The Envoy is functionally identical to the VP2, which is why it reports itself as a VP2. I'm not as confident about the WLIP, but I think it's the same way.
On Sat, May 14, 2022 at 8:52 PM Ryan Stasel <[email protected]> wrote: > so I have another Envoy, and a Weatherlink IP... and I'm trying to get it > configured, but for some reason, the Envoy (and Weatherlink) are convinced > I have a Vantage Pro2... setting it to a Vue it complains that it found a > Pro... =/ > > Ticket in with Davis support, but would be curious if anyone else has seen > this. > > On Saturday, May 14, 2022 at 4:59:54 AM UTC-7 Ryan Stasel wrote: > >> hmm. weewx (possibly) has no lead to the MB crashing twice. so going to >> flip back to ambientweatherapi extension for a bit until I can figure >> out... >> >> Thank you sir! >> >> On Friday, May 13, 2022 at 3:04:28 PM UTC-7 Ryan Stasel wrote: >> >>> 1. totally fair. guessing he's not going to agree. lol. On MB you just >>> say "Vantage" and that covers Pro, Pro2, Vue, and Envoy. >>> 3. I'm still seeing in weewx generated HTML on occasion an "Unknown" for >>> batt info (after changing archive interval to 5mins). It seemed like those >>> were in LOOP packets rather than LOOP2 (or possibly other way around), >>> which is why I set to 3 (both). I figured it was the HTML was being >>> generated after a LOOP packet that didn't include that info, so it was just >>> outputting unknown. >>> >>> On Friday, May 13, 2022 at 2:14:06 PM UTC-7 [email protected] wrote: >>> >>>> 1. Yours is a non-standard setup. I'd rather that the MB dev fixed his >>>> implementation. >>>> >>>> 2. That makes sense. >>>> >>>> 3. With a 60 second archive interval, it's possible that the console >>>> will occasionally not have seen the battery info, so it shows as N/A. With >>>> a 5 minute interval, it should consistently show a value. >>>> >>>> >>>> >>>> On Fri, May 13, 2022 at 10:27 AM Ryan Stasel <[email protected]> wrote: >>>> >>>>> Thanks Thomas. debug shows: >>>>> >>>>> May 13 10:21:22 raspi-server-misc weewx[6626] DEBUG >>>>> weewx.drivers.vantage: Opened up ethernet host 10.0.6.22 on port 22222. >>>>> timeout=4.0, tcp_send_delay=0.5 >>>>> May 13 10:21:22 raspi-server-misc weewx[6626] DEBUG >>>>> weewx.drivers.vantage: Gentle wake up of console successful >>>>> May 13 10:21:23 raspi-server-misc weewx[6626] DEBUG >>>>> weewx.drivers.vantage: Hardware type is 16 >>>>> May 13 10:21:25 raspi-server-misc weewx[6626] DEBUG >>>>> weewx.drivers.vantage: ISS ID is 1 >>>>> May 13 10:21:25 raspi-server-misc weewx[6626] DEBUG >>>>> weewx.drivers.vantage: Hardware name: Vantage Pro2 >>>>> >>>>> So confirmed there. =/ I've inquired with the MB dev to see if we can >>>>> be more specific. I think the MB emulates the LOOP protocol. Any chance we >>>>> could get some (possibly hidden) option to force the station type in the >>>>> Vantage driver? the biggest issue right now is weewx is expecting ET data >>>>> since it's a Vantage Pro2, but not getting it. >>>>> >>>>> For 2. I had the MB set, and therefore the console, set to 60 second >>>>> record time. Which was overriding the 300 sec in weewx, so the "noise" was >>>>> just 60 second record times vs the standard 300. Got that fixed by setting >>>>> MB to set the console to 5 mins. >>>>> >>>>> For 3. That makes sense. I set those to hardware rather than prefer. >>>>> It is still set to use both, I guess I'm curious one over the other. >>>>> Should >>>>> I just use 2? 