sip etc? > > > > *From:* Maxim Solodovnik [mailto:[email protected]] > *Sent:* Saturday, September 05, 2015 9:40 PM > *To:* Awotipe Oluwaseun > *Cc:* Openmeetings user-list > *Subject:* Re: Sip integration > > > > To be fair, I don't remember :((( > > I performed configuration long ago, but I did exactly what is written on > the configuration page, step by step :)) > > I can check existing installation if you have any particulal question :) > > > > On Fri, Sep 4, 2015 at 8:24 PM, Awotipe Oluwaseun < > [email protected]> wrote: > > Thanks , > One last question, when is the appropriate time to run asterisk -rx > "database show", after all config is done or before diaplan configuration > is done. > Thanks once again > > oluwaseun > > On Sep 4, 2015 8:46 AM, Maxim Solodovnik <[email protected]> wrote: > > These steps: > > > > > > Update Openmeetings with creadentials for Asterisk manager. Modify > /opt/red5/webapps/openmeetings/WEB-INF/classes/openmeetings-applicationContext.xml > find *<bean id="sipDao" > class="org.apache.openmeetings.db.dao.room.SipDao">* uncomment its > parameters and set it to your custom values. > > IMPORTANT: this step should be done *BEFORE* system install/restore > otherwise all SIP related room information will be lost > > > > > > On Fri, Sep 4, 2015 at 7:43 PM, Awotipe Oluwaseun < > [email protected]> wrote: > > Please can you suggest which file on OM that I need to reconfigure, I > follow the instructions as it was writing only the database name changed. > > oluwaseun > > On Sep 3, 2015 9:49 PM, Maxim Solodovnik <[email protected]> wrote: > > Maybe Asterisk connection on OM side wasn't properly configured? > > > > On Fri, Sep 4, 2015 at 4:01 AM, awotipe oluwaseun < > [email protected]> wrote: > > thanks smith for your last comment and guildiance, i have some more othaer > questions from the instruction at > > > > Modify /etc/asterisk/extensions.conf > > ; > ***************************************************** > > ; The below dial plan is used to dial into a Openmeetings Conference room > > ; The first line DB_EXISTS(openmeetings/room/ does not belong to the > openmeetings application but is the name of astDB containing the astDB > family/key pair and values > > ; To Check if your astDB has been created do the following in a terminal > window type the following: > > ; asterisk –rx “database show” > > ; If you do not receive an output with that resembles > openmeetings/rooms/400## where “##” will equal the extension assigned when > you created your room > > ; If you do not receive the above output check your parameters in > /opt/red5/webapps/openmeetings/WEB-INF/classes/openmeetings-applicationContext.xml > > ; Go back into the Administrator Panel and remove the PIN number in each room > save the record with no PIN number and then re-enter the pin again resave the > record.; ***************************************************** > > I ran the command asterisk –rx “database show” before and after iput > the the values of the room state below the screen shot above, i got same > result as below > > > > Privilege escalation protection disabled! > > See https://wiki.asterisk.org/wiki/x/1gKfAQ for > more details. > > /dundi/secret : > oe+jF4tGLSeIhzY4y6FEOg==;KzAQOOPStj0IOXZW8oMQcg== > > /dundi/secretexpiry : 1441320143 > > 2 results found. > > which is different from what is expected, i am runing asterisk 11.70. > > Any is there anything that i am doing wrongly here. > > thanks > > > > > > On Thursday, September 3, 2015 10:54 AM, Pierre Smits < > [email protected]> wrote: > > > > I wouldn't recommend it for production purposes. There it is best to have > separate setups for OpenMeetings, the RDBMS and the SIP server. But for > evaluation purposes an all-in-one box could suffice. > > > > As the document states in the section below OEM-prelim-ScreenShot-product > the following line determines the location of the server: > > > > Server = localhost > > Changing that to the ip address (or fqdn) of the mysql server will make it > use the external rdbms. > > > > Best regards, > > > Pierre Smits > > > > *ORRTIZ.COM <http://www.orrtiz.com/>* > > Services & Solutions for Cloud- > > Based Manufacturing, Professional > > Services and Retail & Trade > > http://www.orrtiz.com > > > > On Thu, Sep 3, 2015 at 4:11 PM, awotipe oluwaseun < > [email protected]> wrote: > > hi all, > > i am trying to integrate sip with my current openmeetings, i got confused > the some steps from the instruction ( > http://openmeetings.apache.org/red5sip-integration_3.0.html ),. > > my question is do i have to setup asterisk server separately or it could > be all inone box with openmeeting server, does the Asterisk use exsiting > database on openmeeting server, if so how do i connect it to the databse. > > please forgive me for asking a lame man questions. > > thanks > > > > > > > > > > -- > > WBR > Maxim aka solomax > > > > > > -- > > WBR > Maxim aka solomax > > > > > > -- > > WBR > Maxim aka solomax > > > ------------------------------ > [image: Avast logo] <https://www.avast.com/antivirus> > > This email has been checked for viruses by Avast antivirus software. > www.avast.com <https://www.avast.com/antivirus> > > -- WBR Maxim aka solomax
