I think it would be good to include this in a rbf template. This will allow for a repeatable process of image creation.
I'll post mine later today, when I'm home. Jacco On Wednesday, 21 October, 2015 11:20 CEST, Gordan Bobic <[email protected]> wrote: > It's not a kernel bug, it's a dracut bug that I was talking about. > The problem is that dracut wasn't including ehci-orion USB driver > in the initramfs. Once you figure out what the root cause of the > problem is, it is trivially fixable with the configuration option > I listed below. > > From here I should be able to follow the standard RSEL recipe: > 1) Grab a working kernel uImage, /lib/firmware, and > /lib/modules/$kernel/ > 2) Drop them into the RSEL image > 3) Make the configuration changes mentioned below (also remember to > blacklist the orion_nand driver due to the GuruPlug/DreamPlug machid > confusion issue, as loading the orion_nand driver on DreamPlug will > hang) > 4) Rebuild initramfs using dracut, and uboot it using mkimage > > And that should just work. > > For completeness and neatness, I will put together a kernel package > that can be installed using rpm and facilitate seamless kernel > upgrades. > > Another package that may require revisiting in RSEL to facilitate > seamless kernel upgrades is grubby, as this handles re-packing > vmlinux and initramfs into uImage/uInitrd. > > Gordan > > On 2015-10-21 03:09, Ioan Stan wrote: > > I would just mention that Debian Jessie runs fine on dreamplug. I can > > check the exact kernel when I get back home later today. > > > > Sent from my iPhone > > > >> On 2015/10/21, at 10:20, Gordan Bobic <[email protected]> wrote: > >> > >> Figured it out in the end. > >> > >> The problem is that ehci-orion driver went from being built into > >> the kernel in the 3.6.x kernel on F18, to it being built as a > >> module. But - dracut didn't figure out that the ehci-orion > >> driver is vital for the usb-storage driver to find anything. > >> > >> Solution is to: > >> > >> 1) add > >> add_drivers+="ehci-orion" > >> to /etc/dracut.conf > >> > >> 2) Rebuild the initramfs: > >> dracut -f -v /boot/initramfs-3.10.90-kirkwood.img 3.10.90-kirkwood > >> (adjust for your kernel name and version) > >> > >> 3) Make uInitrd from the initramfs: > >> mkimage -A arm -O linux -T ramdisk -C none -a 0 -e 0 -n initramfs -d > >> /boot/initramfs-3.10.90-kirkwood.img /boot/uInitrd > >> (make sure your uImage matches the kernel you are building the uInitrd > >> for) > >> > >> Then it all boots fine. > >> > >> So, now that the part of working around bugs in Fedora is done, > >> I might actually be able to get somewhere with getting RedSleeve > >> to work on this thing... > >> > >> Best of all, the mainline 3.10.90 kernel seems to just work and > >> support all the hardware. And firmware auto-loading works, too. > >> > >> The question now is - do we try to stick with 3.10.x LT kernel > >> for as much hardware as possible, since that is sort of almost > >> similar to what EL7 ships (don't get me started on the upstream > >> kernel patches)? Or do we perhaps skip to the the currently > >> latest LT kernel series (3.18.x)? In theory, later kernels might > >> allow supporting more devices with a single kernel code base > >> (only different configs), rather than having 3.10 kernels for > >> some well supported SoCs like the Kirkwood, and having to > >> use later LT kernels for other things anyway. > >> > >> I can see the pros and cons either way, but I am leaning toward > >> jumping up to 3.18.x mainline LT kernels. Any opinions on this > >> from anyone here? > >> > >> Gordan > >> > >> > >> > >>> On 2015-10-20 10:37, Gordan Bobic wrote: > >>> I left the latest vanilla 3.10.90 kernel building this morning. I'm > >>> hoping to try it tonight. Fingers crossed that will just work. If the > >>> firmware loading is still broken (it is also broken on F18 with their > >>> 3.6.10 kernel) the only workaround I am aware of is to build the > >>> firmware blobs into the kernel binary. I had to do this with the > >>> 3.4 kernel for the Samsung Exynos Chromebook. > >>> Gordan > >>>> On 2015-10-19 22:59, ioan stan wrote: > >>>> Thank you, Gordon. > >>>>> On Oct 20, 2015, at 05:02, Gordan Bobic <[email protected]> > >>>>> wrote: > >>>>> I'm now looking into getting DreamPlugs running, and I've > >>>>> hit the same problem. The problem seems to be particularly > >>>>> related to the 3.10.14 kernel shipping with Fedora, in that > >>>>> it's usb-storage driver is broken on the DreamPlug - it never > >>>>> detects any USB storage devices. > >>>>> The 3.6.10 kernel from the original F18 ARM release works > >>>>> fine, however. > >>>>> Additionally, I updated the u-boot on my DP to > >>>>> 2014.10+dfsg1-5, and that version requires machid to be > >>>>> set to the GuruPlug's ID (annoyingly): > >>>>> machid=0xa63 > >>>>> Presumably the old 2011 firmware had this ID in bdinfo, and > >>>>> the 3.6 and 3.10 kernels aren't new enough to recognise the > >>>>> proper DP machid. > >>>>> Of course, all sorts of other things are broken in the F18 > >>>>> standard image as well (firmware loading fails for the WiFi > >>>>> module, courtesy of systemd removing support for udev firmware > >>>>> loader helpers, and the kernel's module loader being broken > >>>>> until more recent kernels). > >>>>> Gordan > >>>>>> On 2015-09-28 15:01, Gordan Bobic wrote: > >>>>>> It looks like your initramfs doesn't include the USB disk driver. > >>>>>> The device nodes aren't there. > >>>>>> Gordan > >>>>>>> On 2015-09-28 14:46, ioan stan wrote: > >>>>>>> Please see below. > >>>>>>> dracut:/# ls -la > >>>>>>> total 4 > >>>>>>> drwxr-xr-x 12 root 0 0 Sep 28 13:41 . > >>>>>>> drwxr-xr-x 12 root 0 0 Sep 28 13:41 .. > >>>>>>> -rw-r--r-- 1 root 0 0 Sep 28 13:41 .console_lock > >>>>>>> lrwxrwxrwx 1 root 0 7 Sep 20 16:37 bin -> usr/bin > >>>>>>> drwxr-xr-x 9 root 0 2340 Sep 28 13:38 dev > >>>>>>> drwxr-xr-x 8 root 0 0 Sep 28 13:41 etc > >>>>>>> lrwxrwxrwx 1 root 0 23 Sep 20 16:38 init -> > >>>>>>> usr/lib/systemd/systemd > >>>>>>> lrwxrwxrwx 1 root 0 7 Sep 20 16:37 lib -> usr/lib > >>>>>>> dr-xr-xr-x 50 root 0 0 Jan 1 1970 proc > >>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 root > >>>>>>> drwxr-xr-x 9 root 0 180 Sep 28 13:41 run > >>>>>>> lrwxrwxrwx 1 root 0 8 Sep 20 16:37 sbin -> usr/sbin > >>>>>>> -rwxr-xr-x 1 root 0 3041 Aug 10 01:11 shutdown > >>>>>>> dr-xr-xr-x 12 root 0 0 Sep 28 13:38 sys > >>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 sysroot > >>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 tmp > >>>>>>> drwxr-xr-x 6 root 0 0 Sep 20 16:37 usr > >>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 var > >>>>>>> dracut:/# > >>>>>>> dracut:/# ls -la dev/ | grep sd > >>>>>>> dracut:/# > >>>>>>> dracut:/# > >>>>>>> dracut:/# ls -la dev/ > >>>>>>> total 0 > >>>>>>> drwxr-xr-x 9 root 0 2340 Sep 28 13:38 . > >>>>>>> drwxr-xr-x 12 root 0 0 Sep 28 13:41 .. > >>>>>>> crw------- 1 root 0 10, 235 Sep 28 13:38 autofs > >>>>>>> drwxr-xr-x 2 root 0 200 Sep 28 13:38 block > >>>>>>> crw------- 1 root 0 10, 234 Sep 28 13:38 btrfs-control > >>>>>>> drwxr-xr-x 2 root 0 1940 Sep 28 13:38 char > >>>>>>> crw------- 1 root 0 5, 1 Sep 28 13:44 console > >>>>>>> crw------- 1 root 0 10, 62 Sep 28 13:38 cpu_dma_latency > >>>>>>> lrwxrwxrwx 1 root 0 13 Sep 28 13:38 fd -> /proc/self/fd > >>>>>>> crw-rw-rw- 1 root 0 1, 7 Sep 28 13:38 full > >>>>>>> crw-rw-rw- 1 root 0 10, 229 Sep 28 13:38 fuse > >>>>>>> drwxr-xr-x 2 root 0 60 Jan 1 1970 input > >>>>>>> crw-r--r-- 1 root 0 1, 11 Sep 28 13:38 kmsg > >>>>>>> srw-rw-rw- 1 root 0 0 Sep 28 13:38 log > >>>>>>> crw------- 1 root 0 10, 237 Sep 28 13:38 loop-control > >>>>>>> brw-rw---- 1 root disk 7, 0 Sep 28 13:38 loop0 > >>>>>>> brw-rw---- 1 root disk 7, 1 Sep 28 13:38 loop1 > >>>>>>> brw-rw---- 1 root disk 7, 2 Sep 28 13:38 loop2 > >>>>>>> brw-rw---- 1 root disk 7, 3 Sep 28 13:38 loop3 > >>>>>>> brw-rw---- 1 root disk 7, 4 Sep 28 13:38 loop4 > >>>>>>> brw-rw---- 1 root disk 7, 5 Sep 28 13:38 loop5 > >>>>>>> brw-rw---- 1 root disk 7, 6 Sep 28 13:38 loop6 > >>>>>>> brw-rw---- 1 root disk 7, 7 Sep 28 13:38 loop7 > >>>>>>> drwxr-xr-x 2 root 0 60 Jan 1 1970 mapper > >>>>>>> crw-r----- 1 root kmem 1, 1 Sep 28 13:38 mem > >>>>>>> crw------- 1 root 0 10, 61 Sep 28 13:38 network_latency > >>>>>>> crw------- 1 root 0 10, 60 Sep 28 13:38 network_throughput > >>>>>>> crw-rw-rw- 1 root 0 1, 3 Sep 28 13:38 null > >>>>>>> crw-r----- 1 root kmem 1, 4 Sep 28 13:38 port > >>>>>>> crw-rw-rw- 1 root tty 5, 2 Sep 28 13:38 ptmx > >>>>>>> drwxr-xr-x 2 root 0 0 Jan 1 1970 pts > >>>>>>> crw-rw-rw- 1 root 0 1, 8 Sep 28 13:38 random > >>>>>>> drwxr-xr-x 2 root 0 60 Jan 1 1970 raw > >>>>>>> crw-rw-r-- 1 root 0 10, 59 Sep 28 13:38 rfkill > >>>>>>> lrwxrwxrwx 1 root 0 4 Sep 28 13:38 rtc -> rtc0 > >>>>>>> crw------- 1 root 0 254, 0 Sep 28 13:38 rtc0 > >>>>>>> drwxrwxrwt 2 root 0 40 Sep 28 13:38 shm > >>>>>>> lrwxrwxrwx 1 root 0 15 Sep 28 13:38 stderr -> /proc/self/fd/2 > >>>>>>> lrwxrwxrwx 1 root 0 15 Sep 28 13:38 stdin -> /proc/self/fd/0 > >>>>>>> lrwxrwxrwx 