i don't see any error in this log. normally, however, you should have one more line that says "AT SMSC successfully opened." then you know that everything is ok and you can start using it.
nick On Wed, 2004-01-21 at 10:56, Aftab Rashid wrote: > Hi Nick, > > I tried it and got the following error: > > 2004-01-21 14:47:59 [0] INFO: AT2[/dev/ttyS0]: configuration shows > modemtype <siemens> > 2004-01-21 14:47:59 [0] INFO: AT2[/dev/ttyS0]: modemtype not found, revert > to autodetect > 2004-01-21 14:47:59 [0] INFO: ---------------------------------------- > 2004-01-21 14:47:59 [0] INFO: Kannel bearerbox II version cvs-20031218 > starting > 2004-01-21 14:47:59 [0] INFO: MAIN: Start-up done, entering mainloop > 2004-01-21 14:47:59 [6] INFO: AT2[/dev/ttyS0]: opening device > 2004-01-21 14:47:59 [6] INFO: AT2[/dev/ttyS0]: speed set to 9600 > 2004-01-21 14:48:01 [6] INFO: AT2[/dev/ttyS0]: Phase 2+ is supported > 2004-01-21 14:48:01 [6] INFO: AT2[/dev/ttyS0]: closing device > 2004-01-21 14:48:01 [6] INFO: AT2[/dev/ttyS0]: opening device > 2004-01-21 14:48:01 [6] INFO: AT2[/dev/ttyS0]: init device > 2004-01-21 14:48:01 [6] INFO: AT2[/dev/ttyS0]: speed set to 9600 > 2004-01-21 14:48:02 [6] INFO: AT2[/dev/ttyS0]: cannot enable hardware > handshake > 2004-01-21 14:48:02 [6] INFO: AT2[/dev/ttyS0]: Phase 2+ is supported > > > Regards, > > > Aftab > > > > > -----Original Message----- > From: Nicholas Rahn <[EMAIL PROTECTED]> > To: Aftab Rashid <[EMAIL PROTECTED]> > Cc: [EMAIL PROTECTED] > Date: Wed, 21 Jan 2004 10:10:50 +0100 > Subject: Re: Siemens Modem SMSC > > > you need to include the definition of your modem in the configuration > > file. the easiest way to do this is by adding this line to your > > configuration file: > > > > include = <path-to-kannel-source>/doc/examples/modems.conf > > > > this will include the standard modem configurations provided by kannel > > and should allow you to use your modem right away. > > > > nick > > > > > > On Wed, 2004-01-21 at 09:01, Aftab Rashid wrote: > > > Hi, > > > > > > I want to use SIEMENS M55 as SMSC. I'm getting the following > > message > > > > > > 2004-01-20 20:00:51 [0] INFO: HTTP: Opening server at port 1812. > > > 2004-01-20 20:00:51 [0] INFO: AT2[/dev/ttyS0]: configuration shows > > > modemtype <siemens> > > > 2004-01-20 20:00:51 [0] PANIC: Where are the modem definitions ?!?! > > > 2004-01-20 20:00:51 [0] PANIC: ./bearerbox [0x80a9be9] > > > 2004-01-20 20:00:51 [0] PANIC: ./bearerbox [0x805d1a2] > > > > > > and my conf file is > > > group = smsc > > > smsc = at > > > modemtype = siemens > > > device = /dev/ttyS0 > > > > > > > > > Is my mobile compatible with Kannel? If yes, what changes should be > > made > > > in the conf file to make it working. > > > > > > > > > Thanks and regards, > > > > > > > > > Aftab > > > > > > > >