2 doesn't seem to include battery info. I do notice that >>>>> with >>>>> it set to "3" (both) sometimes when weewx does it's web render it doesn't >>>>> have battery data (just Unknown) until the next time around when it >>>>> apparently gets that info and fills it in. What's best practice here? Just >>>>> use 2 and change the settings back to prefer_hardware and let weewx fill >>>>> in >>>>> the blanks? >>>>> Thanks! >>>>> On Thursday, May 12, 2022 at 9:09:17 PM UTC-7 [email protected] wrote: >>>>> >>>>>> 1. The hardware type is determined by the WRD command. You can check >>>>>> what it's returning by setting debug=1, then restarting. Look at the log. >>>>>> The hardware type will be listed and look something like: >>>>>> >>>>>> May 12 15:22:59 nuc weewx[91691] DEBUG weewx.drivers.vantage: >>>>>> Hardware type is 16 >>>>>> >>>>>> For whatever reason, yours must be returning 16, the code for the >>>>>> VantagePro series. >>>>>> >>>>>> The option "model_type" is used only to differentiate between the >>>>>> original VantagePro, and the current VantagePro2. It is always set to 2 >>>>>> for >>>>>> a Vue. >>>>>> >>>>>> 2. Not sure what you mean by 'noise'. Your plots look pretty normal >>>>>> to me. Perhaps your Vue has better resolution than your old station? >>>>>> >>>>>> 3. WeeWX will calculate various derived variables if they are not >>>>>> supplied by your hardware. LOOP and LOOP2 include different types in >>>>>> their >>>>>> packets, most notably 'pressure' and 'altimeter', so it is possible you >>>>>> would be switching between hardware and software origins. Personally, I >>>>>> would pick one or the other. >>>>>> >>>>>> -tk >>>>>> >>>>>> >>>>>> On Wed, May 11, 2022 at 9:33 AM Ryan Stasel <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> Thanks Thomas. I was looking through the Vantage driver, and was >>>>>>> curious if there was a way to just "force" Vue. Saw something about >>>>>>> setting >>>>>>> the value to 17, but not sure that is accurate. Does it read that value >>>>>>> out >>>>>>> of the Envoy EEPROM? I can inquire with the MB developer and see if they >>>>>>> have any thoughts. Since you tell the MB what station you have, seems >>>>>>> like >>>>>>> it should be able to report that back to Weewx. >>>>>>> >>>>>>> One thing I do notice is there's a significant amount of "noise" in >>>>>>> the graphs since switching over. If you take a look here: >>>>>>> https://www.staze.org/weewx/ before about 2pm PDT when it'll roll >>>>>>> off the graphs... maybe that's just the expected behavior with the LOOP >>>>>>> data. >>>>>>> >>>>>>> Also, random, I set it to use both LOOP and LOOP2, and there's a >>>>>>> note about setting to hardware for the values weewx would otherwise >>>>>>> calculate. Those are currently set to "prefer_hardware". I assume that >>>>>>> means it's still going to calculate on every packet that doesn't contain >>>>>>> that data, so I should hard set to "hardware"? Maybe that'll remove the >>>>>>> noise? Or is this also an MB side effect? >>>>>>> >>>>>>> On Tuesday, May 10, 2022 at 6:18:38 PM UTC-7 [email protected] wrote: >>>>>>> >>>>>>>> 1. I'm afraid I can't offer an opinion on this, because your >>>>>>>> arrangement is so non-standard. Normally, the station type is read out >>>>>>>> of >>>>>>>> EEPROM. >>>>>>>> 2. After 30 days, the logic in the skin gives up and figures the >>>>>>>> sensors are gone. So, you can either wait that long, or pare