It's not a kernel bug, it's a dracut bug that I was talking about.
The problem is that dracut wasn't including ehci-orion USB driver
in the initramfs. Once you figure out what the root cause of the
problem is, it is trivially fixable with the configuration option
I listed below.
From here I should be able to follow the standard RSEL recipe:
1) Grab a working kernel uImage, /lib/firmware, and
/lib/modules/$kernel/
2) Drop them into the RSEL image
3) Make the configuration changes mentioned below (also remember to
blacklist the orion_nand driver due to the GuruPlug/DreamPlug machid
confusion issue, as loading the orion_nand driver on DreamPlug will
hang)
4) Rebuild initramfs using dracut, and uboot it using mkimage
And that should just work.
For completeness and neatness, I will put together a kernel package
that can be installed using rpm and facilitate seamless kernel
upgrades.
Another package that may require revisiting in RSEL to facilitate
seamless kernel upgrades is grubby, as this handles re-packing
vmlinux and initramfs into uImage/uInitrd.
Gordan
On 2015-10-21 03:09, Ioan Stan wrote:
> I would just mention that Debian Jessie runs fine on dreamplug. I can
> check the exact kernel when I get back home later today.
>
> Sent from my iPhone
>
>> On 2015/10/21, at 10:20, Gordan Bobic <[email protected]> wrote:
>>
>> Figured it out in the end.
>>
>> The problem is that ehci-orion driver went from being built into
>> the kernel in the 3.6.x kernel on F18, to it being built as a
>> module. But - dracut didn't figure out that the ehci-orion
>> driver is vital for the usb-storage driver to find anything.
>>
>> Solution is to:
>>
>> 1) add
>> add_drivers+="ehci-orion"
>> to /etc/dracut.conf
>>
>> 2) Rebuild the initramfs:
>> dracut -f -v /boot/initramfs-3.10.90-kirkwood.img 3.10.90-kirkwood
>> (adjust for your kernel name and version)
>>
>> 3) Make uInitrd from the initramfs:
>> mkimage -A arm -O linux -T ramdisk -C none -a 0 -e 0 -n initramfs -d
>> /boot/initramfs-3.10.90-kirkwood.img /boot/uInitrd
>> (make sure your uImage matches the kernel you are building the uInitrd
>> for)
>>
>> Then it all boots fine.
>>
>> So, now that the part of working around bugs in Fedora is done,
>> I might actually be able to get somewhere with getting RedSleeve
>> to work on this thing...
>>
>> Best of all, the mainline 3.10.90 kernel seems to just work and
>> support all the hardware. And firmware auto-loading works, too.
>>
>> The question now is - do we try to stick with 3.10.x LT kernel
>> for as much hardware as possible, since that is sort of almost
>> similar to what EL7 ships (don't get me started on the upstream
>> kernel patches)? Or do we perhaps skip to the the currently
>> latest LT kernel series (3.18.x)? In theory, later kernels might
>> allow supporting more devices with a single kernel code base
>> (only different configs), rather than having 3.10 kernels for
>> some well supported SoCs like the Kirkwood, and having to
>> use later LT kernels for other things anyway.
>>
>> I can see the pros and cons either way, but I am leaning toward
>> jumping up to 3.18.x mainline LT kernels. Any opinions on this
>> from anyone here?
>>
>> Gordan
>>
>>
>>
>>> On 2015-10-20 10:37, Gordan Bobic wrote:
>>> I left the latest vanilla 3.10.90 kernel building this morning. I'm
>>> hoping to try it tonight. Fingers crossed that will just work. If the
>>> firmware loading is still broken (it is also broken on F18 with their
>>> 3.6.10 kernel) the only workaround I am aware of is to build the
>>> firmware blobs into the kernel binary. I had to do this with the
>>> 3.4 kernel for the Samsung Exynos Chromebook.
>>> Gordan
>>>> On 2015-10-19 22:59, ioan stan wrote:
>>>> Thank you, Gordon.
>>>>> On Oct 20, 2015, at 05:02, Gordan Bobic <[email protected]>
>>>>> wrote:
>>>>> I'm now looking into getting DreamPlugs running, and I've
>>>>> hit the same problem. The problem seems to be particularly
>>>>> related to the 3.10.14 kernel shipping with Fedora, in that
>>>>> it's usb-storage driver is broken on the DreamPlug - it never
>>>>> detects any USB storage devices.
>>>>> The 3.6.10 kernel from the original F18 ARM release works
>>>>> fine, however.
>>>>> Additionally, I updated the u-boot on my DP to
>>>>> 2014.10+dfsg1-5, and that version requires machid to be
>>>>> set to the GuruPlug's ID (annoyingly):
>>>>> machid=0xa63
>>>>> Presumably the old 2011 firmware had this ID in bdinfo, and
>>>>> the 3.6 and 3.10 kernels aren't new enough to recognise the
>>>>> proper DP machid.
>>>>> Of course, all sorts of other things are broken in the F18
>>>>> standard image as well (firmware loading fails for the WiFi
>>>>> module, courtesy of systemd removing support for udev firmware
>>>>> loader helpers, and the kernel's module loader being broken
>>>>> until more recent kernels).
>>>>> Gordan
>>>>>> On 2015-09-28 15:01, Gordan Bobic wrote:
>>>>>> It looks like your initramfs doesn't include the USB disk driver.
>>>>>> The device nodes aren't there.
>>>>>> Gordan
>>>>>>> On 2015-09-28 14:46, ioan stan wrote:
>>>>>>> Please see below.
>>>>>>> dracut:/# ls -la
>>>>>>> total 4
>>>>>>> drwxr-xr-x 12 root 0 0 Sep 28 13:41 .
>>>>>>> drwxr-xr-x 12 root 0 0 Sep 28 13:41 ..