1 root 0 15 Sep 28 13:38 stdout -> /proc/self/fd/1 > >>>>>>> crw-rw-rw- 1 root tty 5, 0 Sep 28 13:38 tty > >>>>>>> crw--w---- 1 root tty 4, 0 Sep 28 13:38 tty0 > >>>>>>> crw--w---- 1 root tty 4, 1 Sep 28 13:38 tty1 > >>>>>>> crw--w---- 1 root tty 4, 10 Sep 28 13:38 tty10 > >>>>>>> crw--w---- 1 root tty 4, 11 Sep 28 13:38 tty11 > >>>>>>> crw--w---- 1 root tty 4, 12 Sep 28 13:38 tty12 > >>>>>>> crw--w---- 1 root tty 4, 13 Sep 28 13:38 tty13 > >>>>>>> crw--w---- 1 root tty 4, 14 Sep 28 13:38 tty14 > >>>>>>> crw--w---- 1 root tty 4, 15 Sep 28 13:38 tty15 > >>>>>>> crw--w---- 1 root tty 4, 16 Sep 28 13:38 tty16 > >>>>>>> crw--w---- 1 root tty 4, 17 Sep 28 13:38 tty17 > >>>>>>> crw--w---- 1 root tty 4, 18 Sep 28 13:38 tty18 > >>>>>>> crw--w---- 1 root tty 4, 19 Sep 28 13:38 tty19 > >>>>>>> crw--w---- 1 root tty 4, 2 Sep 28 13:38 tty2 > >>>>>>> crw--w---- 1 root tty 4, 20 Sep 28 13:38 tty20 > >>>>>>> crw--w---- 1 root tty 4, 21 Sep 28 13:38 tty21 > >>>>>>> crw--w---- 1 root tty 4, 22 Sep 28 13:38 tty22 > >>>>>>> crw--w---- 1 root tty 4, 23 Sep 28 13:38 tty23 > >>>>>>> crw--w---- 1 root tty 4, 24 Sep 28 13:38 tty24 > >>>>>>> crw--w---- 1 root tty 4, 25 Sep 28 13:38 tty25 > >>>>>>> crw--w---- 1 root tty 4, 26 Sep 28 13:38 tty26 > >>>>>>> crw--w---- 1 root tty 4, 27 Sep 28 13:38 tty27 > >>>>>>> crw--w---- 1 root tty 4, 28 Sep 28 13:38 tty28 > >>>>>>> crw--w---- 1 root tty 4, 29 Sep 28 13:38 tty29 > >>>>>>> crw--w---- 1 root tty 4, 3 Sep 28 13:38 tty3 > >>>>>>> crw--w---- 1 root tty 4, 30 Sep 28 13:38 tty30 > >>>>>>> crw--w---- 1 root tty 4, 31 Sep 28 13:38 tty31 > >>>>>>> crw--w---- 1 root tty 4, 32 Sep 28 13:38 tty32 > >>>>>>> crw--w---- 1 root tty 4, 33 Sep 28 13:38 tty33 > >>>>>>> crw--w---- 1 root tty 4, 34 Sep 28 13:38 tty34 > >>>>>>> crw--w---- 1 root tty 4, 35 Sep 28 13:38 tty35 > >>>>>>> crw--w---- 1 root tty 4, 36 Sep 28 13:38 tty36 > >>>>>>> crw--w---- 1 root tty 4, 37 Sep 28 13:38 tty37 > >>>>>>> crw--w---- 1 root tty 4, 38 Sep 28 13:38 tty38 > >>>>>>> crw--w---- 1 root tty 4, 39 Sep 28 13:38 tty39 > >>>>>>> crw--w---- 1 root tty 4, 4 Sep 28 13:38 tty4 > >>>>>>> crw--w---- 1 root tty 4, 40 Sep 28 13:38 tty40 > >>>>>>> crw--w---- 1 root tty 4, 41 Sep 28 13:38 tty41 > >>>>>>> crw--w---- 1 root tty 4, 42 Sep 28 13:38 tty42 > >>>>>>> crw--w---- 1 root tty 4, 43 Sep 28 13:38 tty43 > >>>>>>> crw--w---- 1 root tty 4, 44 Sep 28 13:38 tty44 > >>>>>>> crw--w---- 1 root tty 4, 45 Sep 28 13:38 tty45 > >>>>>>> crw--w---- 1 root tty 4, 46 Sep 28 13:38 tty46 > >>>>>>> crw--w---- 1 root tty 4, 47 Sep 28 13:38 tty47 > >>>>>>> crw--w---- 1 root tty 4, 48 Sep 28 13:38 tty48 > >>>>>>> crw--w---- 1 root tty 4, 49 Sep 28 13:38 tty49 > >>>>>>> crw--w---- 1 root tty 4, 5 Sep 28 13:38 tty5 > >>>>>>> crw--w---- 1 root tty 4, 50 Sep 28 13:38 tty50 > >>>>>>> crw--w---- 1 root tty 4, 51 Sep 28 13:38 tty51 > >>>>>>> crw--w---- 1 root tty 4, 52 Sep 28 13:38 tty52 > >>>>>>> crw--w---- 1 root tty 4, 53 Sep 28 13:38 tty53 > >>>>>>> crw--w---- 1 root tty 4, 54 Sep 28 13:38 tty54 > >>>>>>> crw--w---- 1 root tty 4, 55 Sep 28 13:38 tty55 > >>>>>>> crw--w---- 1 root tty 4, 56 Sep 28 13:38 tty56 > >>>>>>> crw--w---- 1 root tty 4, 57 Sep 28 13:38 tty57 > >>>>>>> crw--w---- 1 root tty 4, 58 Sep 28 13:38 tty58 > >>>>>>> crw--w---- 1 root tty 4, 59 Sep 28 13:38 tty59 > >>>>>>> crw--w---- 1 root tty 4, 6 Sep 28 13:38 tty6 > >>>>>>> crw--w---- 1 root tty 4, 60 Sep 28 13:38 tty60 > >>>>>>> crw--w---- 1 root tty 4, 61 Sep 28 13:38 tty61 > >>>>>>> crw--w---- 1 root tty 4, 62 Sep 28 13:38 tty62 > >>>>>>> crw--w---- 1 root tty 4, 63 Sep 28 13:38 tty63 > >>>>>>> crw--w---- 1 root tty 4, 7 Sep 28 13:38 tty7 > >>>>>>> crw--w---- 1 root tty 4, 8 Sep 28 13:38 tty8 > >>>>>>> crw--w---- 1 root tty 4, 9 Sep 28 13:38 tty9 > >>>>>>> crw-rw---- 1 root dialout 4, 64 Sep 28 13:41 ttyS0 > >>>>>>> crw-rw---- 1 root dialout 4, 65 Sep 28 13:38 ttyS1 > >>>>>>> crw-rw---- 1 root dialout 4, 66 Sep 28 13:38 ttyS2 > >>>>>>> crw-rw---- 1 root dialout 4, 67 Sep 28 13:38 ttyS3 > >>>>>>> crw-rw-rw- 1 root 0 1, 9 Sep 28 13:38 urandom > >>>>>>> crw------- 1 root 0 251, 0 Sep 28 13:38 usbmon0 > >>>>>>> crw-rw---- 1 root tty 7, 0 Sep 28 13:38 vcs > >>>>>>> crw-rw---- 1 root tty 7, 1 Sep 28 13:38 vcs1 > >>>>>>> crw-rw---- 1 root tty 7, 128 Sep 28 13:38 vcsa > >>>>>>> crw-rw---- 1 root tty 7, 129 Sep 28 13:38 vcsa1 > >>>>>>> crw------- 1 root 0 10, 63 Sep 28 13:38 vga_arbiter > >>>>>>> crw-rw-rw- 1 root 0 1, 5 Sep 28 13:38 zero > >>>>>>> dracut:/# > >>>>>>> -----Original Message----- > >>>>>>> FROM: Gordan Bobic <[email