I have been simulating the Mizuno device and adjusting a piecewise linear 
ambient temperature function for several hours.   I felt that it was time for a 
short update.

In an earlier report I stated that the output power might be as much as 100 
watts, well I need to adjust that figure downwards somewhat to 60 watts.  This 
is because I did not see that the ambient began at 22.5 when the device was at 
23 degrees C.  I assumed that the system had stabilized before the pulses 
began.  Had this been true, the device would have settled to a temperature that 
was 2.05 degrees above the ambient before the test began.

With that inclusion as well as a piecewise linear fit to the ambient 
temperature function I made another more accurate run of the simulation.  This 
time I found the peak at the correct time and at the right temperature when 60 
watts of output power (add 4 watts for the pump also) was dissipated into the 
water.  That means that 40 watts of excess power appears to be generated by the 
device.  The ratio of output power to input power comes out at 3.0 at this 
point in time.  Jed measured 3.42 for this day Oct 21.

I am sure that I will continue to adjust the results as better data is applied. 
 I hope to add the actual ambient measurements instead of my crude linear 
section fit.

Dave

 

 

 

-----Original Message-----
From: David Roberson <[email protected]>
To: vortex-l <[email protected]>
Sent: Fri, Jan 16, 2015 11:24 am
Subject: Re: [Vo]:Jed's Results Look Good So Far


Thanks Gigi,

I am continuing to develop the model further and as I give it consideration I 
find that it may allow us to obtain a second, accurate backup calculation for 
Jed's original conclusions.  We appear to be able to enter known data, 
including the 20 watt drive pulse and the pump leakage power along with ambient 
temperature conditions into the model and obtain a well defined temperature 
versus time plot.

Your original model does a remarkable job of replicating the measured results 
from the point in time where it begins to model the linear system.  Now, I have 
figured a way to extend that initial time as far into the past as needed in 
order to determine the magnitude of the LENR power pulse.  To achieve that goal 
it is necessary to have reasonably accurate measurement data for the ambient 
temperatures over that entire time period.  I believe that Jed has that 
information available within his files.  Jed, can you verify that this is true?

According to the excellent work by Gigi, we have a model with a main basic time 
constant of 5.84 hours.  This is the dominate pole of the system and therefore 
we will need to operate back in time with the input data for a period at least 
3 time constants in order to obtain an accurate projection of the thermal 
behavior of the Mizuno device.   The really good news is that we should be able 
to begin our analysis at the beginning of a day just before the power pulses 
are applied and make a decision at the end of that same day (24 hours) with 
reasonable accuracy.

At each increment of time we will need the value of the ambient temperature and 
any applied power plus the assumed magnitude of the resulting response power of 
the LENR process.  We can include the 4 watts of leakage for the pump which 
Gigi has determined as just another input that is constant over the simulation 
period.  If the model works as it should then we will see good agreement 
between the water temperature over that entire time period and what the model 
predicts.

Obviously we will need to have accurate data of the initial conditions of the 
system, which in this case is the water temperature just prior to the first 
power pulse, in order to begin the simulation.

Regards,

Dave

 

 

 

-----Original Message-----
From: Gigi DiMarco <[email protected]>
To: vortex-l <[email protected]>
Sent: Fri, Jan 16, 2015 7:01 am
Subject: Re: [Vo]:Jed's Results Look Good So Far




Great
Your results look very meaningful, Dave.



We are still thinking about the problem of not uniform temperature across the 
reactor vessel just after the power pulse are applied, but it seems to me that 
you have solved them.

I hope to read the full report very soon.


GG



2015-01-16 5:29 GMT+01:00 David Roberson <[email protected]>:

I ran out of patience waiting for an input from Gigi and decided to construct a 
simple numerical model of the calorimeter used with the Mizuno test.  After 
playing around with it for a while using the thermal values derived by Gigi and 
his team, I have come to my first conclusion.  It is a bit early and I might 
find a glaring error somewhere with further analysis but felt it was reasonable 
to offer an interim report.

It is consistent with the model for the device to be generating an output power 
of 100 watts.  I have rounded the value off at this time until further research 
can pin point it more accurately.

Even if 4 watts of leakage is present due to the pump action, the calorimeter 
appears to be fairly immune to that input provided the ambient does not change 
more than 2 degrees during the test.

Again, this is a first pass result and subject to revision.

Dave





Reply via email to