Richard,
You forgot the lights!
Sandy.

Sent from my iPhone

> On 27 Oct 2013, at 04:14, Richard Turner <[email protected]> wrote:
> 
> If you have the standscan assembled correctly, and have the opening facing 
> you, you should find a hole in the top of the box toward the front right.
> If you place the phone with the back facing camera pointed down through the 
> hole, the home button will be near the right side of the box. The side of the 
> phone with the volume controls will be closest to you.
> Then, place your document, face up, on the bottom of the box with the bottom 
> of the document lined up against the right side of the box and lined up 
> across the back of the box.
> There will be about a half inch or so qap between the top of the document and 
> the left side of the box.
> If all that makes sense, you should get a nearly perfect scan.
> HTH,
> 
> 
> Richard
> (Sent from Richard's iPod Touch 5th gen)
> 
>> On Oct 26, 2013, at 8:46 PM, John Diakogeorgiou <[email protected]> 
>> wrote:
>> 
>> I have Scan Stand but haven't had any success with it. Can you please
>> explain where  to place the phone on top of the box and how to place
>> the paper inside. Thanks!
>> 
>>> On 10/26/13, David Chittenden <[email protected]> wrote:
>>> I have written these instructions in the past, so suspect they are available
>>> in the archives.
>>> 
>>> Open Prizmo and prepare to take a photo of the page. Before taking the
>>> picture, ensure that the room is well-lit, but direct sunlight is not
>>> shining on the page. In other words, too little light shades the page such
>>> that the print cannot be detected. Too much light causes the white of the
>>> page to enhance and the print to disappear. Also, if your body, or the phone
>>> or arm is between the light source and the page, the shadow of your body or
>>> the phone can cause a dark area on the page that can make the print in that
>>> area disappear.
>>> 
>>> Next, the phone must be as flat to the plain of the page as possible. If the
>>> phone is tilted in any way, the print characters are changed visually. The
>>> closer letters become short and thick whilst the more distant characters
>>> become small and thin. In other words, OCR may not be able to recognise the
>>> text, or parts of the text.
>>> 
>>> The phone must be as straightly aligned to the edges of the paper as
>>> possible. The more skew (rotation) added to the image, the lower the ability
>>> of OCR to recognise the text. Though Prizmo is the most forgiving OCR app in
>>> this regard, it still requires less than about 5 degrees of skew, and the
>>> best recognition occurs when skew is 0.
>>> 
>>> When the picture is taken, the camera / phone must be completely still. Any
>>> movement of the camera causes the text to blur. This is known as jidder.
>>> 
>>> Note: when sighted people take pictures of text for OCR, they automatically
>>> compensate for all of the above. Even then, however, a light box works
>>> better. I personally use, and very highly recommend, the StandScan Pro from
>>> www.standscan.com
>>> to correct for all of the above issues and get almost perfect OCR
>>> conversions every time.
>>> 
>>> When not using the StandScan Pro:
>>> Lay the phone flat on the paper with the camera in the middle of the page.
>>> Note: the camera is in the upper right corner of the back of the iPhone when
>>> the iPhone display is facing you and the home button is at the bottom of the
>>> display. Make sure the four sides of the phone are aligned with the four
>>> edges of the paper.
>>> 
>>> There are four ways to take the image: double-tap on the take picture
>>> button, split-tap on the take picture button, press the volume up button, or
>>> press the volume up button on the headset if the headset is plugged in. It
>>> is very strongly advisable that the method which creates the least amount of
>>> jidder is used. Double-tap the take picture button, therefore, should never
>>> be done. This method will always create movement, no matter how lightly one
>>> brushes the screen. Even with the delay Prizmo has now added to help us
>>> blind folk, this method is still the least accurate for image capture / OCR.
