Thanks guys, I switched now to GW1000 Driver. Test driver also seems to be
looking quite good.
Is there any chance to add the rain data in the database? I had 15.3mm rain
yesterday, which is also the week, month and year totatl, since I started
the weather station on tuesday night.
[image: rain.PNG]
vince schrieb am Mittwoch, 4. Juni 2025 um 23:08:17 UTC+2:
In case you switch to the nice gw1000 driver via Ian's link, here's my old
config for my WS85 which is similar to your WS90, as well as the
incantation to test the driver interactively. Be a little forewarned this
was quite a while ago and I decommissioned the ecowitt haptic sensor
because it wasn't too accurate, but the weewx setup did work as I recall.
Your paths vs. the example --test-driver below will vary if you did a dpkg
installation.
[GW1000]
# This section is for the Ecowitt Gateway driver.
# How often to poll the API, default is every 20 seconds:
poll_interval = 20
# The driver to use:
driver = user.gw1000
ip_address = 192.168.2.87 # gw1200
port = 45000
[[field_map_extensions]]
outTempBatteryStatus = wh26_batt
batteryStatus1 = wh31_ch1__batt
batteryStatus2 = wh31_ch2__batt
batteryStatus3 = wh31_ch3__batt
batteryStatus4 = wh31_ch4__batt
batteryStatus5 = wh31_ch5__batt
batteryStatus8 = wh51_ch1__batt
soilTemp1 = temp9 # wh34
######batteryStatus8 = wh34_ch1__batt
rain = p_rain
stormRain = p_rainevent
rainRate = p_rainrate
dayRain = p_rainday
weekRain = p_rainweek
monthRain = p_rainmonth
yearRain = p_rainyear
windBatteryStatus = ws85_batt
# PYTHONPATH=~/weewx/src python3 ~/weewx-data/bin/user/gw1000.py
--test-driver --ip-address=192.168.2.87
# 2024-08-30 11:01:19 PDT (1725040879): 'dateTime': '1725040879',
'daymaxwind': '2.9', 'extraHumid1': '56', 'extraHumid2': '54',
'extraHumid3': '56', 'extraHumid4': '59', 'extraHumid5': '70',
'extraTemp1': '23.3', 'extraTemp2': '22.2', 'extraTemp3': '22.1',
'extraTemp4': '22.0', 'extraTemp5': '21.8', 'extraTemp9': '17.8',
'inHumidity': '53', 'inTemp': '22.5', 'outHumidity': '77', 'outTemp':
'19.5', 'p_dayRain': '0.0', 'p_monthRain': '34.3', 'p_rain': 'None',
'p_rainRate': '0.0', 'p_stormRain': '0.0', 'p_weekRain': '1.0',
'p_yearRain': '42.4', 'pressure': '1006.5', 'relbarometer': '1006.5',
'soilMoist1': '41', 'usUnits': '17', 'wh31_ch1_batt': '0', 'wh31_ch1_sig':
'4', 'wh31_ch2_batt': '0', 'wh31_ch2_sig': '4', 'wh31_ch3_batt': '0',
'wh31_ch3_sig': '4', 'wh31_ch4_batt': '0', 'wh31_ch4_sig': '4',
'wh31_ch5_batt': '0', 'wh31_ch5_sig': '4', 'wh32_batt': '0', 'wh32_sig':
'4', 'wh51_ch1_batt': '1.4', 'wh51_ch1_sig': '4', 'windDir': '280',
'windGust': '1.2', 'windSpeed': '1.1', 'wn34_ch1_batt': '1.5',
'wn34_ch1_sig': '4', 'ws85_batt': '3.08', 'ws85_sig': '4'
On Wednesday, June 4, 2025 at 2:01:24 PM UTC-7 Steeple Ian wrote:
There is a fork of the GW1000 driver here which was synced with Gary's main
branch just before he went 'off air'. It is a better bet than the
Interceptor driver. I have GW1000, GW2000 and GW3000 devices and they all
wrk perfectly.
https://github.com/Millardiang/weewx-gw1000
On Wednesday, June 4, 2025 at 10:37:53 PM UTC+2 Markus Lösch wrote:
Also after some rain now, nothing shows up at rain. There is also nothing
written down in the database…
Anyone that can help?
chin0x schrieb am Mittwoch, 4. Juni 2025 um 14:47:06 UTC+2:
Hey guys,
I've been going through some discussions but not quite sure if I did
everything rigth.
Due to the circumstances that the GW1000 Driver is all of a sudden not
available anymore, I decided to use the Interceptor driver when I changed
from "Simulation" to "Productive" mode yesterday evening.
I found out that the rain is not available in the database and saw some
discussions about it.
What I now did was adding some values to the Interceptor Stanza in the
weewx.conf:
[Interceptor]
driver = user.interceptor
device_type = ecowitt-client
port = 8000
[[sensor_map_extensions]]
rain = drain_piezo
rainRate = rrain_piezo
supplyVoltage = wh90batt
referenceVoltage = ws90cap_volt
But it shows me no rain in my skins. Currently it is not raining, but there
was rain this morning. Is the data only filling the actuall rain into the
database or also the data from this morning? If not from this morning, how
can I insert that data afterwards ?
in the log it shows me the following entries:
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter runtime=80319
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter heap=94012
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter vpd=0.071
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter rrain_piezo=0.000
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter erain_piezo=0.157
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter hrain_piezo=0.008
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter drain_piezo=0.157
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter wrain_piezo=0.157
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter mrain_piezo=0.157
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter yrain_piezo=0.157
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter srain_piezo=1
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter ws90cap_volt=2.5
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter ws90_ver=155
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter wh90batt=3.14
Jun 4 14:46:10 weewx weewxd[1727]: INFO user.interceptor: unrecognized
parameter interval=16
so rain is showing some values here...
--
You received this message because you are subscribed to the Google Groups
"weewx-user" group.
To unsubscribe from this group and stop receiving emails from it, send an email
to [email protected].
To view this discussion visit
https://groups.google.com/d/msgid/weewx-user/95aa9ed3-1846-4a2f-82c7-9c673fe06e09n%40googlegroups.com.