>>>>>>> -rw-r--r-- 1 root 0 0 Sep 28 13:41 .console_lock
>>>>>>> lrwxrwxrwx 1 root 0 7 Sep 20 16:37 bin -> usr/bin
>>>>>>> drwxr-xr-x 9 root 0 2340 Sep 28 13:38 dev
>>>>>>> drwxr-xr-x 8 root 0 0 Sep 28 13:41 etc
>>>>>>> lrwxrwxrwx 1 root 0 23 Sep 20 16:38 init ->
>>>>>>> usr/lib/systemd/systemd
>>>>>>> lrwxrwxrwx 1 root 0 7 Sep 20 16:37 lib -> usr/lib
>>>>>>> dr-xr-xr-x 50 root 0 0 Jan 1 1970 proc
>>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 root
>>>>>>> drwxr-xr-x 9 root 0 180 Sep 28 13:41 run
>>>>>>> lrwxrwxrwx 1 root 0 8 Sep 20 16:37 sbin -> usr/sbin
>>>>>>> -rwxr-xr-x 1 root 0 3041 Aug 10 01:11 shutdown
>>>>>>> dr-xr-xr-x 12 root 0 0 Sep 28 13:38 sys
>>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 sysroot
>>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 tmp
>>>>>>> drwxr-xr-x 6 root 0 0 Sep 20 16:37 usr
>>>>>>> drwxr-xr-x 2 root 0 0 Sep 20 16:37 var
>>>>>>> dracut:/#
>>>>>>> dracut:/# ls -la dev/ | grep sd
>>>>>>> dracut:/#
>>>>>>> dracut:/#
>>>>>>> dracut:/# ls -la dev/
>>>>>>> total 0
>>>>>>> drwxr-xr-x 9 root 0 2340 Sep 28 13:38 .
>>>>>>> drwxr-xr-x 12 root 0 0 Sep 28 13:41 ..
>>>>>>> crw------- 1 root 0 10, 235 Sep 28 13:38 autofs
>>>>>>> drwxr-xr-x 2 root 0 200 Sep 28 13:38 block
>>>>>>> crw------- 1 root 0 10, 234 Sep 28 13:38 btrfs-control
>>>>>>> drwxr-xr-x 2 root 0 1940 Sep 28 13:38 char
>>>>>>> crw------- 1 root 0 5, 1 Sep 28 13:44 console
>>>>>>> crw------- 1 root 0 10, 62 Sep 28 13:38 cpu_dma_latency
>>>>>>> lrwxrwxrwx 1 root 0 13 Sep 28 13:38 fd -> /proc/self/fd
>>>>>>> crw-rw-rw- 1 root 0 1, 7 Sep 28 13:38 full
>>>>>>> crw-rw-rw- 1 root 0 10, 229 Sep 28 13:38 fuse
>>>>>>> drwxr-xr-x 2 root 0 60 Jan 1 1970 input
>>>>>>> crw-r--r-- 1 root 0 1, 11 Sep 28 13:38 kmsg
>>>>>>> srw-rw-rw- 1 root 0 0 Sep 28 13:38 log
>>>>>>> crw------- 1 root 0 10, 237 Sep 28 13:38 loop-control
>>>>>>> brw-rw---- 1 root disk 7, 0 Sep 28 13:38 loop0
>>>>>>> brw-rw---- 1 root disk 7, 1 Sep 28 13:38 loop1
>>>>>>> brw-rw---- 1 root disk 7, 2 Sep 28 13:38 loop2
>>>>>>> brw-rw---- 1 root disk 7, 3 Sep 28 13:38 loop3
>>>>>>> brw-rw---- 1 root disk 7, 4 Sep 28 13:38 loop4
>>>>>>> brw-rw---- 1 root disk 7, 5 Sep 28 13:38 loop5
>>>>>>> brw-rw---- 1 root disk 7, 6 Sep 28 13:38 loop6
>>>>>>> brw-rw---- 1 root disk 7, 7 Sep 28 13:38 loop7
>>>>>>> drwxr-xr-x 2 root 0 60 Jan 1 1970 mapper
>>>>>>> crw-r----- 1 root kmem 1, 1 Sep 28 13:38 mem
>>>>>>> crw------- 1 root 0 10, 61 Sep 28 13:38 network_latency
>>>>>>> crw------- 1 root 0 10, 60 Sep 28 13:38 network_throughput
>>>>>>> crw-rw-rw- 1 root 0 1, 3 Sep 28 13:38 null
>>>>>>> crw-r----- 1 root kmem 1, 4 Sep 28 13:38 port
>>>>>>> crw-rw-rw- 1 root tty 5, 2 Sep 28 13:38 ptmx
>>>>>>> drwxr-xr-x 2 root 0 0 Jan 1 1970 pts
>>>>>>> crw-rw-rw- 1 root 0 1, 8 Sep 28 13:38 random
>>>>>>> drwxr-xr-x 2 root 0 60 Jan 1 1970 raw
>>>>>>> crw-rw-r-- 1 root 0 10, 59 Sep 28 13:38 rfkill
>>>>>>> lrwxrwxrwx 1 root 0 4 Sep 28 13:38 rtc -> rtc0
>>>>>>> crw------- 1 root 0 254, 0 Sep 28 13:38 rtc0
>>>>>>> drwxrwxrwt 2 root 0 40 Sep 28 13:38 shm
>>>>>>> lrwxrwxrwx 1 root 0 15 Sep 28 13:38 stderr -> /proc/self/fd/2
>>>>>>> lrwxrwxrwx 1 root 0 15 Sep 28 13:38 stdin -> /proc/self/fd/0
>>>>>>> lrwxrwxrwx 1 root 0 15 Sep 28 13:38 stdout -> /proc/self/fd/1
>>>>>>> crw-rw-rw- 1 root tty 5, 0 Sep 28 13:38 tty
>>>>>>> crw--w---- 1 root tty 4, 0 Sep 28 13:38 tty0
>>>>>>> crw--w---- 1 root tty 4, 1 Sep 28 13:38 tty1
>>>>>>> crw--w---- 1 root tty 4, 10 Sep 28 13:38 tty10
>>>>>>> crw--w---- 1 root tty 4, 11 Sep 28 13:38 tty11
>>>>>>> crw--w---- 1 root tty 4, 12 Sep 28 13:38 tty12
>>>>>>> crw--w---- 1 root tty 4, 13 Sep 28 13:38 tty13
>>>>>>> crw--w---- 1 root tty 4, 14 Sep 28 13:38 tty14
>>>>>>> crw--w---- 1 root tty 4, 15 Sep 28 13:38 tty15
>>>>>>> crw--w---- 1 root tty 4, 16 Sep 28 13:38 tty16
>>>>>>> crw--w---- 1 root tty 4, 17 Sep 28 13:38 tty17
>>>>>>> crw--w---- 1 root tty 4, 18 Sep 28 13:38 tty18