>>> Pressing the volume up button, though seemingly should be the best method,
>>> gives mixed results. This is because force must be applied on the side of
>>> the phone which alters the phone's position in relation to the page. Being
>>> blind, we cannot correct for this when it happens. I do not use the headset,
>>> so cannot comment on its accuracy or how to stabilise the phone whilst using
>>> the headset volume-up button. Therefore, the best method for the most
>>> consistent results is using the split-tap. This is because, split-tap
>>> actually activates when the tapping finger is released from the display. The
>>> split-tap command actually holds until the second finger is removed, no
>>> matter how long it takes (as long as neither finger moves enough to trigger
>>> a movement-based command such as the rotor.
>>> 
>>> Without moving the phone on the page, lift the phone enough to place the
>>> ring fingers of both hands under the phone along the long edges. Do not
>>> block the camera lens with the right hand's finger. It is necessary that
>>> both hands are used because, it is not possible to feel drifting while
>>> lifting the phone with just one hand. With both hands, one still drifts a
>>> little, but it is easier to detect it. Press the middle fingers of both
>>> hands against the sides of the phone. These fingers pressing on both sides
>>> stabilises the phone to the hands. Press the thumbs to the bottom of the
>>> phone with less pressure than the middle fingers. When the phone is secure
>>> on the platform created by the fingers,
>>> 
>>> Locate the take picture button with one of your index fingers. The take
>>> picture button is above the home button. When the fingertip locates the take
>>> picture button, it remains still on the button. Now, the other index finger
>>> lightly touches the active display near the edge. This sets VO up for the
>>> split-tap command.
>>> 
>>> Slowly start lifting the phone as straight up from the page as possible.
>>> Listen for VO to say, auto focus. Most times, when this is said, the entire
>>> page is in focus. Occasionally, there is a block of text, or an image, in
>>> the middle of the page that the camera has focused on. If this is the case,
>>> keep lifting slowly until the second time VO says, auto focus. After one has
>>> taken many OCR images, one develops a feel for the approximate proper
>>> distance. In the beginning, take the picture at the first auto focus point
>>> to start getting that feel. If one goes up too high, start over on the page.
>>> By the time you start descending again, you will have drifted too far from
>>> the middle of the page for a complete page image.
>>> 
>>> When auto focus is announced, stop movement. wait a couple seconds to ensure
>>> you are no longer moving the phone. Slowly lift the second finger from the
>>> touchscreen to activate the take picture button, or if at the edge of the
>>> touchscreen, merely slide the finger away from the active area of the screen
>>> (this is what I do as it introduces the least amount of movement). Now,
>>> Prizmo will monitor the image until it detects no movement. It will then
>>> take the picture. Also, Prizmo now has tones to help guide the image. Use
>>> very slow movements when attempting to utilise these guidances. Note:
>>> because of the way we blind people tend to use sweeping movements, move like
>>> you are almost not moving; just like the way one explores the touchscreen
>>> display. When I start a free-scanning session, it usually takes me two or
>>> three pictures before I get a good image. After I have been scanning for a
>>> little while, I often get good images with my first picture per page.
>>> 
>>> After the image is captured, follow the prompts for recognition.
>>> 
>>> David Chittenden, MSc, MRCAA
>>> Email: [email protected]
>>> Mobile: +64 21 2288 288
>>> Sent from my iPhone
>>> 
>>>> On 27 Oct 2013, at 4:08, "rubyalphonse" <[email protected]> wrote:
>>>> 
>>>> Hello All, I need some one’s help regarding the App Prizmo. How does it
>>>> work, How to scan and get it read? I was taking picture thinking it will
>>>> read, but it says the text is not detected. I will still phygit with it,
