----- Original Message ----- > From: "Renchu Mathew" <[email protected]> > To: "Martin Perina" <[email protected]> > Cc: [email protected] > Sent: Thursday, January 22, 2015 2:39:43 PM > Subject: RE: [ovirt-users] Power Management config on Ovirt > > Hi Martin, > > > > Yes. The vdsm host.log is from node-02.
That's strange, I cannot find any call to fenceNode which should appear, if PM status is gathered. Eli, any idea? > I have checked the link and it says > we need to install the sever view management agent & net-snmp on the hosts. > Do we need to try this? How to install this on node? I used the below irmc > admin user. Not, AFAIK this is needed only from Clustersuite, but not for oVirt. But could you please execute this command on node-20 just to confirm that Fujitsu Primergy is communicating through IPMI: fence_ipmilan -a IP -l USER -p PASS -o status -v -P where IP is IPMI address (from the log it should be 192.168.1.114) USER and PASS please set according to you setup. Thanks Martin > > > > [cid:[email protected]] > > > > Regards > > > > Renchu Mathew | Sr. IT Administrator > > > > > > > > CRACKNELL DUBAI | P.O. Box 66231 | United Arab Emirates | T +971 4 > 3445417 | F +971 4 3493675 | M +971 50 7386484 > > ABU DHABI | DUBAI | LONDON | MUSCAT | DOHA | JEDDAH > > EMAIL [email protected] | WEB www.cracknell.com > > > > This email, its content and any files transmitted with it are intended solely > for the addressee(s) and may be legally privileged and/or confidential. If > you are not the intended recipient please let us know by email reply and > delete it from the system. Please note that any views or opinions presented > in this email do not necessarily represent those of the company. Email > transmissions cannot be guaranteed to be secure or error-free as information > could be intercepted, corrupted, lost, destroyed, arrive late or incomplete, > or contain viruses. The company therefore does not accept liability for any > errors or omissions in the contents of this message which arise as a result > of email transmission. > > > > > > -----Original Message----- > From: Martin Perina [mailto:[email protected]] > Sent: Thursday, January 22, 2015 4:49 PM > To: Renchu Mathew > Cc: [email protected] > Subject: Re: [ovirt-users] Power Management config on Ovirt > > > > Hi, > > > > according to [1] Fujitsu iRMC should be accessible using IPMI. > > Now, I looked at logs, but I cannot see any fenceNode exection in vdsm.log. > According to engine.log, host Node-02.cracknell.com was used as fence proxy. > Are you sure that vdsm.log is from this host? > > > > Thanks > > > > Martin > > > > [1] https://www.redhat.com/archives/linux-cluster/2010-January/msg00056.html > > > > > > ----- Original Message ----- > > > From: "Renchu Mathew" <[email protected]> > > > To: "Martin Perina" <[email protected]> > > > Cc: [email protected] > > > Sent: Thursday, January 22, 2015 12:37:51 PM > > > Subject: RE: [ovirt-users] Power Management config on Ovirt > > > > > > Hi Martin, > > > > > > Please find attached log files from engine and proxy host. Not sure > > > whether IPMI or which one can be used. It is Fujitsu iRMC port. I also > > > tried the rsb but same error. > > > > > > Can we configure Power management using Fujitsu iRMC? > > > > > > Thanks & Regards > > > > > > Renchu Mathew > > > > > > -----Original Message----- > > > From: Martin Perina [mailto:[email protected]] > > > Sent: Thursday, January 22, 2015 1:58 PM > > > To: Renchu Mathew > > > Cc: [email protected] > > > Subject: Re: [ovirt-users] Power Management config on Ovirt > > > > > > Hi, > > > > > > first of all are you sure that Fujitsu PRIMERGY is accessible using > > > IPMI protocol? If so, could you provide engine.log and also vdsm.log > > > from host that was used as fencing proxy? You can find out which host > > > is used as a proxy either in Events tab after you execute the test or in > > engine.log. > > > > > > Thanks > > > > > > Martin Perina > > > > > > ----- Original Message ----- > > > > From: "Renchu Mathew" <[email protected]> > > > > To: [email protected] > > > > Sent: Thursday, January 22, 2015 7:41:43 AM > > > > Subject: [ovirt-users] Power Management config on Ovirt > > > > > > > > > > > > > > > > Dear all, > > > > > > > > > > > > > > > > I am trying to configure power management on ovirt v3.5 > > > > (ovirt-node-iso-3.5.0.ovirt35.20140912.el6) and using two Fujitsu > > > > PRIMERGY > > > > RX2540 M1 as node hypervisor. I used Fujitsu iRMC port on power > > > > management configuration. The test gives a message “Test failed, > > > > argument of type ‘NoneType’ is not iterable” as below . Also tried > > > > rsb type as per redhat document. > > > > > > > > > > > > > > > > Fence-agents-3.1.5-35.el6_5.4.x86_64 is there on both nodes. Do we > > > > need to specify anything in Options? > > > > > > > > > > > > > > > > Please help me. > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > > Best Regards > > > > > > > > > > > > > > > > > > > > > > > > Renchu Mathew > > > > > > > > > > > > > > > > > > > > > > > > _______________________________________________ > > > > Users mailing list > > > > [email protected]<mailto:[email protected]> > > > > http://lists.ovirt.org/mailman/listinfo/users > > > > > > > > _______________________________________________ Users mailing list [email protected] http://lists.ovirt.org/mailman/listinfo/users