>>>>>>> crw--w---- 1 root tty 4, 19 Sep 28 13:38 tty19
>>>>>>> crw--w---- 1 root tty 4, 2 Sep 28 13:38 tty2
>>>>>>> crw--w---- 1 root tty 4, 20 Sep 28 13:38 tty20
>>>>>>> crw--w---- 1 root tty 4, 21 Sep 28 13:38 tty21
>>>>>>> crw--w---- 1 root tty 4, 22 Sep 28 13:38 tty22
>>>>>>> crw--w---- 1 root tty 4, 23 Sep 28 13:38 tty23
>>>>>>> crw--w---- 1 root tty 4, 24 Sep 28 13:38 tty24
>>>>>>> crw--w---- 1 root tty 4, 25 Sep 28 13:38 tty25
>>>>>>> crw--w---- 1 root tty 4, 26 Sep 28 13:38 tty26
>>>>>>> crw--w---- 1 root tty 4, 27 Sep 28 13:38 tty27
>>>>>>> crw--w---- 1 root tty 4, 28 Sep 28 13:38 tty28
>>>>>>> crw--w---- 1 root tty 4, 29 Sep 28 13:38 tty29
>>>>>>> crw--w---- 1 root tty 4, 3 Sep 28 13:38 tty3
>>>>>>> crw--w---- 1 root tty 4, 30 Sep 28 13:38 tty30
>>>>>>> crw--w---- 1 root tty 4, 31 Sep 28 13:38 tty31
>>>>>>> crw--w---- 1 root tty 4, 32 Sep 28 13:38 tty32
>>>>>>> crw--w---- 1 root tty 4, 33 Sep 28 13:38 tty33
>>>>>>> crw--w---- 1 root tty 4, 34 Sep 28 13:38 tty34
>>>>>>> crw--w---- 1 root tty 4, 35 Sep 28 13:38 tty35
>>>>>>> crw--w---- 1 root tty 4, 36 Sep 28 13:38 tty36
>>>>>>> crw--w---- 1 root tty 4, 37 Sep 28 13:38 tty37
>>>>>>> crw--w---- 1 root tty 4, 38 Sep 28 13:38 tty38
>>>>>>> crw--w---- 1 root tty 4, 39 Sep 28 13:38 tty39
>>>>>>> crw--w---- 1 root tty 4, 4 Sep 28 13:38 tty4
>>>>>>> crw--w---- 1 root tty 4, 40 Sep 28 13:38 tty40
>>>>>>> crw--w---- 1 root tty 4, 41 Sep 28 13:38 tty41
>>>>>>> crw--w---- 1 root tty 4, 42 Sep 28 13:38 tty42
>>>>>>> crw--w---- 1 root tty 4, 43 Sep 28 13:38 tty43
>>>>>>> crw--w---- 1 root tty 4, 44 Sep 28 13:38 tty44
>>>>>>> crw--w---- 1 root tty 4, 45 Sep 28 13:38 tty45
>>>>>>> crw--w---- 1 root tty 4, 46 Sep 28 13:38 tty46
>>>>>>> crw--w---- 1 root tty 4, 47 Sep 28 13:38 tty47
>>>>>>> crw--w---- 1 root tty 4, 48 Sep 28 13:38 tty48
>>>>>>> crw--w---- 1 root tty 4, 49 Sep 28 13:38 tty49
>>>>>>> crw--w---- 1 root tty 4, 5 Sep 28 13:38 tty5
>>>>>>> crw--w---- 1 root tty 4, 50 Sep 28 13:38 tty50
>>>>>>> crw--w---- 1 root tty 4, 51 Sep 28 13:38 tty51
>>>>>>> crw--w---- 1 root tty 4, 52 Sep 28 13:38 tty52
>>>>>>> crw--w---- 1 root tty 4, 53 Sep 28 13:38 tty53
>>>>>>> crw--w---- 1 root tty 4, 54 Sep 28 13:38 tty54
>>>>>>> crw--w---- 1 root tty 4, 55 Sep 28 13:38 tty55
>>>>>>> crw--w---- 1 root tty 4, 56 Sep 28 13:38 tty56
>>>>>>> crw--w---- 1 root tty 4, 57 Sep 28 13:38 tty57
>>>>>>> crw--w---- 1 root tty 4, 58 Sep 28 13:38 tty58
>>>>>>> crw--w---- 1 root tty 4, 59 Sep 28 13:38 tty59
>>>>>>> crw--w---- 1 root tty 4, 6 Sep 28 13:38 tty6
>>>>>>> crw--w---- 1 root tty 4, 60 Sep 28 13:38 tty60
>>>>>>> crw--w---- 1 root tty 4, 61 Sep 28 13:38 tty61
>>>>>>> crw--w---- 1 root tty 4, 62 Sep 28 13:38 tty62
>>>>>>> crw--w---- 1 root tty 4, 63 Sep 28 13:38 tty63
>>>>>>> crw--w---- 1 root tty 4, 7 Sep 28 13:38 tty7
>>>>>>> crw--w---- 1 root tty 4, 8 Sep 28 13:38 tty8
>>>>>>> crw--w---- 1 root tty 4, 9 Sep 28 13:38 tty9
>>>>>>> crw-rw---- 1 root dialout 4, 64 Sep 28 13:41 ttyS0
>>>>>>> crw-rw---- 1 root dialout 4, 65 Sep 28 13:38 ttyS1
>>>>>>> crw-rw---- 1 root dialout 4, 66 Sep 28 13:38 ttyS2
>>>>>>> crw-rw---- 1 root dialout 4, 67 Sep 28 13:38 ttyS3
>>>>>>> crw-rw-rw- 1 root 0 1, 9 Sep 28 13:38 urandom
>>>>>>> crw------- 1 root 0 251, 0 Sep 28 13:38 usbmon0
>>>>>>> crw-rw---- 1 root tty 7, 0 Sep 28 13:38 vcs
>>>>>>> crw-rw---- 1 root tty 7, 1 Sep 28 13:38 vcs1
>>>>>>> crw-rw---- 1 root tty 7, 128 Sep 28 13:38 vcsa
>>>>>>> crw-rw---- 1 root tty 7, 129 Sep 28 13:38 vcsa1
>>>>>>> crw------- 1 root 0 10, 63 Sep 28 13:38 vga_arbiter
>>>>>>> crw-rw-rw- 1 root 0 1, 5 Sep 28 13:38 zero
>>>>>>> dracut:/#
>>>>>>> -----Original Message-----
>>>>>>> FROM: Gordan Bobic <[email protected]>
>>>>>>> Reply-to: [email protected]
>>>>>>> TO: [email protected]
>>>>>>> SUBJECT: Re: [RedSleeve-Users] Redsleeve 7.1 - loose ends
>>>>>>> DATE: Mon, 28 Sep 2015 14:15:17 +0100
>>>>>>> What does:
>>>>>>> ls -la /dev/sd*
>>>>>>> show from the dracut prompt?
