6313 has nothing that can work with weewx. I need a weatherlink to make it work.
There is nothing currently that can get data from the weatherlink.com API v2. There is something in git, but it's heavily modified and needs some serious work to work with native weewx. On Friday, October 16, 2026 at 9:18:43 PM UTC-5 Mark Jenks wrote: > Thanks everyone for the comments! I just ordered the new Davis and will > see how it goes. :) > > I was concerned without the direct connect USB. > > > On Friday, October 16, 2026 at 11:58:53 AM UTC-5 weather list wrote: > >> On Oct 16, 2026, at 12:36, Greg Troxel <[email protected]> wrote: >> > >> > weather list <[email protected]> writes: >> > >> >> I've been using two Meteobridge Nano SD's for years, with no issues >> >> with a VP2, in two separate places. Connects wirelessly, and there are >> >> a lot of built-in reports and weather site uploads right in the MB >> >> firmware. Pays to be sure your devices have router-assigned IP's and >> >> that the power supplies are reliable. But they are indeed pricey.... >> > >> > Is there a weewx driver, so that you can run weewx and have it get data >> > from the meteobridge? Can it use some API on the MB to backfill the >> > database from old data, assuming the meteobridge stayed up on batteries >> > and the computer didn't? >> > >> > Not having good answers to those questions is what I meant by quirks. >> >> I use the weewx vantage driver set for ethernet. But I am not sure there >> is a backfill provision, though the micro SD card stores data. >> >> Vantage stanza in weewx.conf >> >> [Vantage] >> # This section is for the Davis Vantage series of weather stations. >> >> # Connection type: serial or ethernet >> # serial (the classic VantagePro) >> # ethernet (the WeatherLinkIP or Serial-Ethernet bridge) >> type = ethernet >> >> # If the connection type is serial, a port must be specified: >> # Debian, Ubuntu, Redhat, Fedora, and SuSE: >> # /dev/ttyUSB0 is a common USB port name >> # /dev/ttyS0 is a common serial port name >> # BSD: >> # /dev/cuaU0 is a common serial port name >> # port = /dev/ttyUSB0 >> >> # If the connection type is ethernet, an IP Address/hostname is required: >> host = 192.168.1.14 >> >> ###################################################### >> # The rest of this section rarely needs any attention. >> # You can safely leave it "as is." >> ###################################################### >> >> # Serial baud rate (usually 19200) >> baudrate = 19200 >> >> # TCP port (when using the WeatherLinkIP) >> tcp_port = 22222 >> >> # TCP send delay (when using the WeatherLinkIP): >> # tcp_send_delay = 0.5 >> >> # The type of LOOP packet to request: 1 = LOOP1; 2 = LOOP2; 3 = both >> loop_request = 1 >> >> # The id of your ISS station (usually 1). If you use a wind meter >> connected >> # to a anemometer transmitter kit, use its id >> iss_id = 1 >> >> # How long to wait for a response from the station before giving up (in >> # seconds; must be greater than 2) >> timeout = 10 >> >> # How long to wait before trying again (in seconds) >> wait_before_retry = 5 # 1.2 >> >> # How many times to try before giving up: >> max_tries = 8 >> >> # Vantage model Type: 1 = Vantage Pro; 2 = Vantage Pro2 >> model_type = 2 >> >> # The driver to use: >> driver = weewx.drivers.vantage > > -- You received this message because you are subscribed to the Google Groups "weewx-user" group. To unsubscribe from this group and stop receiving emails from it, send an email to [email protected]. To view this discussion visit https://groups.google.com/d/msgid/weewx-user/9c515636-db6d-4049-ae48-088deb283eabn%40googlegroups.com.