protected]> > >>>>>>> Reply-to: [email protected] > >>>>>>> TO: [email protected] > >>>>>>> SUBJECT: Re: [RedSleeve-Users] Redsleeve 7.1 - loose ends > >>>>>>> DATE: Mon, 28 Sep 2015 14:15:17 +0100 > >>>>>>> What does: > >>>>>>> ls -la /dev/sd* > >>>>>>> show from the dracut prompt? > >>>>>>>> On 2015-09-28 13:28, ioan stan wrote: > >>>>>>>> I tried the setting below (and also with sda2), the booting > >>>>>>>> stops at > >>>>>>>> the same step. > >>>>>>>> bootargs=console=ttyS0,115200 root=/dev/sda1 rootwait > >>>>>>>> -----Original Message----- > >>>>>>>> FROM: Gordan Bobic <[email protected]> > >>>>>>>> Reply-to: [email protected] > >>>>>>>> TO: [email protected] > >>>>>>>> SUBJECT: Re: [RedSleeve-Users] Redsleeve 7.1 - loose ends > >>>>>>>> DATE: Mon, 28 Sep 2015 12:49:21 +0100 > >>>>>>>> The problem isn't in the uboot settings, it is in the file > >>>>>>>> system > >>>>>>> you > >>>>>>>> are > >>>>>>>> booting off. You are telling the kernel the rootfs is labeled > >>>>>>>> "rootfs". > >>>>>>>> Therefore you need to e2label the rootfs file system "rootfs" or > >>>>>>>> it > >>>>>>>> won't find it. > >>>>>>>> Alternatively change : > >>>>>>>>> bootargs=console=ttyS0,115200 root=LABEL=rootfs rootwait > >>>>>>>> to > >>>>>>>>> bootargs=console=ttyS0,115200 root=/dev/sda1 rootwait > >>>>>>>> assuming your rootfs is on sda1. > >>>>>>>> Gordan > >>>>>>>>> On 2015-09-28 12:43, Ioan Stan wrote: > >>>>>>>>> I'm not very proficient with u-boot, but the settings below > >>>>>>>>> work > >>>>>>>> when > >>>>>>>>> booting F18. > >>>>>>>>> Marvell>> printenv > >>>>>>>>> baudrate=115200 > >>>>>>>>> bootargs=console=ttyS0,115200 root=LABEL=rootfs rootwait > >>>>>>>>> bootargs_console=console=ttyS0,115200 selinux=0 > >>>>>>>>> elevator=deadline > >>>>>>>>> bootargs_root=rw root=/dev/nfs > >>>>>>>>> nfsroot=10.1.1.200:/nfsroot/guru,proto=tcp ip=dhcp > >>>>>>>>> bootcmd=usb start; ${loadImage}; ${loadInitrd} ; bootm > >>>>>>>>> 0x6400000 > >>>>>>>>> 0x7400000 > >>>>>>>>> bootcmd_tftp=dhcp; set serverip 10.1.1.200; tftpboot 0x6400000 > >>>>>>>>> sheeva-2.6.39.4-uImage > >>>>>>>>> bootdelay=3 > >>>>>>>>> eth1addr=delete > >>>>>>>>> ethact=egiga0 > >>>>>>>>> ethaddr=02:50:43:52:a6:2d > >>>>>>>>> ipaddr=10.1.1.221 > >>>>>>>>> loadImage=ext2load usb 0:1 0x6400000 uImage > >>>>>>>>> loadInitrd=ext2load usb 0:1 0x7400000 uInitrd > >>>>>>>>> serverip=10.1.1.200 > >>>>>>>>> stderr=serial > >>>>>>>>> stdin=serial > >>>>>>>>> stdout=serial > >>>>>>>>> x_bootargs=console=ttyS0,115200 > >>>>>>>>> x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs > >>>>>>>>> x_bootcmd_ethernet=ping 192.168.2.1 > >>>>>>>>> x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000 > >>>>>>>>> x_bootcmd_usb=usb start > >>>>>>>>> Environment size: 873/131068 bytes > >>>>>>>>> Marvell>> > >>>>>>>>>> On Sep 28, 2015, at 8:39 PM, Gordan Bobic > >>>>>>>>>> <[email protected]> > >>>>>>>>>> wrote: > >>>>>>>>>> Forgive the obviousness of the question, but did you e2label > >>>>>>>>>> the rootfs file system? > >>>>>>>>>> Gordan > >>>>>>>>>>> On 2015-09-28 12:28, Ioan Stan wrote: > >>>>>>>>>>> Sorry for my late reply. I get dracut error when trying to > >>>>>>>>>>> boot > >>>>>>>> from > >>>>>>>>>>> RSEL 7. Please let me know if you need other info. > >>>>>>>>>>> U-Boot 2011.12 (Mar 11 2012 - 18:53:15) > >>>>>>>>>>> Marvell-GuruPlug > >>>>>>>>>>> SoC: Kirkwood 88F6281_A1 > >>>>>>>>>>> DRAM: 512 MiB > >>>>>>>>>>> WARNING: Caches not enabled > >>>>>>>>>>> NAND: 512 MiB > >>>>>>>>>>> In: serial > >>>>>>>>>>> Out: serial > >>>>>>>>>>> Err: serial > >>>>>>>>>>> Net: egiga0, egiga1 > >>>>>>>>>>> 88E1121 Initialized on egiga0 > >>>>>>>>>>> PHY reset timed out > >>>>>>>>>>> 88E1121 Initialized on egiga1 > >>>>>>>>>>> Hit any key to stop autoboot: 0 > >>>>>>>>>>> (Re)start USB... > >>>>>>>>>>> USB: Register 10011 NbrPorts 1 > >>>>>>>>>>> USB EHCI 1.00 > >>>>>>>>>>> scanning bus for devices... 3 USB Device(s) found > >>>>>>>>>>> scanning bus for storage devices... 