down the >>>>>>>> list >>>>>>>> of sensors in skin.conf. Look under stanza [DisplayOptions]. >>>>>>>> >>>>>>>> On Tue, May 10, 2022 at 12:52 PM Ryan Stasel <[email protected]> >>>>>>>> wrote: >>>>>>>> >>>>>>>>> Hi All, >>>>>>>>> >>>>>>>>> I just flipped drivers to the Vantage driver (having previously >>>>>>>>> used the ambientweatherapi driver). I have two questions. >>>>>>>>> >>>>>>>>> 1. My page now thinks I have a Vantage Pro 2 rather than a Vue. >>>>>>>>> I'm interfacing over "ethernet" to a Meteobridge Nano SD in an Envoy. >>>>>>>>> Is >>>>>>>>> there a different value I should put in for "model_type" to reflect >>>>>>>>> Vantage >>>>>>>>> Vue? >>>>>>>>> >>>>>>>>> 2. The ambientweatherapi driver reported battery level, and the >>>>>>>>> Vantage one does not. But now I just have two "Unknown" values where >>>>>>>>> those >>>>>>>>> go. I assume just clear out those DB entires so the template doesn't >>>>>>>>> render >>>>>>>>> them? Will have to figure out what field it used for this so I can >>>>>>>>> null it >>>>>>>>> out... >>>>>>>>> >>>>>>>>> Thanks! >>>>>>>>> >>>>>>>>> -- >>>>>>>>> You received this message because you are subscribed to the Google >>>>>>>>> Groups "weewx-user" group. >>>>>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>>>>> send an email to [email protected]. >>>>>>>>> To view this discussion on the web visit >>>>>>>>> https://groups.google.com/d/msgid/weewx-user/cb9428de-0583-4b64-bc94-a86a65702922n%40googlegroups.com >>>>>>>>> <https://groups.google.com/d/msgid/weewx-user/cb9428de-0583-4b64-bc94-a86a65702922n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>>>>>> . >>>>>>>>> >>>>>>>> -- >>>>>>> You received this message because you are subscribed to the Google >>>>>>> Groups "weewx-user" group. >>>>>>> To unsubscribe from this group and stop receiving emails from it, >>>>>>> send an email to [email protected]. >>>>>>> >>>>>> To view this discussion on the web visit >>>>>>> https://groups.google.com/d/msgid/weewx-user/8339cdba-6cf5-4e46-98cf-7cdfcfe773f3n%40googlegroups.com >>>>>>> <https://groups.google.com/d/msgid/weewx-user/8339cdba-6cf5-4e46-98cf-7cdfcfe773f3n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>>>> . >>>>>>> >>>>>> -- >>>>> You received this message because you are subscribed to the Google >>>>> Groups "weewx-user" group. >>>>> To unsubscribe from this group and stop receiving emails from it, send >>>>> an email to [email protected]. >>>>> >>>> To view this discussion on the web visit >>>>> https://groups.google.com/d/msgid/weewx-user/9e85c652-9cb0-4203-9cfd-5a852be38872n%40googlegroups.com >>>>> <https://groups.google.com/d/msgid/weewx-user/9e85c652-9cb0-4203-9cfd-5a852be38872n%40googlegroups.com?utm_medium=email&utm_source=footer> >>>>> . >>>>> >>>> -- > You received this message because you are subscribed to the Google Groups > "weewx-user" group. > To unsubscribe from this group and stop receiving emails from it, send an > email to [email protected]. > To view this discussion on the web visit > https://groups.google.com/d/msgid/weewx-user/31940e33-fe29-491d-9734-6db92a0ca349n%40googlegroups.com > <https://groups.google.com/d/msgid/weewx-user/31940e33-fe29-491d-9734-6db92a0ca349n%40googlegroups.com?utm_medium=email&utm_source=footer> > . > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion on the web visit https://groups.google.com/d/msgid/weewx-user/CAPq0zEBYFa9K5XESS5DmAw-qtTzLfA3BE%2Bm_mhw2XoEmnBOfAg%40mail.gmail.com.