>>>>>>>> On 2015-09-28 13:28, ioan stan wrote:
>>>>>>>> I tried the setting below (and also with sda2), the booting
>>>>>>>> stops at
>>>>>>>> the same step.
>>>>>>>> bootargs=console=ttyS0,115200 root=/dev/sda1 rootwait
>>>>>>>> -----Original Message-----
>>>>>>>> FROM: Gordan Bobic <[email protected]>
>>>>>>>> Reply-to: [email protected]
>>>>>>>> TO: [email protected]
>>>>>>>> SUBJECT: Re: [RedSleeve-Users] Redsleeve 7.1 - loose ends
>>>>>>>> DATE: Mon, 28 Sep 2015 12:49:21 +0100
>>>>>>>> The problem isn't in the uboot settings, it is in the file
>>>>>>>> system
>>>>>>> you
>>>>>>>> are
>>>>>>>> booting off. You are telling the kernel the rootfs is labeled
>>>>>>>> "rootfs".
>>>>>>>> Therefore you need to e2label the rootfs file system "rootfs" or
>>>>>>>> it
>>>>>>>> won't find it.
>>>>>>>> Alternatively change :
>>>>>>>>> bootargs=console=ttyS0,115200 root=LABEL=rootfs rootwait
>>>>>>>> to
>>>>>>>>> bootargs=console=ttyS0,115200 root=/dev/sda1 rootwait
>>>>>>>> assuming your rootfs is on sda1.
>>>>>>>> Gordan
>>>>>>>>> On 2015-09-28 12:43, Ioan Stan wrote:
>>>>>>>>> I'm not very proficient with u-boot, but the settings below
>>>>>>>>> work
>>>>>>>> when
>>>>>>>>> booting F18.
>>>>>>>>> Marvell>> printenv
>>>>>>>>> baudrate=115200
>>>>>>>>> bootargs=console=ttyS0,115200 root=LABEL=rootfs rootwait
>>>>>>>>> bootargs_console=console=ttyS0,115200 selinux=0
>>>>>>>>> elevator=deadline
>>>>>>>>> bootargs_root=rw root=/dev/nfs
>>>>>>>>> nfsroot=10.1.1.200:/nfsroot/guru,proto=tcp ip=dhcp
>>>>>>>>> bootcmd=usb start; ${loadImage}; ${loadInitrd} ; bootm
>>>>>>>>> 0x6400000
>>>>>>>>> 0x7400000
>>>>>>>>> bootcmd_tftp=dhcp; set serverip 10.1.1.200; tftpboot 0x6400000
>>>>>>>>> sheeva-2.6.39.4-uImage
>>>>>>>>> bootdelay=3
>>>>>>>>> eth1addr=delete
>>>>>>>>> ethact=egiga0
>>>>>>>>> ethaddr=02:50:43:52:a6:2d
>>>>>>>>> ipaddr=10.1.1.221
>>>>>>>>> loadImage=ext2load usb 0:1 0x6400000 uImage
>>>>>>>>> loadInitrd=ext2load usb 0:1 0x7400000 uInitrd
>>>>>>>>> serverip=10.1.1.200
>>>>>>>>> stderr=serial
>>>>>>>>> stdin=serial
>>>>>>>>> stdout=serial
>>>>>>>>> x_bootargs=console=ttyS0,115200
>>>>>>>>> x_bootargs_root=ubi.mtd=2 root=ubi0:rootfs rootfstype=ubifs
>>>>>>>>> x_bootcmd_ethernet=ping 192.168.2.1
>>>>>>>>> x_bootcmd_kernel=nand read.e 0x6400000 0x100000 0x400000
>>>>>>>>> x_bootcmd_usb=usb start
>>>>>>>>> Environment size: 873/131068 bytes
>>>>>>>>> Marvell>>
>>>>>>>>>> On Sep 28, 2015, at 8:39 PM, Gordan Bobic
>>>>>>>>>> <[email protected]>
>>>>>>>>>> wrote:
>>>>>>>>>> Forgive the obviousness of the question, but did you e2label
>>>>>>>>>> the rootfs file system?
>>>>>>>>>> Gordan
>>>>>>>>>>> On 2015-09-28 12:28, Ioan Stan wrote:
>>>>>>>>>>> Sorry for my late reply. I get dracut error when trying to
>>>>>>>>>>> boot
>>>>>>>> from
>>>>>>>>>>> RSEL 7. Please let me know if you need other info.
>>>>>>>>>>> U-Boot 2011.12 (Mar 11 2012 - 18:53:15)
>>>>>>>>>>> Marvell-GuruPlug
>>>>>>>>>>> SoC: Kirkwood 88F6281_A1
>>>>>>>>>>> DRAM: 512 MiB
>>>>>>>>>>> WARNING: Caches not enabled
>>>>>>>>>>> NAND: 512 MiB
>>>>>>>>>>> In: serial
>>>>>>>>>>> Out: serial
>>>>>>>>>>> Err: serial
>>>>>>>>>>> Net: egiga0, egiga1
>>>>>>>>>>> 88E1121 Initialized on egiga0
>>>>>>>>>>> PHY reset timed out
>>>>>>>>>>> 88E1121 Initialized on egiga1
>>>>>>>>>>> Hit any key to stop autoboot: 0
>>>>>>>>>>> (Re)start USB...
>>>>>>>>>>> USB: Register 10011 NbrPorts 1
>>>>>>>>>>> USB EHCI 1.00
>>>>>>>>>>> scanning bus for devices... 3 USB Device(s) found
>>>>>>>>>>> scanning bus for storage devices... 1 Storage Device(s) found
>>>>>>>>>>> Loading file "uImage" from usb device 0:1 (usbda1)
>>>>>>>>>>> 3665856 bytes read
>>>>>>>>>>> Loading file "uInitrd" from usb device 0:1 (usbda1)
>>>>>>>>>>> 17811253 bytes read
>>>>>>>>>>> ## Booting kernel from Legacy Image at 06400000 ...
