I hope i'm missing something here, because this doesn't seem to work:
$ sudo wee_device --set-transmitter-type=1,10
Using configuration file /etc/weewx/weewx.conf
Using Vantage driver version 3.0.11 (weewx.drivers.vantage)
Proceeding will set channel 1 to type 10 (none), repeater: none, inactive.
Are you sure you want to proceed (y/n)? y
Transmitter type for channel 1 set to 10 (none), repeater: none, inactive.
$ sudo wee_device --set-transmitter-type=3,0
Using configuration file /etc/weewx/weewx.conf
Using Vantage driver version 3.0.11 (weewx.drivers.vantage)
Proceeding will set channel 3 to type 0 (iss), repeater: none, active.
Are you sure you want to proceed (y/n)? y
Transmitter type for channel 3 set to 0 (iss), repeater: none, active.
$ sudo wee_device --info
Using configuration file /etc/weewx/weewx.conf
Using Vantage driver version 3.0.11 (weewx.drivers.vantage)
Querying...
Davis Vantage EEPROM settings:
CONSOLE TYPE: Vantage Pro2
CONSOLE FIRMWARE:
Date: Nov 21 2016
Version: 3.63
CONSOLE SETTINGS:
Archive interval: 60 (seconds)
Altitude: 0 (foot)
Wind cup type: large
Rain bucket type: 0.01 inches
Rain year start: 1
Onboard time: 2018-10-31 13:04:40
CONSOLE DISPLAY UNITS:
Barometer: inHg
Temperature: degree_F
Rain: inch
Wind: mile_per_hour
CONSOLE STATION INFO:
Latitude (onboard): +37.6°
Longitude (onboard): -122.1°
Use manual or auto DST? AUTO
DST setting: N/A
Use GMT offset or zone code? GMT_OFFSET
Time zone code: N/A
GMT offset: -8.0 hours
Temperature logging: LAST
Retransmit channel: ON (255)
TRANSMITTERS:
Channel Receive Repeater Type
1 inactive none iss
2 active none (N/A)
3 active none (N/A)
4 active none (N/A)
5 active none (N/A)
6 active none (N/A)
7 active none (N/A)
8 active none (N/A)
RECEPTION STATS:
Total packets received: 0
Total packets missed: 0
Number of resynchronizations: 0
Longest good stretch: 0
Number of CRC errors: 0
BAROMETER CALIBRATION DATA:
Current barometer reading: 29.982 inHg
Altitude: 0 feet
Dew point: 40 F
Virtual temperature: 53 F
Humidity correction factor: 1.7
Correction ratio: 1.000
Correction constant: +0.000 inHg
Gain: 0.000
Offset: 10.000
OFFSETS:
Wind direction: +0 deg
Inside Temperature: +0.0 F
Inside Humidity: +0 %
Outside Temperature: +0.0 F
Outside Humidity: +0 %
On Wednesday, October 31, 2018 at 5:36:14 AM UTC-7, Thomas Keffer wrote:
>
> The documentation does not mention this, but the Vantage stations will
> allow only one ISS at a time. So, you must first shut off your existing ISS
> on channel 1, *then* set up channel 3.
>
> # Turn off channel 1 by setting the type to "10":
> wee_device --set-transmitter-type=1,10
> # Now turn on channel 3 with type 0 ("ISS"):
> wee_device --set-transmitter-type=3,0
>
> -tk
>
>
> On Tue, Oct 30, 2018 at 9:45 PM Josh Behrends <[email protected]
> <javascript:>> wrote:
>
>> Background:
>> I'm running weewx version 3.8.2-1
>> In my neighborhood I have at least two other neighbors who have Davis
>> stations which my Vantage Pro 2 console picks up. My ISS is set to
>> transmit on channel 3, and my console works perfectly with this
>> configuration. I also have a Davis Envoy with a USB DataLogger which is
>> what weewx is polling. Using wee_device I've attempted multiple times to
>> configure channel 3 as an ISS, and each time I run wee_device --info it
>> shows not configured. I also have weewx configured to poll Station 3
>> (iss_id = 3 in weewx.conf). When I run weewx I'm getting data from some
>> other station! So I'm at a loss as to what to do at this point...
