so NAT and loadbalancers are not possible if we use security group? so it meanse there will be no internal and external IPs for VMs. is it correct?
On Wed, Nov 26, 2014 at 3:14 PM, Jayapal Reddy Uradi < jayapalreddy.ur...@citrix.com> wrote: > For SG networks there is no public network. > We configure public ips for the guest network. > > -Jayapal > > On 26-Nov-2014, at 12:00 PM, Tejas Sheth <tshet...@gmail.com> > wrote: > > > Hello, > > > > I have made the bridge configuration, but when i am selecting advance > > zone. it is not showing public network configuration. only guest and > > management is availabel. also internal CIDR ip configuration is also not > > available. > > i think it is cinverting to basic zone if we select security group and > > xenserver as hypervisor. > > > > Thanks > > Tejas > > > > On Tue, Nov 25, 2014 at 9:16 PM, Jayapal Reddy Uradi < > > jayapalreddy.ur...@citrix.com> wrote: > > > >> > >> For 6.2 you no need to install CSP. My typo mistake in last mail. > >> sysctl.conf is fine. > >> > >> > >> Thanks, > >> Jayapal > >> > >> On 25-Nov-2014, at 8:45 PM, Tejas Sheth <tshet...@gmail.com> > >> wrote: > >> > >>> Thanks, > >>> > >>> So can i take it as confirmation and proceed with only following bridge > >>> configuration in xenserver 6.2? > >>> > >>> # xe-switch-network-backend bridge > >>> > >>> # vi /etc/sysctl.conf > >>> net.bridge.bridge-nf-call-iptables = 1 > >>> net.bridge.bridge-nf-call-ip6tables = 0 > >>> net.bridge.bridge-nf-call-arptables = 1 > >>> > >>> # sysctl -p /etc/sysctl.conf > >>> > >>> Require confirmation for sysctl.cnf configuration part. > >>> > >>> Thanks and regards, > >>> Tejas > >>> > >>> On Tue, Nov 25, 2014 at 8:31 PM, Vadim Kimlaychuk < > >> vadim.kimlayc...@elion.ee > >>>> wrote: > >>> > >>>> XenServer does not need any package to be expicitly installed. When > you > >>>> add host to CS it copies some files to the host itself and you don't > >> need > >>>> to bother about them usually. > >>>> > >>>> Vadim. > >>>> > >>>> -----Original Message----- > >>>> From: Tejas Sheth [mailto:tshet...@gmail.com] > >>>> Sent: Tuesday, November 25, 2014 4:52 PM > >>>> To: users@cloudstack.apache.org > >>>> Subject: security group and xenserver query > >>>> > >>>> Hello Jayapal, > >>>> > >>>> Thanks for reply, I have understood the bridge configuration part but > >>>> can you clarify CSP package part. > >>>> > >>>> if CSP package comes with xenserver 6.2 then do we need to install it > >>>> explicitly? > >>>> > >>>> It would be really helpful if you can send link to install CSP in > >>>> xenserver 6.2 because CS 4.3 document do not have description for > >> xenserver > >>>> 6.2 CSP installation. > >>>> ---------------------------------------------------------------- > >>>> Hi Tejas, > >>>> > >>>> The network mode set to 'bridge' mode. > >>>> #xe-switch-network-backend bridge > >>>> > >>>> I think Xenserver 6.2 comes with the CSP package, so you need to > install > >>>> it explicitly. > >>>> > >>>> > >>>> Thanks, > >>>> Jayapal > >>>> > >>>> > >>>> On 25-Nov-2014, at 4:47 PM, Tejas Sheth <tshet...@gmail.com> > >>>> wrote: > >>>> > >>>>> Hello, > >>>>> > >>>>> We are configuring advanced zone in cloudstack 4.3 in xenserver 6.2. > >>>>> we want to configure security group in advance zone. do we have to do > >>>>> any special configuration in xenserver 6.2. > >>>>> > >>>>> xenserver has default networking configuration. > >>>>> > >>>>> Thanks and regards, > >>>>> Tejas > >>>> > >> > >> > >