1 Storage Device(s) found > >>>>>>>>>>> Loading file "uImage" from usb device 0:1 (usbda1) > >>>>>>>>>>> 3665856 bytes read > >>>>>>>>>>> Loading file "uInitrd" from usb device 0:1 (usbda1) > >>>>>>>>>>> 17811253 bytes read > >>>>>>>>>>> ## Booting kernel from Legacy Image at 06400000 ... > >>>>>>>>>>> Image Name: 3.10.14-100.fc18.armv5tel.kirkwo > >>>>>>>>>>> Image Type: ARM Linux Kernel Image (uncompressed) > >>>>>>>>>>> Data Size: 3665792 Bytes = 3.5 MiB > >>>>>>>>>>> Load Address: 00008000 > >>>>>>>>>>> Entry Point: 00008000 > >>>>>>>>>>> Verifying Checksum ... OK > >>>>>>>>>>> ## Loading init Ramdisk from Legacy Image at 07400000 ... > >>>>>>>>>>> Image Name: initramfs > >>>>>>>>>>> Image Type: ARM Linux RAMDisk Image (uncompressed) > >>>>>>>>>>> Data Size: 17811189 Bytes = 17 MiB > >>>>>>>>>>> Load Address: 00000000 > >>>>>>>>>>> Entry Point: 00000000 > >>>>>>>>>>> Verifying Checksum ... OK > >>>>>>>>>>> Loading Kernel Image ... OK > >>>>>>>>>>> OK > >>>>>>>>>>> Starting kernel ... > >>>>>>>>>>> Uncompressing Linux... done, booting the kernel. > >>>>>>>>>>> [ 0.000000] Booting Linux on physical CPU 0x0 > >>>>>>>>>>> [ 0.000000] Initializing cgroup subsys cpuset > >>>>>>>>>>> [ 0.000000] Initializing cgroup subsys cpu > >>>>>>>>>>> [ 0.000000] Initializing cgroup subsys cpuacct > >>>>>>>>>>> [ 0.000000] Linux version 3.10.14-100.fc18.armv5tel.kirkwood > >>>>>>>>>>> ([email protected]) (gcc 3 > >>>>>>>>>>> [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1 > >>>>>>> (ARMv5TE), > >>>>>>>>>>> cr=00053977 > >>>>>>>>>>> [ 0.000000] CPU: VIVT data cache, VIVT instruction cache > >>>>>>>>>>> [ 0.000000] Machine: Marvell GuruPlug Reference Board > >>>>>>>>>>> [ 0.000000] Memory policy: ECC disabled, Data cache writeback > >>>>>>>>>>> [ 0.000000] Built 1 zonelists in Zone order, mobility > >>>>>>>>>>> grouping > >>>>>>> on. > >>>>>>>>>>> Total pages: 130048 > >>>>>>>>>>> [ 0.000000] Kernel command line: console=ttyS0,115200 > >>>>>>>>>>> root=LABEL=rootfs rootwait > >>>>>>>>>>> [ 0.000000] PID hash table entries: 2048 (order: 1, 8192 > >>>>>>>>>>> bytes) > >>>>>>>>>>> [ 0.000000] Dentry cache hash table entries: 65536 (order: 6, > >>>>>>>>>>> 262144 bytes) > >>>>>>>>>>> [ 0.000000] Inode-cache hash table entries: 32768 (order: 5, > >>>>>>>>>>> 131072 bytes) > >>>>>>>>>>> [ 0.000000] allocated 1048576 bytes of page_cgroup > >>>>>>>>>>> [ 0.000000] please try 'cgroup_disable=memory' option if you > >>>>>>> don't > >>>>>>>>>>> want memory cgroups > >>>>>>>>>>> [ 0.000000] Memory: 512MB = 512MB total > >>>>>>>>>>> [ 0.000000] Memory: 493024k/493024k available, 31264k > >>>>>>>>>>> reserved, > >>>>>>> 0K > >>>>>>>>>>> highmem > >>>>>>>>>>> [ 0.000000] Virtual kernel memory layout: > >>>>>>>>>>> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB) > >>>>>>>>>>> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) > >>>>>>>>>>> [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB) > >>>>>>>>>>> [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB) > >>>>>>>>>>> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) > >>>>>>>>>>> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB) > >>>>>>>>>>> [ 0.000000] .text : 0xc0008000 - 0xc0678cbc (6596 kB) > >>>>>>>>>>> [ 0.000000] .init : 0xc0679000 - 0xc06d112c ( 353 kB) > >>>>>>>>>>> [ 0.000000] .data : 0xc06d2000 - 0xc073ffb0 ( 440 kB) > >>>>>>>>>>> [ 0.000000] .bss : 0xc073ffb0 - 0xc081ac30 ( 876 kB) > >>>>>>>>>>> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0, > >>>>>>>>>>> CPUs=1, > >>>>>>>>>>> Nodes=1 > >>>>>>>>>>> [ 0.000000] NR_IRQS:114 > >>>>>>>>>>> [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns, > >>>>>>>>>>> wraps > >>>>>>>>>>> every 21474ms > >>>>>>>>>>> [ 0.000000] Console: colour dummy device 80x30 > >>>>>>>>>>> [ 2.767292] Calibrating delay loop... 1191.11 BogoMIPS > >>>>>>>>>>> (lpj=5955584) > >>>>>>>>>>> [ 2.857166] pid_max: default: 32768 minimum: 301 > >>>>>>>>>>> [ 2.857335] Security Framework initialized > >>>>>>>>>>> [ 2.857379] SELinux: Initializing. > >>>>>>>>>>> [ 2.857686] Mount-cache hash table entries: 512 > >>>>>>>>>>> [ 2.858360] Initializing cgroup subsys memory > >>>>>>>>>>> [ 2.858411] Initializing cgroup subsys devices > >>>>>>>>>>> [ 2.858425] Initializing cgroup subsys freezer > >>>>>>>>>>> [ 2.858435] Initializing cgroup subsys net_cls > >>>>>>>>>>> [ 2.858444] Initializing cgroup subsys blkio > >>>>>>>>>>> [ 2.858453] Initializing cgroup subsys perf_event > >>>>>>>>>>> [ 2.858597] CPU: Testing write buffer coherency: ok > >>>>>>>>>>> [ 2.858700] ftrace: allocating 19764 entries in 39 pages > >>>>>>>>>>> [ 2.888683] Setting up static identity map for 0xc048aed8 - > >>>>>>>>>>> 0xc048af14 > >>>>>>>>>>> [ 2.900719] devtmpfs: initialized > >>>>>>>>>>> [ 2.909222] atomic64 test passed > >>>>>>>>>>> [ 2.909237] pinctrl core: initialized pinctrl subsystem > >>>>>>>>>>> [ 2.909686] regulator-dummy: no parameters > >>>>>>>>>>> [ 2.910062] NET: Registered protocol family 16 > >>>>>>>>>>> [ 2.910494] DMA: preallocated 256 KiB pool for atomic > >>>>>>>>>>> coherent > >>>>>>>>>>> allocations > >>>>>>>>>>> [ 