>>>>>>>>>>> Image Name: 3.10.14-100.fc18.armv5tel.kirkwo
>>>>>>>>>>> Image Type: ARM Linux Kernel Image (uncompressed)
>>>>>>>>>>> Data Size: 3665792 Bytes = 3.5 MiB
>>>>>>>>>>> Load Address: 00008000
>>>>>>>>>>> Entry Point: 00008000
>>>>>>>>>>> Verifying Checksum ... OK
>>>>>>>>>>> ## Loading init Ramdisk from Legacy Image at 07400000 ...
>>>>>>>>>>> Image Name: initramfs
>>>>>>>>>>> Image Type: ARM Linux RAMDisk Image (uncompressed)
>>>>>>>>>>> Data Size: 17811189 Bytes = 17 MiB
>>>>>>>>>>> Load Address: 00000000
>>>>>>>>>>> Entry Point: 00000000
>>>>>>>>>>> Verifying Checksum ... OK
>>>>>>>>>>> Loading Kernel Image ... OK
>>>>>>>>>>> OK
>>>>>>>>>>> Starting kernel ...
>>>>>>>>>>> Uncompressing Linux... done, booting the kernel.
>>>>>>>>>>> [ 0.000000] Booting Linux on physical CPU 0x0
>>>>>>>>>>> [ 0.000000] Initializing cgroup subsys cpuset
>>>>>>>>>>> [ 0.000000] Initializing cgroup subsys cpu
>>>>>>>>>>> [ 0.000000] Initializing cgroup subsys cpuacct
>>>>>>>>>>> [ 0.000000] Linux version 3.10.14-100.fc18.armv5tel.kirkwood
>>>>>>>>>>> ([email protected]) (gcc 3
>>>>>>>>>>> [ 0.000000] CPU: Feroceon 88FR131 [56251311] revision 1
>>>>>>> (ARMv5TE),
>>>>>>>>>>> cr=00053977
>>>>>>>>>>> [ 0.000000] CPU: VIVT data cache, VIVT instruction cache
>>>>>>>>>>> [ 0.000000] Machine: Marvell GuruPlug Reference Board
>>>>>>>>>>> [ 0.000000] Memory policy: ECC disabled, Data cache writeback
>>>>>>>>>>> [ 0.000000] Built 1 zonelists in Zone order, mobility
>>>>>>>>>>> grouping
>>>>>>> on.
>>>>>>>>>>> Total pages: 130048
>>>>>>>>>>> [ 0.000000] Kernel command line: console=ttyS0,115200
>>>>>>>>>>> root=LABEL=rootfs rootwait
>>>>>>>>>>> [ 0.000000] PID hash table entries: 2048 (order: 1, 8192
>>>>>>>>>>> bytes)
>>>>>>>>>>> [ 0.000000] Dentry cache hash table entries: 65536 (order: 6,
>>>>>>>>>>> 262144 bytes)
>>>>>>>>>>> [ 0.000000] Inode-cache hash table entries: 32768 (order: 5,
>>>>>>>>>>> 131072 bytes)
>>>>>>>>>>> [ 0.000000] allocated 1048576 bytes of page_cgroup
>>>>>>>>>>> [ 0.000000] please try 'cgroup_disable=memory' option if you
>>>>>>> don't
>>>>>>>>>>> want memory cgroups
>>>>>>>>>>> [ 0.000000] Memory: 512MB = 512MB total
>>>>>>>>>>> [ 0.000000] Memory: 493024k/493024k available, 31264k
>>>>>>>>>>> reserved,
>>>>>>> 0K
>>>>>>>>>>> highmem
>>>>>>>>>>> [ 0.000000] Virtual kernel memory layout:
>>>>>>>>>>> [ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)
>>>>>>>>>>> [ 0.000000] fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB)
>>>>>>>>>>> [ 0.000000] vmalloc : 0xe0800000 - 0xff000000 ( 488 MB)
>>>>>>>>>>> [ 0.000000] lowmem : 0xc0000000 - 0xe0000000 ( 512 MB)
>>>>>>>>>>> [ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)
>>>>>>>>>>> [ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)
>>>>>>>>>>> [ 0.000000] .text : 0xc0008000 - 0xc0678cbc (6596 kB)
>>>>>>>>>>> [ 0.000000] .init : 0xc0679000 - 0xc06d112c ( 353 kB)
>>>>>>>>>>> [ 0.000000] .data : 0xc06d2000 - 0xc073ffb0 ( 440 kB)
>>>>>>>>>>> [ 0.000000] .bss : 0xc073ffb0 - 0xc081ac30 ( 876 kB)
>>>>>>>>>>> [ 0.000000] SLUB: HWalign=32, Order=0-3, MinObjects=0,
>>>>>>>>>>> CPUs=1,
>>>>>>>>>>> Nodes=1
>>>>>>>>>>> [ 0.000000] NR_IRQS:114
>>>>>>>>>>> [ 0.000000] sched_clock: 32 bits at 200MHz, resolution 5ns,
>>>>>>>>>>> wraps
>>>>>>>>>>> every 21474ms
>>>>>>>>>>> [ 0.000000] Console: colour dummy device 80x30
>>>>>>>>>>> [ 2.767292] Calibrating delay loop... 1191.11 BogoMIPS
>>>>>>>>>>> (lpj=5955584)
>>>>>>>>>>> [ 2.857166] pid_max: default: 32768 minimum: 301
>>>>>>>>>>> [ 2.857335] Security Framework initialized
>>>>>>>>>>> [ 2.857379] SELinux: Initializing.
>>>>>>>>>>> [ 2.857686] Mount-cache hash table entries: 512
>>>>>>>>>>> [ 2.858360] Initializing cgroup subsys memory
>>>>>>>>>>> [ 2.858411] Initializing cgroup subsys devices
>>>>>>>>>>> [ 2.858425] Initializing cgroup subsys freezer
>>>>>>>>>>> [ 2.858435] Initializing cgroup subsys net_cls
>>>>>>>>>>> [ 2.858444] Initializing cgroup subsys blkio
>>>>>>>>>>> [ 2.858453] Initializing cgroup subsys perf_event
>>>>>>>>>>> [ 2.858597] CPU: Testing write buffer coherency: ok
>>>>>>>>>>> [ 2.858700] ftrace: allocating 19764 entries in 39 pages
>>>>>>>>>>> [ 2.888683] Setting up static identity map for 0xc048aed8 -
>>>>>>>>>>> 0xc048af14
>>>>>>>>>>> [ 2.900719] devtmpfs: initialized
>>>>>>>>>>> [ 2.909222] atomic64 test passed
>>>>>>>>>>> [ 2.909237] pinctrl core: initialized pinctrl subsystem
>>>>>>>>>>> [ 2.909686] regulator-dummy: no parameters
>>>>>>>>>>> [ 2.910062] NET: Registered protocol family 16
>>>>>>>>>>> [ 2.910494] DMA: preallocated 256 KiB pool for atomic
>>>>>>>>>>> coherent
>>>>>>>>>>> allocations
>>>>>>>>>>> [ 2.911276] Kirkwood: MV88F6281-A1, TCLK=200000000.