>>
>> Here is an example of wee_device:
>>
>> $ sudo wee_device --set-transmitter-type=3,0
>> Using configuration file /etc/weewx/weewx.conf
>> Using Vantage driver version 3.0.11 (weewx.drivers.vantage)
>> Proceeding will set channel 3 to type 0 (iss), repeater: none, active.
>> Are you sure you want to proceed (y/n)? y
>> Transmitter type for channel 3 set to 0 (iss), repeater: none, active.
>>
>>
>> $ sudo wee_device --info
>> Using configuration file /etc/weewx/weewx.conf
>> Using Vantage driver version 3.0.11 (weewx.drivers.vantage)
>> Querying...
>> Davis Vantage EEPROM settings:
>>
>> CONSOLE TYPE: Vantage Pro2
>>
>> CONSOLE FIRMWARE:
>> Date: Nov 21 2016
>> Version: 3.63
>>
>> CONSOLE SETTINGS:
>> Archive interval: 60 (seconds)
>> Altitude: 0 (foot)
>> Wind cup type: large
>> Rain bucket type: 0.01 inches
>> Rain year start: 1
>> Onboard time: 2018-10-30 21:39:22
>>
>> CONSOLE DISPLAY UNITS:
>> Barometer: inHg
>> Temperature: degree_F
>> Rain: inch
>> Wind: mile_per_hour
>>
>> CONSOLE STATION INFO:
>> Latitude (onboard): +37.6°
>> Longitude (onboard): -122.1°
>> Use manual or auto DST? AUTO
>> DST setting: N/A
>> Use GMT offset or zone code? GMT_OFFSET
>> Time zone code: N/A
>> GMT offset: -8.0 hours
>> Temperature logging: LAST
>> Retransmit channel: ON (255)
>>
>> TRANSMITTERS:
>> Channel Receive Repeater Type
>> 1 inactive none iss
>> 2 active none (N/A)
>> 3 active none (N/A)
>> 4 active none (N/A)
>> 5 active none (N/A)
>> 6 active none (N/A)
>> 7 active none (N/A)
>> 8 active none (N/A)
>>
>> RECEPTION STATS:
>> Total packets received: 0
>> Total packets missed: 0
>> Number of resynchronizations: 0
>> Longest good stretch: 0
>> Number of CRC errors: 0
>>
>> BAROMETER CALIBRATION DATA:
>> Current barometer reading: 30.097 inHg
>> Altitude: 0 feet
>> Dew point: 50 F
>> Virtual temperature: 52 F
>> Humidity correction factor: 2.3
>> Correction ratio: 1.000
>> Correction constant: +0.000 inHg
>> Gain: 0.000
>> Offset: 10.000
>>
>> OFFSETS:
>> Wind direction: +0 deg
>> Inside Temperature: +0.0 F
>> Inside Humidity: +0 %
>> Outside Temperature: +0.0 F
>> Outside Humidity: +0 %
>>
>>
>> Here are all settings from the "Vantage" section of my
>> /etc/weewx/weewx.conf
>> [Vantage]
>> type = serial
>> port = /dev/ttyUSB0
>> host = 1.2.3.4
>> baudrate = 19200
>> tcp_port = 22222
>> tcp_send_delay = 0.5
>> iss_id = 3
>> timeout = 4
>> wait_before_retry = 1.2
>> max_tries = 4
>> model_type = 2
>> driver = weewx.drivers.vantage
>>
>>
>>
>> --
>> You received this message because you are subscribed to the Google Groups
>> "weewx-user" group.
>> To unsubscribe from this group and stop receiving emails from it, send an
>> email to [email protected] <javascript:>.
>> For more options, visit https://groups.google.com/d/optout.
>>
>
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
For more options, visit https://groups.google.com/d/optout.
