>---- Mensaje original ----
>De : klaus.schmidin...@tvdr.de
>Fecha : 24/06/2014 - 18:23 (H)
>Para : vdr@linuxtv.org
>Asunto : Re: [vdr] Diseqc question
>
>On 24.06.2014 18:17, Antti Hartikainen wrote:
>> On Tue, Jun 24, 2014 at 06:02:31PM +0200, Jose Alberto Reguero wrote:
>>> El Martes, 24 de junio de 2014 17:22:08 Jose Alberto Reguero escribió:
>>>> El Martes, 24 de junio de 2014 16:47:57 Klaus Schmidinger escribió:
>>>>> On 24.06.2014 16:32, Jose Alberto Reguero wrote:
>>>>>> El Martes, 24 de junio de 2014 15:38:14 Klaus Schmidinger escribió:
>>>>>>> On 24.06.2014 13:45, Jose Alberto Reguero wrote:
>>>>>>>> El Martes, 24 de junio de 2014 13:25:15 Klaus Schmidinger escribió:
>>>>>>>>> On 24.06.2014 12:58, Jose Alberto Reguero wrote:
>>>>>>>>>> I have a double LNB. I have a stb without diseqc capabilities and I
>>>>>>>>>> want to use it with the default diseqc port A, and I want to use
>>>>>>>>>> vdr with the diseqc port B. It is that possible?
>>>>>>>>>
>>>>>>>>> Does this LNB point to two neighboring sat positions and have one
>>>>>>>>> cable connector, or does it point to only one sat position and
>>>>>>>>> have two cable connectors?
>>>>>>>>>
>>>>>>>>> Klaus
>>>>>>>>
>>>>>>>> It is only one sat position and two cable connectors.
>>>>>>>
>>>>>>> Then the next question is whether these two connectors are for the
>>>>>>> (separate) horizontal and vertical band, or whether they both provide
>>>>>>> all bands. In the latter case it should just work.
>>>>>>>
>>>>>>> Klaus
>>>>>>
>>>>>> Both provide all bands. They point to ASTRA 19.2E.
>>>>>>
>>>>>> I use this diseq.conf entries:
>>>>>>
>>>>>> S28.2E  11700 V  9750  t v W15 A W15 t
>>>>>> S28.2E  99999 V 10600  t v W15 A W15 T
>>>>>> S28.2E  11700 H  9750  t V W15 A W15 t
>>>>>> S28.2E  99999 H 10600  t V W15 A W15 T
>>>>>>
>>>>>> S19.2E  11700 V  9750  t v W15 B W15 t
>>>>>> S19.2E  99999 V 10600  t v W15 B W15 T
>>>>>> S19.2E  11700 H  9750  t V W15 B W15 t
>>>>>> S19.2E  99999 H 10600  t V W15 B W15 T
>>>>>>
>>>>>> (28.2E is just a fake entry)
>>>>>> But when I tune a channel with vdr, the stb lost the signal.
>>>>>
>>>>> If both connectors provide all bands, you shouldn't need the 'A/B'
>>>>> commands.
>>>>>
>>>>> Do you have a link to the specs of that LNB?
>>>>>
>>>>> Klaus
>>>>
>>>> It is a Opticum. I buy it in amazon.
>>>>
>>>> http://www.dipolnet.com/twin_lnb_opticum-orton_ltp-04h_premium_0_1db_A9842.h
>>>> tm
>>>>
>>>> Jose Alberto
>>>>
>>>>
>>>
>>> I did another test, and if both channels are vertical there are not 
>>> problems.
>>> But if the stb is in a vertical channel, and vdr is in a horizontal channel,
>>> the stb loose the signal.
>>>
>>
>> Sound like broken LNB to me, if both tuners have their own cable coming from 
>> the outputs of LNB.
>
>I'd say so, too.
> From the specs your configuration should work just fine.
>
>Klaus
>

No, the two cables go to a diseqc, and after the cable from the diseqc go to a 
amplifier with two outputs and each output go to a tuner. But the stb don't 
have diseqc capabilities. I am trying to configure the diseqc in the vdr part. 
It is posible?

Jose Alberto

_______________________________________________
vdr mailing list
vdr@linuxtv.org
http://www.linuxtv.org/cgi-bin/mailman/listinfo/vdr

Reply via email to