>>>>>>>>>>> [ 2.911304] Feroceon L2: Enabling L2
>>>>>>>>>>> [ 2.911341] Feroceon L2: Cache support initialised, in WT
>>>>>>> override
>>>>>>>>>>> mode.
>>>>>>>>>>> [ 2.917315] bio: create slab <bio-0> at 0
>>>>>>>>>>> [ 2.917938] vgaarb: loaded
>>>>>>>>>>> [ 2.918313] SCSI subsystem initialized
>>>>>>>>>>> [ 2.918706] usbcore: registered new interface driver usbfs
>>>>>>>>>>> [ 2.918759] usbcore: registered new interface driver hub
>>>>>>>>>>> [ 2.918865] usbcore: registered new device driver usb
>>>>>>>>>>> [ 2.919575] NetLabel: Initializing
>>>>>>>>>>> [ 2.919585] NetLabel: domain hash size = 128
>>>>>>>>>>> [ 2.919590] NetLabel: protocols = UNLABELED CIPSOv4
>>>>>>>>>>> [ 2.919646] NetLabel: unlabeled traffic allowed by default
>>>>>>>>>>> [ 2.919739] Switching to clocksource orion_clocksource
>>>>>>>>>>> [ 2.964353] NET: Registered protocol family 2
>>>>>>>>>>> [ 2.965044] TCP established hash table entries: 4096 (order:
>>>>>>>>>>> 3,
>>>>>>>>>>> 32768 bytes)
>>>>>>>>>>> [ 2.965144] TCP bind hash table entries: 4096 (order: 2,
>>>>>>>>>>> 16384
>>>>>>>>>>> bytes)
>>>>>>>>>>> [ 2.965195] TCP: Hash tables configured (established 4096
>>>>>>>>>>> bind
>>>>>>>>>>> 4096)
>>>>>>>>>>> [ 2.965252] TCP: reno registered
>>>>>>>>>>> [ 2.965265] UDP hash table entries: 256 (order: 0, 4096
>>>>>>>>>>> bytes)
>>>>>>>>>>> [ 2.965287] UDP-Lite hash table entries: 256 (order: 0, 4096
>>>>>>>>>>> bytes)
>>>>>>>>>>> [ 2.965536] NET: Registered protocol family 1
>>>>>>>>>>> [ 2.965770] Unpacking initramfs...
>>>>>>>>>>> [ 4.505970] Freeing initrd memory: 17388K (c7401000 -
>>>>>>>>>>> c84fc000)
>>>>>>>>>>> [ 4.506712] audit: initializing netlink socket (disabled)
>>>>>>>>>>> [ 4.506755] type=2000 audit(1.730:1): initialized
>>>>>>>>>>> [ 4.649878] VFS: Disk quotas dquot_6.5.2
>>>>>>>>>>> [ 4.650069] Dquot-cache hash table entries: 1024 (order 0,
>>>>>>>>>>> 4096
>>>>>>>>>>> bytes)
>>>>>>>>>>> [ 4.651722] msgmni has been set to 996
>>>>>>>>>>> [ 4.653977] alg: No test for stdrng (krng)
>>>>>>>>>>> [ 4.654001] NET: Registered protocol family 38
>>>>>>>>>>> [ 4.654094] Block layer SCSI generic (bsg) driver version 0.4
>>>>>>>>>>> loaded (major 252)
>>>>>>>>>>> [ 4.654239] io scheduler noop registered
>>>>>>>>>>> [ 4.654248] io scheduler deadline registered
>>>>>>>>>>> [ 4.654438] io scheduler cfq registered (default)
>>>>>>>>>>> [ 4.654937] mv_xor mv_xor.0: Marvell shared XOR driver
>>>>>>>>>>> [ 4.689874] mv_xor mv_xor.0: Marvell XOR: ( xor cpy )
>>>>>>>>>>> [ 4.729871] mv_xor mv_xor.0: Marvell XOR: ( xor fill cpy )
>>>>>>>>>>> [ 4.730009] mv_xor mv_xor.1: Marvell shared XOR driver
>>>>>>>>>>> [ 4.769872] mv_xor mv_xor.1: Marvell XOR: ( xor cpy )
>>>>>>>>>>> [ 4.809871] mv_xor mv_xor.1: Marvell XOR: ( xor fill cpy )
>>>>>>>>>>> [ 4.810253] Serial: 8250/16550 driver, 4 ports, IRQ sharing
>>>>>>>>>>> enabled
>>>>>>>>>>> [ 4.831325] serial8250.0: ttyS0 at MMIO 0xf1012000 (irq = 33)
>>>>>>>>>>> is
>>>>>>> a
>>>>>>>>>>> 16550A
>>>>>>>>>>> [ 5.341356] console [ttyS0] enabled
>>>>>>>>>>> [ 5.349314] loop: module loaded
>>>>>>>>>>> [ 5.353009] libphy: Fixed MDIO Bus: probed
>>>>>>>>>>> [ 5.357333] ehci_hcd: USB 2.0 'Enhanced' Host Controller
>>>>>>>>>>> (EHCI)
>>>>>>>>>>> Driver
>>>>>>>>>>> [ 5.363908] ehci-pci: EHCI PCI platform driver
>>>>>>>>>>> [ 5.368426] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI)
>>>>>>> Driver
>>>>>>>>>>> [ 5.374686] uhci_hcd: USB Universal Host Controller Interface
>>>>>>>>>>> driver
>>>>>>>>>>> [ 5.381335] usbcore: registered new interface driver
>>>>>>>>>>> usbserial
>>>>>>>>>>> [ 5.387229] usbcore: registered new interface driver
>>>>>>>>>>> usbserial_generic
>>>>>>>>>>> [ 5.393856] usbserial: USB Serial support registered for
>>>>>>>>>>> generic
>>>>>>>>>>> [ 5.400134] mousedev: PS/2 mouse device common for all mice
>>>>>>>>>>> [ 5.406313] rtc-mv rtc-mv: rtc core: registered rtc-mv as
>>>>>>>>>>> rtc0
>>>>>>>>>>> [ 5.412714] device-mapper: uevent: version 1.0.3
>>>>>>>>>>> [ 5.417700] device-mapper: ioctl: 4.24.0-ioctl (2013-01-15)
>>>>>>>>>>> initialised: [email protected]