>>>> till I learn, but I need help please. I will be much obliged to you.
>>>> Thanks in advance Ruby
>>>> --
>>>> You received this message because you are subscribed to the "VIPhone"
>>>> Google Group.
>>>> 
>>>> Post a new message to VIPhone by emailing [email protected].
>>>> 
>>>> Search and view the VIPhone archives by visiting
>>>> http://www.mail-archive.com/[email protected]/.
>>>> 
>>>> Reach the VIPhone owner and moderators by emailing
>>>> [email protected].
>>>> 
>>>> Unsubscribe and leave VIPhone by emailing
>>>> [email protected].
>>>> 
>>>> More VIPhone group options can be found by visiting
>>>> http://groups.google.com/group/viphone?hl=en.
>>>> ---
>>>> You received this message because you are subscribed to the Google Groups
>>>> "VIPhone" group.
>>>> To unsubscribe from this group and stop receiving emails from it, send an
>>>> email to [email protected].
>>>> For more options, visit https://groups.google.com/groups/opt_out.
>>> 
>>> --
>>> You received this message because you are subscribed to the "VIPhone" Google
>>> Group.
>>> 
>>> Post a new message to VIPhone by emailing [email protected].
>>> 
>>> Search and view the VIPhone archives by visiting
>>> http://www.mail-archive.com/[email protected]/.
>>> 
>>> Reach the VIPhone owner and moderators by emailing
>>> [email protected].
>>> 
>>> Unsubscribe and leave VIPhone by emailing
>>> [email protected].
>>> 
>>> More VIPhone group options can be found by visiting
>>> http://groups.google.com/group/viphone?hl=en.
>>> ---
>>> You received this message because you are subscribed to the Google Groups
>>> "VIPhone" group.
>>> To unsubscribe from this group and stop receiving emails from it, send an
>>> email to [email protected].
>>> For more options, visit https://groups.google.com/groups/opt_out.
>> 
>> -- 
>> You received this message because you are subscribed to the "VIPhone" Google 
>> Group.
>> 
>> Post a new message to VIPhone by emailing [email protected].
>> 
>> Search and view the VIPhone archives by visiting 
>> http://www.mail-archive.com/[email protected]/.
>> 
>> Reach the VIPhone owner and moderators by emailing 
>> [email protected].
>> 
>> Unsubscribe and leave VIPhone by emailing 
>> [email protected].
>> 
>> More VIPhone group options can be found by visiting 
>> http://groups.google.com/group/viphone?hl=en.
>> --- 
>> You received this message because you are subscribed to the Google Groups 
>> "VIPhone" group.
>> To unsubscribe from this group and stop receiving emails from it, send an 
>> email to [email protected].
>> For more options, visit https://groups.google.com/groups/opt_out.
> 
> -- 
> You received this message because you are subscribed to the "VIPhone" Google 
> Group.
> 
> Post a new message to VIPhone by emailing [email protected].
> 
> Search and view the VIPhone archives by visiting 
> http://www.mail-archive.com/[email protected]/.
> 
> Reach the VIPhone owner and moderators by emailing 
> [email protected].
> 
> Unsubscribe and leave VIPhone by emailing 
> [email protected].
> 
> More VIPhone group options can be found by visiting 
> http://groups.google.com/group/viphone?hl=en.
> --- 
> You received this message because you are subscribed to the Google Groups 
> "VIPhone" group.
> To unsubscribe from this group and stop receiving emails from it, send an 
> email to [email protected].
> For more options, visit https://groups.google.com/groups/opt_out.

-- 
You received this message because you are subscribed to the "VIPhone" Google 
Group.

Post a new message to VIPhone by emailing [email protected].

Search and view the VIPhone archives by visiting 
http://www.mail-archive.com/[email protected]/.

Reach the VIPhone owner and moderators by emailing 
[email protected].

Unsubscribe and leave VIPhone by emailing [email protected].

More VIPhone group options can be found by visiting 
http://groups.google.com/group/viphone?hl=en.
--- 
You received this message because you are subscribed to the Google Groups 
"VIPhone" group.
To unsubscribe from this group and stop receiving emails from it, send an email 
to [email protected].
For more options, visit https://groups.google.com/groups/opt_out.

Reply via email to