Thanks for the information Jed.  Of course the average power is much less than 
the peak as would be expected.  When you drive the heating wire with 20 watts 
of power, you are producing a large number of joules of heat during the 500 
second period.  I believe you said that you get approximately 500 seconds * 20 
watts = 10000 joules per pulse on average.  With 3 pulses that means you get 
around 30000 joules.  The report actually lists 30794 on Oct 21 which is the 
day I am simulating.

Also on that day within your report you state that 105321 total joules is 
deposited within the complete system due to a combination of the drive power, 
pump power and excess power from the device.  This means that you have a ratio 
of output energy to input energy of 3.42.   I am simulating a ratio of 
approximately 3.0 at this time.  Perhaps the fact that I conveniently used the 
same time frame for the excess power as the drive is what is causing the 
confusion.  You are correct that the output energy is being produced throughout 
a much longer period of time than the 500 seconds of 20 watt drive itself.

If you have a method of determining the actual shape in time of the energy 
being released by the active LENR wire please give me that information.   I can 
not imagine it being only 3 watts instantaneous as you seem to be implying.  
That would suggest that the same number of joules in each second are constantly 
being generated throughout the pulse repetition period.  I would certainly 
think that as the structure cools down, less heat is generated.  And, if past 
experience is a guide then the rate of production falls off very quickly as the 
temperature drops.

So, the instantaneous power must be far greater than 3 watts peak.  If we can 
come up with a method of measuring the true behavior then I will gladly find a 
way to include that factor into my model.  I can also report total joules over 
the entire pulse periods if that makes better sense to you.  In that case my 
model now calculates that 90000 joules total are detected versus your 105321 
joules reported. 

As I have stated, the number I have posted thus far is going to be adjusted as 
more accurate information is included.   I felt that it was a reasonable plan 
to keep everyone informed somewhat periodically as the simulation is honed in 
and that is why I made the posting.  Gigi is working in parallel on some type 
of model and it makes sense for us to share information instead of waiting for 
many weeks until a cleaned up report is generated.  Do you agree?

I hope that this clarifies what I am reporting.  To recap, I am currently using 
your data from Oct. 21, 2014 to model the amount of heat generated by Mizuno's 
device during that day.  My model simulates the behavior of a linear 
differential equation acting upon the inputs that you have reported.  The 
initial condition that I am using is the temperature of the coolant water just 
prior to the application of the first 20 watt power pulse.  I am using the 4 
watt pump leakage power that Gigi has determined to be accurate.  I am 
including an improving set of ambient temperature data that you have measured 
to be present during the test period.   The effects due to the ambient are 
taken into account by the configuration used in defining the differential 
equation.

Then, since excess power and energy are generated by the device during a power 
pulse I am making an assumption of its equivalent value.  This value is then 
adjusted so that the final temperature of the coolant matches what you have 
reported at a particular time.  In this case it is at the point in time where 
the peak temperature is noted as you have done.

Gigi did an excellent job of determining the equivalent models of the thermal 
resistance and heat capacity of the Mizuno device from your data that I am 
using to define the coefficients of my differential equation.   I verified that 
his model matched in two independent cases.  The first was with the pump active 
and the second was when it failed.  After reviewing this remarkable degree of 
correlation between a split apart system and a combined one I became convinced 
that it will be possible to achieve an accurate model that can be used to 
verify excess heat production.

If you have any additional questions please post them so I can answer any 
concerns you might foster.  I believe the model is going to be extremely 
useful.  Besides, it is adding strong support to your report.  Of course, had 
it shown otherwise I would have reported that as well since the truth is what 
we all seek.

Dave

 

-----Original Message-----
From: Jed Rothwell <[email protected]>
To: vortex-l <[email protected]>
Sent: Fri, Jan 16, 2015 3:08 pm
Subject: Re: [Vo]:Jed's Results Look Good So Far



David Roberson <[email protected]> wrote:

 
In an earlier report I stated that the output power might be as much as 100 
watts, well I need to adjust that figure downwards somewhat to 60 watts.  


If it were 60 W, that would phenomenal. Input power is only 20 W. Anomalous 
heat peaks at about 3 W.




This time I found the peak at the correct time and at the right temperature 
when 60 watts of output power (add 4 watts for the pump also) . . .


4 W is more than the average output for the whole day!


 

That means that 40 watts of excess power appears to be generated by the device.


That is off by a factor of 10, at least.


 
  The ratio of output power to input power comes out at 3.0 at this point in 
time.  Jed measured 3.42 for this day Oct 21.



That is the ratio I found for energy over the entire day, not for power. And I 
did not measure that; I extrapolated based on how hot I suppose the reactor 
vessel got. I measured only 1.38.


I have no idea where your numbers come from.


- Jed




Reply via email to