>>>>>>>>>>> [ 5.426260] cpuidle: using governor ladder
>>>>>>>>>>> [ 5.430392] cpuidle: using governor menu
>>>>>>>>>>> [ 5.434550] hidraw: raw HID events driver (C) Jiri Kosina
>>>>>>>>>>> [ 5.440614] usbcore: registered new interface driver usbhid
>>>>>>>>>>> [ 5.446210] usbhid: USB HID core driver
>>>>>>>>>>> [ 5.450164] drop_monitor: Initializing network drop monitor
>>>>>>>>>>> service
>>>>>>>>>>> [ 5.456781] ip_tables: (C) 2000-2006 Netfilter Core Team
>>>>>>>>>>> [ 5.462192] TCP: cubic registered
>>>>>>>>>>> [ 5.465519] Initializing XFRM netlink socket
>>>>>>>>>>> [ 5.470658] NET: Registered protocol family 10
>>>>>>>>>>> [ 5.475820] mip6: Mobile IPv6
>>>>>>>>>>> [ 5.478801] NET: Registered protocol family 17
>>>>>>>>>>> [ 5.483885] registered taskstats version 1
>>>>>>>>>>> [ 5.488343] rtc-mv rtc-mv: setting system clock to 2015-09-27
>>>>>>>>>>> 19:57:03 UTC (1443383823)
>>>>>>>>>>> [ 5.497876] Freeing unused kernel memory: 352K (c0679000 -
>>>>>>>>>>> c06d1000)
>>>>>>>>>>> [ 5.528598] systemd[1]: systemd 208 running in system mode.
>>>>>>>>>>> (+PAM
>>>>>>>>>>> +LIBWRAP +AUDIT +SELINUX +IMA +SYSVINIT +LIBCRYPTS)
>>>>>>>>>>> [ 5.541643] systemd[1]: Running in initial RAM disk.
>>>>>>>>>>> Welcome to RedSleeve Linux 7 (Core) dracut-033-241.el7.5
>>>>>>>> (Initramfs)!
>>>>>>>>>>> [ 5.570158] systemd[1]: No hostname configured.
>>>>>>>>>>> [ 5.574732] systemd[1]: Set hostname to <localhost>.
>>>>>>>>>>> [ 5.580294] systemd[1]: Initializing machine ID from random
>>>>>>>>>>> generator.
>>>>>>>>>>> [ 5.820021] systemd[1]: Expecting device
>>>>>>>>>>> dev-disk-by\x2dlabel-rootfs.device...
>>>>>>>>>>> Expecting device dev-disk-by\x2dlabel-rootfs.device...
>>>>>>>>>>> [ 5.849927] systemd[1]: Starting -.slice.
>>>>>>>>>>> [ OK ] Created slice -.slice.
>>>>>>>>>>> [ 5.869906] systemd[1]: Created slice -.slice.
>>>>>>>>>>> [ 5.874729] systemd[1]: Starting System Slice.
>>>>>>>>>>> [ OK ] Created slice System Slice.
>>>>>>>>>>> [ 5.899902] systemd[1]: Created slice System Slice.
>>>>>>>>>>> [ 5.905124] systemd[1]: Starting Slices.
>>>>>>>>>>> [ OK ] Reached target Slices.
>>>>>>>>>>> [ 5.929891] systemd[1]: Reached target Slices.
>>>>>>>>>>> [ 5.934655] systemd[1]: Starting Timers.
>>>>>>>>>>> [ OK ] Reached target Timers.
>>>>>>>>>>> [ 5.959887] systemd[1]: Reached target Timers.
>>>>>>>>>>> [ 5.964652] systemd[1]: Starting Journal Socket.
>>>>>>>>>>> [ OK ] Listening on Journal Socket.
>>>>>>>>>>> [ 5.989898] systemd[1]: Listening on Journal Socket.
>>>>>>>>>>> [ 5.995537] systemd[1]: Started dracut ask for additional
>>>>>>>>>>> cmdline
>>>>>>>>>>> parameters.
>>>>>>>>>>> [ 6.003884] systemd[1]: Started dracut cmdline hook.
>>>>>>>>>>> [ 6.010230] systemd[1]: Started dracut pre-udev hook.
>>>>>>>>>>> [ 6.015601] systemd[1]: Starting Apply Kernel Variables...
>>>>>>>>>>> Starting Apply Kernel Variables...
>>>>>>>>>>> [ 6.043113] systemd[1]: Started Load Kernel Modules.
>>>>>>>>>>> [ 6.048554] systemd[1]: Starting Create list of required
>>>>>>>>>>> static
>>>>>>>>>>> device nodes for the current kernel...
>>>>>>>>>>> Starting Create list of required static device nodes...rrent
>>>>>>>>>>> kernel...
>>>>>>>>>>> [ 6.092081] systemd[1]: Starting Setup Virtual Console...
>>>>>>>>>>> Starting Setup Virtual Console...
>>>>>>>>>>> [ 6.109634] systemd[1]: Starting Journal Service...
>>>>>>>>>>> Starting Journal Service...
>>>>>>>>>>> [ OK ] Started Journal Service.
>>>>>>>>>>> [ 6.150073] systemd[1]: Started Journal Service.
>>>>>>>>>>> [ OK ] Listening on udev Kernel Socket.
>>>>>>>>>>> [ OK ] Listening on udev Control Socket.
>>>>>>>>>>> [ OK ] Reached target Sockets.
>>>>>>>>>>> [ OK ] Reached target Swap.
>>>>>>>>>>> [ OK ] Reached target Local File Systems.
>>>>>>>>>>> [ OK ] Started Apply Kernel Variables.
>>>>>>>>>>> [ OK ] Started Setup Virtual Console.
>>>>>>>>>>> [ OK ] Started Create list of required static device nodes
>>>>>>>>>>> ...current kernel.
>>>>>>>>>>> Starting Create static device nodes in /dev...
>>>>>>>>>>> [ OK ] Started Create static device nodes in /dev.
>>>>>>>>>>> Starting udev Kernel Device Manager...
