I didn't change batteries in receiver as such. I've previously converted it to Lipo and charges via USB connection to Pi. But I did disconnect and reconnect said battery. And yes, on at least one occurance I did wait 2 minutes. Done about every combination.
Doesn't beep when press down button for for seconds. Thanks. On Fri, 21 Aug 2020, 14:55 Andrew Milner, <[email protected]> wrote: > from memory I THINK that when you press the down button the icon starts to > flash and it beeps and then it is hunting for the transmitter. If it does > not beep it is not searching. Did you change the batteries in the > transmitter AND the console? Did you wait 2 minutes before reinserting new > batteries in the transmitter? You could also try with the console outside > closer to the transmitter - and the manual suggests doing this resync at > night. Otherwise maybe it has died a death ... RIP... > > > > On Friday, 21 August 2020 15:20:29 UTC+3, James Muirhead wrote: >> >> I lost my manual aeons ago, have downloaded. It's on it's 10th (ish) set >> of batteries now! >> >> I tried to press down arrow for 4 seconds, but has no effect (backlight >> goes off, about it). >> >> I tried to remove batteries for about 30 minutes yesterday (so I could >> give whole thing a good clean). And they died at some point in middle of >> night anyhow. >> >> Manual also says it will attempt to reconnect every hour, and I've so far >> left it for almost a whole day and still no connection. >> >> Any other ideas? >> >> Many thanks. >> >> On Fri, 21 Aug 2020, 05:07 Andrew Milner, <[email protected]> wrote: >> >>> read the manual - there is a button to press (i forget which) to regain >>> communications. Just looked - press and hold the down key for 4 seconds >>> until the console beeps. >>> >>> Register transmitter If no outdoor weather data is displayed or the >>> signal to the sensors is lost during setting up, mounting, changing of >>> batteries to the sensor or plugging or unplugging cables, simply press and >>> hold the DOWN/- key for 4 seconds and a short beep will sound to >>> synchronize the base station to sensors. Without being synchronized, >>> weather data will not be received. NOTE: Wait two minutes before re-insert >>> the batteries of transmitter for proper reset. Note: The best condition for >>> reception is at night, between midnight and 6:00am – when there is less >>> atmospheric interference. >>> >>> >>> >>> On Thursday, 20 August 2020 21:10:43 UTC+3, James Muirhead wrote: >>>> >>>> My WH1080 sender / receiver appears to have died. >>>> >>>> The battery low indicator had been on for some time and died about 0130 >>>> this morning. >>>> >>>> I changed out the batteries in the sender today and it does not want to >>>> communicate with the receiver now. LED in the sender comes on and receiver >>>> appears normal. >>>> >>>> I've reset receiver and sender in both orders and left for an hour, >>>> etc, etc. WeeWX WebUI shows no signal (but I don't know how this is >>>> generated). >>>> >>>> The communication icon on receiver comes up sporadically for a minute >>>> at start and for quarter of a second once in a while. >>>> >>>> I'm gonna take apart the sender tomorrow and give everything a good >>>> clean, see if it helps. >>>> >>>> Has anyone got a suggestion, other than "buy a new weather station"? >>>> >>>> Thanks. >>>> >>>> PS - WeeWX is working perfectly. But I have WeeWX installed on an >>>> Orange Pi PC (1.3GHz Quad, 1GB RAM). Shout if you want anymore information. >>>> >>> -- >>> You received this message because you are subscribed to a topic in the >>> Google Groups "weewx-user" group. >>> To unsubscribe from this topic, visit >>> https://groups.google.com/d/topic/weewx-user/ySocUy01e_M/unsubscribe. >>> To unsubscribe from this group and all its topics, send an email to >>> [email protected]. >>> To view this discussion on the web visit >>> https://groups.google.com/d/msgid/weewx-user/7cffbaeb-c08c-4ddc-b0cc-ce4cda005b6do%40googlegroups.com >>> <https://groups.google.com/d/msgid/weewx-user/7cffbaeb-c08c-4ddc-b0cc-ce4cda005b6do%40googlegroups.com?utm_medium=email&utm_source=footer> >>> . >>> >> -- > You received this message because you are subscribed to a topic in the > Google Groups "weewx-user" group. > To unsubscribe from this topic, visit > https://groups.google.com/d/topic/weewx-user/ySocUy01e_M/unsubscribe. > To unsubscribe from this group and all its topics, send an email to > [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/32d5f35a-9cda-4fb4-b153-3bf907ea8575o%40googlegroups.com > <https://groups.google.com/d/msgid/weewx-user/32d5f35a-9cda-4fb4-b153-3bf907ea8575o%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/CAL93hP_J%3DDDBYOPL9BVP8hysw6PnyA_1%2B7zNeFBjezO198XQzg%40mail.gmail.com.