2.911276] Kirkwood: MV88F6281-A1, TCLK=200000000. > >>>>>>>>>>> [ 2.911304] Feroceon L2: Enabling L2 > >>>>>>>>>>> [ 2.911341] Feroceon L2: Cache support initialised, in WT > >>>>>>> override > >>>>>>>>>>> mode. > >>>>>>>>>>> [ 2.917315] bio: create slab <bio-0> at 0 > >>>>>>>>>>> [ 2.917938] vgaarb: loaded > >>>>>>>>>>> [ 2.918313] SCSI subsystem initialized > >>>>>>>>>>> [ 2.918706] usbcore: registered new interface driver usbfs > >>>>>>>>>>> [ 2.918759] usbcore: registered new interface driver hub > >>>>>>>>>>> [ 2.918865] usbcore: registered new device driver usb > >>>>>>>>>>> [ 2.919575] NetLabel: Initializing > >>>>>>>>>>> [ 2.919585] NetLabel: domain hash size = 128 > >>>>>>>>>>> [ 2.919590] NetLabel: protocols = UNLABELED CIPSOv4 > >>>>>>>>>>> [ 2.919646] NetLabel: unlabeled traffic allowed by default > >>>>>>>>>>> [ 2.919739] Switching to clocksource orion_clocksource > >>>>>>>>>>> [ 2.964353] NET: Registered protocol family 2 > >>>>>>>>>>> [ 2.965044] TCP established hash table entries: 4096 (order: > >>>>>>>>>>> 3, > >>>>>>>>>>> 32768 bytes) > >>>>>>>>>>> [ 2.965144] TCP bind hash table entries: 4096 (order: 2, > >>>>>>>>>>> 16384 > >>>>>>>>>>> bytes) > >>>>>>>>>>> [ 2.965195] TCP: Hash tables configured (established 4096 > >>>>>>>>>>> bind > >>>>>>>>>>> 4096) > >>>>>>>>>>> [ 2.965252] TCP: reno registered > >>>>>>>>>>> [ 2.965265] UDP hash table entries: 256 (order: 0, 4096 > >>>>>>>>>>> bytes) > >>>>>>>>>>> [ 2.965287] UDP-Lite hash table entries: 256 (order: 0, 4096 > >>>>>>>>>>> bytes) > >>>>>>>>>>> [ 2.965536] NET: Registered protocol family 1 > >>>>>>>>>>> [ 2.965770] Unpacking initramfs... > >>>>>>>>>>> [ 4.505970] Freeing initrd memory: 17388K (c7401000 - > >>>>>>>>>>> c84fc000) > >>>>>>>>>>> [ 4.506712] audit: initializing netlink socket (disabled) > >>>>>>>>>>> [ 4.506755] type=2000 audit(1.730:1): initialized > >>>>>>>>>>> [ 4.649878] VFS: Disk quotas dquot_6.5.2 > >>>>>>>>>>> [ 4.650069] Dquot-cache hash table entries: 1024 (order 0, > >>>>>>>>>>> 4096 > >>>>>>>>>>> bytes) > >>>>>>>>>>> [ 4.651722] msgmni has been set to 996 > >>>>>>>>>>> [ 4.653977] alg: No test for stdrng (krng) > >>>>>>>>>>> [ 4.654001] NET: Registered protocol family 38 > >>>>>>>>>>> [ 4.654094] Block layer SCSI generic (bsg) driver version 0.4 > >>>>>>>>>>> loaded (major 252) > >>>>>>>>>>> [ 4.654239] io scheduler noop registered > >>>>>>>>>>> [ 4.654248] io scheduler deadline registered > >>>>>>>>>>> [ 4.654438] io scheduler cfq registered (default) > >>>>>>>>>>> [ 4.654937] mv_xor mv_xor.0: Marvell shared XOR driver > >>>>>>>>>>> [ 4.689874] mv_xor mv_xor.0: Marvell XOR: ( xor cpy ) > >>>>>>>>>>> [ 4.729871] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy ) > >>>>>>>>>>> [ 4.730009] mv_xor mv_xor.1: Marvell shared XOR driver > >>>>>>>>>>> [ 4.769872] mv_xor mv_xor.1: Marvell XOR: ( xor cpy ) > >>>>>>>>>>> [ 4.809871] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy ) > >>>>>>>>>>> [ 4.810253] Serial: 8250/16550 driver, 4 ports, IRQ sharing > >>>>>>>>>>> enabled > >>>>>>>>>>> [ 4.831325] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33) > >>>>>>>>>>> is > >>>>>>> a > >>>>>>>>>>> 16550A > >>>>>>>>>>> [ 5.341356] console [ttyS0] enabled > >>>>>>>>>>> [ 5.349314] loop: module loaded > >>>>>>>>>>> [ 5.353009] libphy: Fixed MDIO Bus: probed > >>>>>>>>>>> [ 5.357333] ehci_hcd: USB 2.0 'Enhanced' Host Controller > >>>>>>>>>>> (EHCI) > >>>>>>>>>>> Driver > >>>>>>>>>>> [ 5.363908] ehci-pci: EHCI PCI platform driver > >>>>>>>>>>> [ 5.368426] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) > >>>>>>> Driver > >>>>>>>>>>> [ 5.374686] uhci_hcd: USB Universal Host Controller Interface > >>>>>>>>>>> driver > >>>>>>>>>>> [ 5.381335] usbcore: registered new interface driver > >>>>>>>>>>> usbserial > >>>>>>>>>>> [ 5.387229] usbcore: registered new interface driver > >>>>>>>>>>> usbserial_generic > >>>>>>>>>>> [ 5.393856] usbserial: USB Serial support registered for > >>>>>>>>>>> generic > >>>>>>>>>>> [ 5.400134] mousedev: PS/2 mouse device common for all mice > >>>>>>>>>>> [ 5.406313] rtc-mv rtc-mv: rtc core: registered rtc-mv as > >>>>>>>>>>> rtc0 > >>>>>>>>>>> [ 5.412714] device-mapper: uevent: version 1.0.3 > >>>>>>>>>>> [ 5.417700] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15) > >>>>>>>>>>> initialised: [email protected] > >>>>>>>>>>> [ 5.426260] cpuidle: using governor ladder > >>>>>>>>>>> [ 5.430392] cpuidle: using governor menu > >>>>>>>>>>> [ 5.434550] hidraw: raw HID events driver (C) Jiri Kosina > >>>>>>>>>>> [ 