>>>>>>>>>>> [ OK [ 6.444780] systemd-udevd[70]: starting version 208
>>>>>>>>>>> ] Started udev Kernel Device Manager.
>>>>>>>>>>> Starting udev Coldplug all Devices...
>>>>>>>>>>> [ OK ] Started udev Coldplug all Devices.
>>>>>>>>>>> Starting dracut initqueue hook...
>>>>>>>>>>> [ OK ] Reached target System Initialization.
>>>>>>>>>>> Starting Show Plymouth Boot Screen...
>>>>>>>>>>> Mounting Configuration File System...
>>>>>>>>>>> [ OK ] Mounted Configuration File System.
>>>>>>>>>>> [ OK ] Started Show Plymouth Boot Screen.
>>>>>>>>>>> [ OK ] Reached target Paths.
>>>>>>>>>>> [ OK ] Reached target Basic System.
>>>>>>>>>>> [ 6.974377] sata_mv sata_mv.0: cannot get optional clkdev
>>>>>>>>>>> [ 7.041830] sata_mv sata_mv.0: slots 32 ports 1
>>>>>>>>>>> [ 7.132086] scsi0 : sata_mv
>>>>>>>>>>> [ 7.135215] ata1: SATA max UDMA/133 irq 21
>>>>>>>>>>> G[ 7.158580] mvsdio mvsdio: no pins associated
>>>>>>>>>>> [ 7.199841] mvsdio mvsdio: lacking card detect (fall back to
>>>>>>>>>>> polling)
>>>>>>>>>>> [ 7.239248] mmc0: new high speed SDIO card at address 0001
>>>>>>>>>>> [ 7.335884] cfg80211: Calling CRDA to update world regulatory
>>>>>>>>>>> domain
>>>>>>>>>>> [ 7.349952] libertas_sdio: Libertas SDIO driver
>>>>>>>>>>> [ 7.354506] libertas_sdio: Copyright Pierre Ossman
>>>>>>>>>>> [ 7.361833] libertas_sdio: failed to find firmware (-2)
>>>>>>>>>>> [ 7.479794] ata1: SATA link down (SStatus 0 SControl F300)
>>>>>>>>>>> dracut-initqueue[85]: Warning: Could not boot.
>>>>>>>>>>> [ OK ] Mounted Configuration File System.
>>>>>>>>>>> [ OK ] Started Show Plymouth Boot Screen.
>>>>>>>>>>> [ OK ] Reached target Paths.
>>>>>>>>>>> [ OK ] Reached target Basic System.
>>>>>>>>>>> Gdracut-initqueue[85]: Warning: Could not boot.
>>>>>>>>>>> dracut-initqueue[85]: Warning: /dev/disk/by-label/rootfs does
>>>>>>>>>>> not
>>>>>>>>>>> exist
>>>>>>>>>>> Starting Dracut Emergency Shell...
>>>>>>>>>>> Warning: /dev/disk/by-label/rootfs does not exist
>>>>>>>>>>> Generating "/run/initramfs/rdsosreport.txt"
>>>>>>>>>>> Entering emergency mode. Exit the shell to continue.
>>>>>>>>>>> Type "journalctl" to view system logs.
>>>>>>>>>>> You might want to save "/run/initramfs/rdsosreport.txt" to a
>>>>>>>>>>> USB
>>>>>>>>>>> stick or /boot
>>>>>>>>>>> after mounting them and attach it to a bug report.
>>>>>>>>>>> dracut:/#
>>>>>>>>>>>> On Sep 21, 2015, at 2:34 AM, Jacco Ligthart
>>>>>>> <[email protected]>
>>>>>>>>>>>> wrote:
>>>>>>>>>>>>> On 09/20/15 19:18, Ioan Stan wrote:
>>>>>>>>>>>>> Hi Jacco,
>>>>>>>>>>>>> Really appreciated. Before proceeding, I'd like to confirm
>>>>>>>>>>>>> the
>>>>>>>>>>>>> steps (assuming similar procedure as for F18 in the link
>>>>>>>>>>>>> below)
>>>>>>>>>>>>> 1. xzcat dream* /dev/sdb (if the SD card is sdb; or use dd)
>>>>>>>>>>>>> 2. Configure u-boot (one that supports ext2)
>>>>>>>>>>>>> printenv
>>>>>>>>>>>>> set bootargs 'console=ttyS0,115200 root=LABEL=rootfs
>>>>>>>>>>>>> rootwait'
>>>>>>>>>>>>> set loadInitrd 'ext2load usb 1:1 0x7400000 uInitrd'
>>>>>>>>>>>>> set loadImage 'ext2load usb 1:1 0x6400000 uImage'
>>>>>>>>>>>>> set bootcmd 'usb start; ${loadImage}; ${loadInitrd} ; bootm
>>>>>>>>>>>>> 0x6400000 0x7400000'
>>>>>>>>>>>>> saveenv
>>>>>>>>>>>>> boot
>>>>>>>>>>>> yes, that's also how I think it should work. The first
>>>>>>>>>>>> partition
>>>>>>>> in
>>>>>>>>>>>> the image is an ext2 partition with indeed the files uInitrd
>>>>>>>>>>>> and
>>>>>>>>>>>> uImage. These files come from a kernel-kirkwood of F18. I'm
>>>>>>>>>>>> not
>>>>>>>> sure
>>>>>>>>>>>> if the uboot things should reference usb if we really boot
>>>>>>>>>>>> from
>>>>>>>> SD,
>>>>>>>>>>>> but if this works for you right now for F18, it should be
>>>>>>> similar
>>>>>>>>>>>> for RSEL7.
>>>>>>>>>>>> Jacco
>>>>>> _______________________________________________
>>>>>> users mailing list
>>>>>> [email protected]
>>>>>> http://lists.redsleeve.org/mailman/listinfo/users
>>>>> _______________________________________________
>>>>> users mailing list
>>>>> [email protected]
>>>>> http://lists.redsleeve.org/mailman/listinfo/users
>>>> _______________________________________________
>>>> users mailing list
>>>> [email protected]
>>>> http://lists.redsleeve.org/mailman/listinfo/users
>>
>> _______________________________________________
>> users mailing list
>> [email protected]
>> http://lists.redsleeve.org/mailman/listinfo/users
> _______________________________________________
> users mailing list
> [email protected]
> http://lists.redsleeve.org/mailman/listinfo/users
_______________________________________________
users mailing list
[email protected]
http://lists.redsleeve.org/mailman/listinfo/users
