Hi
Yes, you can put several AT commands in the int string. check manual
and list for details and examples.
As for the vwdialconf init-string, note that vwdial is designed for
modem to modem (ie asyncronius) connections and the config it provides
is for that usage. That means that the init string from vwdial MIGHT
NOT WORK or have no effect for sms tranfer.
Regards
Alvaro
|-----------------------------------------------------------------------------------------------------------------|
Envíe y Reciba Datos y mensajes de Texto (SMS) hacia y desde cualquier
celular y Nextel
en el Perú, México y en mas de 180 paises. Use aplicaciones 2 vias via
SMS y GPRS online
Visitenos en www.perusms.NET www.smsglobal.com.mx y
www.pravcom.com
On Wed, Mar 10, 2010 at 8:15 PM, mpl li <[email protected]> wrote:
> Hi,
> As Nikos said I went through the modems.conf file. According to the
> init-string I found in the wvdialconf file, the modem I am using has the
> same init-string as the following group in the examples. I am not clear on
> how to include the AT+CNMI in to this. Should I replace this init-string
> with something in the form of "AT+CNMI=3,1,0,0". I would be very grateful if
> anyone help me with this.
> ________________________________
> From: Nikos Balkanas <[email protected]>
> To: mpl li <[email protected]>; [email protected]
> Sent: Mon, March 8, 2010 1:29:20 PM
> Subject: Re: Re : Kannel Configuration to set up an SMS gateway
>
> Hi,
>
> In your configuration you have only init-string without AT+CNMI. Kannel
> doesn't understand init1 or init2, just a single init-string. For examples
> how to use it see modems.conf. Wvdialconf should be fine.
>
> BR,
> Nikos
>
> ----- Original Message -----
> From: mpl li
> To: Nikos Balkanas ; [email protected]
> Sent: Monday, March 08, 2010 2:29 AM
> Subject: Re: Re : Kannel Configuration to set up an SMS gateway
> Nikos,
> Thanks a lot for your reply.
> The init-strings I have used are the 'Init1' and 'Init2' values of
> 'wvdialconf' file. And the following lines are displayed when the bearerbox
> starts.
>
> DEBUG: AT2[/dev/ttyUSB0]: --> AT+CNMI=1,2,0,1,0^M
> DEBUG: AT2[/dev/ttyUSB0]: <-- OK
>
> Can't I use the above method for finding the init-string because I am having
> trouble finding the modem manual?
> ________________________________
> From: Nikos Balkanas <[email protected]>
> To: mpl li <[email protected]>; [email protected]
> Sent: Sun, March 7, 2010 9:32:56 PM
> Subject: Re: Re : Kannel Configuration to set up an SMS gateway
>
> Hi,
>
> You need to configure AT+CNMI in your init-string. That tells your modem
> what to do with incoming SMS. It is modem specific and should consult your
> modem manual or manufacturer for it.
>
> BR,
> Nikos
>
> ----- Original Message -----
> From: mpl li
> To: [email protected]
> Sent: Sunday, March 07, 2010 5:35 PM
> Subject: Re: Re : Kannel Configuration to set up an SMS gateway
> Kidi Kidi,
> Thank you very much for your quick reply. Can you also help me with the SMS
> receiving problem.
> ________________________________
> From: Kidi Kidi <[email protected]>
> To: mpl li <[email protected]>
> Sent: Sun, March 7, 2010 7:38:42 PM
> Subject: Re : Kannel Configuration to set up an SMS gateway
>
> For me this happens whenever my sim card has run out of units. So buy Mobile
> (Prepaid Recharge) Card to try.
>
>
> ________________________________
> From : mpl li <[email protected]>
> To : [email protected]
> Sent : Dim 7 Mars 2010, 13 h 23 min 46 s
> Subject : Kannel Configuration to set up an SMS gateway
>
> Dear All,
> I am trying to configure Kannel to send and receive SMS using a Huawei E156G
> USB modem. I have 2 questions.
>
> (1) When an SMS is sent to the modem though the modem receives the SMS but
> Kannel does not detect it. nothing is recorded in the log files. Is this
> because of an error in the specified get-url, or some other error in
> configuration parameters?
>
> (2) I was able to send SMSs for a while but now even though the message
> "Accepted for Delivery" is displayed the following error occurs
>
> DEBUG: re-queing SMS not-yet-to-be resent
> DEBUG: sms_router: time to sleep 30.00 secs.
> DEBUG: AT2[/dev/ttyUSB0]: <-- +CMS ERROR: 500
> ERROR: AT2[/dev/ttyUSB0]: CMS ERROR: +CMS ERROR: 500
> ERROR: AT2[/dev/ttyUSB0]: CMS ERROR: Unknown error. -> maybe Sim storage is
> full? I'll have a look at it. (500)
> DEBUG: sms_router: gwlist_len = 1
> DEBUG: sms_router: handling message (0x97cf278 vs 0x97cf278)
> DEBUG: re-queing SMS not-yet-to-be resent
> DEBUG: sms_router: handling message (0x97cf278 vs 0x97cf278)
>
> I am very new to all this and have read the user guide and also other posts
> in the mailing list, but cannot find a solution. Any help will be greatly
> appreciated. Below is my configuration file.
>
> #---------------------------------------------
> # CORE
> #
> group = core
> admin-port = 13000
> smsbox-port = 13001
> admin-password = bar
> box-deny-ip = "*.*.*.*"
> box-allow-ip = "127.0.0.1"
> #---------------------------------------------
> # SMSC CONNECTIONS
> #
> group = smsc
> smsc = at
> modemtype=auto
> device=/dev/ttyUSB0
> my-number=+947xxxxxxxx
> port = 10000
> connect-allow-ip = 127.0.0.1
> log-level = 0
> #---------------------------------------------
> # SMSBOX SETUP
> #
> group = smsbox
> bearerbox-host = 127.0.0.1
> sendsms-port = 13013
> global-sender = +947xxxxxxxx
> log-level = 0
> #---------------------------------------------
> # SEND-SMS USERS
> #
> group = sendsms-user
> username = tester
> password = foobar
> concatenation= true
> max-messages = 10
> #---------------------------------------------
> # SERVICES
> #
> group = sms-service
> keyword-regex = .*
> catch-all = yes
> max-messages = 0
> get-url = "http://localhost/sms?phone=%p&text=%a";
>
> group = sms-service
> keyword = default
> text = "No service specified"
> #---------------------------------------------
> # MODEMS
> #
> group = modems
> id = huawei
> name = "Huawei"
> detect-string = "huawei"
> detect-string2 = "e156"
> init-string = "ATZ"
> init-string = "ATQ0 V1 E1 S0=0 &C1 &D2 +FCLASS=0"
> message-storage = "SM"
>
>
>
>
>
>
>
>
>
>
>