5.440614] usbcore: registered new interface driver usbhid > >>>>>>>>>>> [ 5.446210] usbhid: USB HID core driver > >>>>>>>>>>> [ 5.450164] drop_monitor: Initializing network drop monitor > >>>>>>>>>>> service > >>>>>>>>>>> [ 5.456781] ip_tables: (C) 2000-2006 Netfilter Core Team > >>>>>>>>>>> [ 5.462192] TCP: cubic registered > >>>>>>>>>>> [ 5.465519] Initializing XFRM netlink socket > >>>>>>>>>>> [ 5.470658] NET: Registered protocol family 10 > >>>>>>>>>>> [ 5.475820] mip6: Mobile IPv6 > >>>>>>>>>>> [ 5.478801] NET: Registered protocol family 17 > >>>>>>>>>>> [ 5.483885] registered taskstats version 1 > >>>>>>>>>>> [ 5.488343] rtc-mv rtc-mv: setting system clock to 2015-09-27 > >>>>>>>>>>> 19:57:03 UTC (1443383823) > >>>>>>>>>>> [ 5.497876] Freeing unused kernel memory: 352K (c0679000 - > >>>>>>>>>>> c06d1000) > >>>>>>>>>>> [ 5.528598] systemd[1]: systemd 208 running in system mode. > >>>>>>>>>>> (+PAM > >>>>>>>>>>> +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTS) > >>>>>>>>>>> [ 5.541643] systemd[1]: Running in initial RAM disk. > >>>>>>>>>>> Welcome to RedSleeve Linux 7 (Core) dracut-033-241.el7.5 > >>>>>>>> (Initramfs)! > >>>>>>>>>>> [ 5.570158] systemd[1]: No hostname configured. > >>>>>>>>>>> [ 5.574732] systemd[1]: Set hostname to <localhost>. > >>>>>>>>>>> [ 5.580294] systemd[1]: Initializing machine ID from random > >>>>>>>>>>> generator. > >>>>>>>>>>> [ 5.820021] systemd[1]: Expecting device > >>>>>>>>>>> dev-disk-by\x2dlabel-rootfs.device... > >>>>>>>>>>> Expecting device dev-disk-by\x2dlabel-rootfs.device... > >>>>>>>>>>> [ 5.849927] systemd[1]: Starting -.slice. > >>>>>>>>>>> [ OK ] Created slice -.slice. > >>>>>>>>>>> [ 5.869906] systemd[1]: Created slice -.slice. > >>>>>>>>>>> [ 5.874729] systemd[1]: Starting System Slice. > >>>>>>>>>>> [ OK ] Created slice System Slice. > >>>>>>>>>>> [ 5.899902] systemd[1]: Created slice System Slice. > >>>>>>>>>>> [ 5.905124] systemd[1]: Starting Slices. > >>>>>>>>>>> [ OK ] Reached target Slices. > >>>>>>>>>>> [ 5.929891] systemd[1]: Reached target Slices. > >>>>>>>>>>> [ 5.934655] systemd[1]: Starting Timers. > >>>>>>>>>>> [ OK ] Reached target Timers. > >>>>>>>>>>> [ 5.959887] systemd[1]: Reached target Timers. > >>>>>>>>>>> [ 5.964652] systemd[1]: Starting Journal Socket. > >>>>>>>>>>> [ OK ] Listening on Journal Socket. > >>>>>>>>>>> [ 5.989898] systemd[1]: Listening on Journal Socket. > >>>>>>>>>>> [ 5.995537] systemd[1]: Started dracut ask for additional > >>>>>>>>>>> cmdline > >>>>>>>>>>> parameters. > >>>>>>>>>>> [ 6.003884] systemd[1]: Started dracut cmdline hook. > >>>>>>>>>>> [ 6.010230] systemd[1]: Started dracut pre-udev hook. > >>>>>>>>>>> [ 6.015601] systemd[1]: Starting Apply Kernel Variables... > >>>>>>>>>>> Starting Apply Kernel Variables... > >>>>>>>>>>> [ 6.043113] systemd[1]: Started Load Kernel Modules. > >>>>>>>>>>> [ 6.048554] systemd[1]: Starting Create list of required > >>>>>>>>>>> static > >>>>>>>>>>> device nodes for the current kernel... > >>>>>>>>>>> Starting Create list of required static device nodes...rrent > >>>>>>>>>>> kernel... > >>>>>>>>>>> [ 6.092081] systemd[1]: Starting Setup Virtual Console... > >>>>>>>>>>> Starting Setup Virtual Console... > >>>>>>>>>>> [ 6.109634] systemd[1]: Starting Journal Service... > >>>>>>>>>>> Starting Journal Service... > >>>>>>>>>>> [ OK ] Started Journal Service. > >>>>>>>>>>> [ 6.150073] systemd[1]: Started Journal Service. > >>>>>>>>>>> [ OK ] Listening on udev Kernel Socket. > >>>>>>>>>>> [ OK ] Listening on udev Control Socket. > >>>>>>>>>>> [ OK ] Reached target Sockets. > >>>>>>>>>>> [ OK ] Reached target Swap. > >>>>>>>>>>> [ OK ] Reached target Local File Systems. > >>>>>>>>>>> [ OK ] Started Apply Kernel Variables. > >>>>>>>>>>> [ OK ] Started Setup Virtual Console. > >>>>>>>>>>> [ OK ] Started Create list of required static device nodes > >>>>>>>>>>> ...current kernel. > >>>>>>>>>>> Starting Create static device nodes in /dev... > >>>>>>>>>>> [ OK ] Started Create static device nodes in /dev. > >>>>>>>>>>> Starting udev Kernel Device Manager... > >>>>>>>>>>> [ OK [ 6.444780] systemd-udevd[70]: starting version 208 > >>>>>>>>>>> ] Started udev Kernel Device Manager. > >>>>>>>>>>> Starting udev Coldplug all Devices... > >>>>>>>>>>> [ OK ] Started udev Coldplug all Devices. > >>>>>>>>>>> Starting dracut initqueue hook... > >>>>>>>>>>> [ OK ] Reached target System Initialization. > >>>>>>>>>>> Starting Show Plymouth Boot Screen... > >>>>>>>>>>> Mounting Configuration File System... > >>>>>>>>>>> [ OK ] Mounted Configuration File System. > >>>>>>>>>>> [ OK ] Started Show Plymouth Boot Screen. > >>>>>>>>>>> [ OK ] Reached target Paths. > >>>>>>>>>>> [ OK ] Reached target Basic System. > >>>>>>>>>>> [ 6.974377] sata_mv sata_mv.0: cannot get optional clkdev > >>>>>>>>>>> [ 7.041830] sata_mv sata_mv.0: slots 32 ports 1 > >>>>>>>>>>> [ 7.132086] scsi0 : sata_mv > >>>>>>>>>>> [ 7.135215] ata1: SATA max UDMA/133 irq 21 > >>>>>>>>>>> G[ 7.158580] mvsdio mvsdio: no pins associated > >>>>>>>>>>> [ 7.199841] mvsdio mvsdio: lacking card detect (fall back to > >>>>>>>>>>> polling) > >>>>>>>>>>> [ 7.239248] mmc0: new high speed SDIO card at address 0001 > >>>>>>>>>>> [ 7.335884] cfg80211: Calling CRDA to update world regulatory > >>>>>>>>>>> domain > >>>>>>>>>>> [ 7.349952] libertas_sdio: Libertas SDIO driver > >>>>>>>>>>> [ 7.354506] libertas_sdio: Copyright Pierre Ossman > >>>>>>>>>>> [ 7.361833] libertas_sdio: failed to find firmware (-2) > >>>>>>>>>>> [ 7.479794] ata1: SATA link down (SStatus 0 SControl F300) > >>>>>>>>>>> dracut-initqueue[85]: Warning: Could not boot. > >>>>>>>>>>> [ OK ] Mounted Configuration File System. > >>>>>>>>>>> [ OK ] Started Show Plymouth Boot Screen. > >>>>>>>>>>> [ OK ] Reached target Paths. > >>>>>>>>>>> [ OK ] Reached target Basic System. > >>>>>>>>>>> Gdracut-initqueue[85]: Warning: Could not boot. > >>>>>>>>>>> dracut-initqueue[85]: Warning: /dev/disk/by-label/rootfs does > >>>>>>>>>>> not > >>>>>>>>>>> exist > >>>>>>>>>>> Starting Dracut Emergency Shell... > >>>>>>>>>>> Warning: /dev/disk/by-label/rootfs does not exist > >>>>>>>>>>> Generating "/run/initramfs/rdsosreport.txt" > >>>>>>>>>>> Entering emergency mode. Exit the shell to continue. > >>>>>>>>>>> Type "journalctl" to view system logs. > >>>>>>>>>>> You might want to save "/run/initramfs/rdsosreport.txt" to a > >>>>>>>>>>> USB > >>>>>>>>>>> stick or /boot > >>>>>>>>>>> after mounting them and attach it to a bug report. > >>>>>>>>>>> dracut:/# > >>>>>>>>>>>> On Sep 21, 2015, at 2:34 AM, Jacco Ligthart > >>>>>>> <[email protected]> > >>>>>>>>>>>> wrote: > >>>>>>>>>>>>> On 09/20/15 19:18, Ioan Stan wrote: > >>>>>>>>>>>>> Hi Jacco, > >>>>>>>>>>>>> Really appreciated. Before proceeding, I'd like to confirm > >>>>>>>>>>>>> the > >>>>>>>>>>>>> steps (assuming similar procedure as for F18 in the link > >>>>>>>>>>>>> below) > >>>>>>>>>>>>> 1. xzcat dream* /dev/sdb (if the SD card is sdb; or use dd) > >>>>>>>>>>>>> 2. Configure u-boot (one that supports ext2) > >>>>>>>>>>>>> printenv > >>>>>>>>>>>>> set bootargs 'console=ttyS0,115200 root=LABEL=rootfs > >>>>>>>>>>>>> rootwait' > >>>>>>>>>>>>> set loadInitrd 'ext2load usb 1:1 0x7400000 uInitrd' > >>>>>>>>>>>>> set loadImage 'ext2load usb 1:1 0x6400000 uImage' > >>>>>>>>>>>>> set bootcmd 'usb start; ${loadImage}; ${loadInitrd} ; bootm > >>>>>>>>>>>>> 0x6400000 0x7400000' > >>>>>>>>>>>>> saveenv > >>>>>>>>>>>>> boot > >>>>>>>>>>>> yes, that's also how I think it should work. The first > >>>>>>>>>>>> partition > >>>>>>>> in > >>>>>>>>>>>> the image is an ext2 partition with indeed the files uInitrd > >>>>>>>>>>>> and > >>>>>>>>>>>> uImage. These files come from a kernel-kirkwood of F18. I'm > >>>>>>>>>>>> not > >>>>>>>> sure > >>>>>>>>>>>> if the uboot things should reference usb if we really boot > >>>>>>>>>>>> from > >>>>>>>> SD, > >>>>>>>>>>>> but if this works for you right now for F18, it should be > >>>>>>> similar > >>>>>>>>>>>> for RSEL7. > >>>>>>>>>>>> Jacco > >>>>>> _______________________________________________ > >>>>>> users mailing list > >>>>>> [email protected] > >>>>>> http://lists.redsleeve.org/mailman/listinfo/users > >>>>> _______________________________________________ > >>>>> users mailing list > >>>>> [email protected] > >>>>> http://lists.redsleeve.org/mailman/listinfo/users > >>>> _______________________________________________ > >>>> users mailing list > >>>> [email protected] > >>>> http://lists.redsleeve.org/mailman/listinfo/users > >> > >> _______________________________________________ > >> users mailing list > >> [email protected] > >> http://lists.redsleeve.org/mailman/listinfo/users > > _______________________________________________ > > users mailing list > > [email protected] > > http://lists.redsleeve.org/mailman/listinfo/users > > _______________________________________________ > users mailing list > [email protected] > http://lists.redsleeve.org/mailman/listinfo/users _______________________________________________ users mailing list [email protected] http://lists.redsleeve.org/mailman/listinfo/users
