It would seem to have many of the same virtues as the enclosure we use. I've used some pretty heavy plastic enclosures to protect APs from baseballs, basketballs, etc., in gymnasiums. Those were fiberglass reinforced polyethylene, and resulted in very little attenuation. I know ABS is a common radome material, so I would expect the loss to be lower still, probably a fraction of a dB. You could contact Oberon to find out for sure. They're very RF savvy, so I'm sure it's something they considered.
-----Original Message----- From: The EDUCAUSE Wireless Issues Constituent Group Listserv [mailto:[EMAIL PROTECTED] On Behalf Of Johnson, Bruce T Sent: Thursday, April 17, 2008 5:51 PM To: [email protected] Subject: Re: [WIRELESS-LAN] WAP Enclosures Chuck, What are your thoughts about this enclosure, also from Oberon. I am told the Cisco 1250 APs can be supported with the 1240 AP brackets, and since this enclosure doesn't require antenna holes, should work for hardware upgrades. It uses a rectangular plastic dome cover. Does anyone know how much RF attenuation is introduced with plastic covers? http://www.oberonwireless.com/WebDocs/1059%20Spec%20Sheet.pdf -----Original Message----- From: The EDUCAUSE Wireless Issues Constituent Group Listserv [mailto:[EMAIL PROTECTED] On Behalf Of Chuck Enfield Sent: Thursday, April 17, 2008 5:37 PM To: [email protected] Subject: Re: [WIRELESS-LAN] WAP Enclosures I'm a little late to the discussion, as usual, but I'm very happy with our enclosure. It lays on the grid in place of a 2'x2' tile, has a mounting plate that is predrilled and threaded for a wide assortment of APs, and comes with eyelets for the code-required drop wires Jim mentioned in his email starting the thread. They make installation a snap. We use the Oberon Model 1050-00. It's basically the same as the one at this link, http://www.oberonwireless.com/WebDocs/1052%20Spec%20Sheet.pdf, but it comes with the universal mounting plate. They also have models with strategically located holes or plastic domes for integral antennas if that's what your AP requires. While I'm on the topic, Oberon also sells some low-profile antennas that look quite nice on this enclosure. Scott, if you see a surge in sales after this post, I expect a cut. ;-) The point about expense is well taken, but I think it's important from an RF standpoint to get the antennas below the ceiling and I think this enclosure looks far better than wall-mounted APs in most cases. The enclosure's contribution to security will vary based on the other measures you have in place. It would be easy to remove the enclosure with the AP in it, but it would be hard to conceal. If you have video surveillance, the enclosure will definitely make it harder to get out of the building without being spotted. We haven't lost any to theft yet. (Knock on wood!) Is it more secure than hiding the APs above the ceiling? Your guess is as good as mine. While it's likely that getting rid of enclosures will make you less likely to be caught violating the building code, it's not necessarily a formula for compliance. If your jurisdiction relies on the 2005 NEC, the conventional interpretation is that nothing other than the ceiling itself can be supported by the ceiling tiles, grid, or drop wire. You'll have to mount the AP (and even the antennas) to a wall, uni-strut, cable tray, etc, above the ceiling, or support it with a dedicated drop wire. Prior to 2005, that restriction only applied when the drop ceiling was necessary for the building's fire rating. If your jurisdiction relies on an earlier version of the NEC (I understand some jurisdictions still reference the 1996 code), you can get away with using the ceiling components for support in most cases. The 2008 NEC is out, but I haven't had time to check if those restrictions have been relaxed at all. Chuck Enfield Sr. Communications Engineer Penn State University Telecommunications & Networking Services 110 USB2, UP, PA 16802 Ph. (814) 863-8715 Fx. (814) 865-3988 -----Original Message----- From: The EDUCAUSE Wireless Issues Constituent Group Listserv [mailto:[EMAIL PROTECTED] On Behalf Of Frank Kirstein Sent: Tuesday, April 15, 2008 10:57 AM To: [email protected] Subject: Re: [WIRELESS-LAN] WAP Enclosures For the most part, we do not use enclosures unless it's in a low hanging area. We used the Panduit enclosures for a couple of APs just about a month ago. They were least costly that I could find. Lee H Badman wrote: > We have also decided against enclosures for two reasons: cost and > aesthetics. Having mostly standardized on the Cisco 1130 for a/g, the > form-factor is close enough to that of smoke heads and other devices > that they are far easier on the eye than the typical enclosure. And > has been stated here by others, the enclosures can often add half > again or more to the per-AP cost. When we did our dorms and student > apartments 100% last year, we put hundreds and hundreds of APs within > reach of potential theft, some ended up in student rooms out of > necessity. To date, we have lost 1. > > But- as we look at 11n and weigh options, I hope that the major > players hear the call for APs that aren't obviously and visually antenna laden. > These are probably easier targets versus "low profile" APs, mounting > candidate locations are reduced, and they are a tougher sell to very > particular architects and space planners. > > -Lee Badman > > > -----Original Message----- > From: The EDUCAUSE Wireless Issues Constituent Group Listserv on > behalf of Hector J Rios > Sent: Mon 4/14/2008 11:28 AM > To: [email protected] > Subject: Re: [WIRELESS-LAN] WAP Enclosures > > I agree with Michael. The "added" security provided by the enclosures > doesn't justify the cost. Most of our APs are installed above ceiling. > Locations where we do not have false ceiling, we put the APs high > enough where they cannot be reach. In the 9 years we've had wireless, > we've had > 4 APs stolen. Paying for the replacement is way cheaper. Currently we > have a little over 1500 APs installed. > > Hector > > -----Original Message----- > From: The EDUCAUSE Wireless Issues Constituent Group Listserv > [mailto:[EMAIL PROTECTED] On Behalf Of Michael > Kaegler > Sent: Monday, April 14, 2008 9:45 AM > To: [email protected] > Subject: Re: [WIRELESS-LAN] WAP Enclosures > > We stopped using them. > > There are no moving parts, so we don't need dust protection. > All of the current generation of APs are plenum. > > And security: If the AP is on top of the drop ceiling, out of sight, > then its out of mind. In our environment we don't need any additional > security (As evidenced by the fact that we haven't had a single loss > even in student dorm buildings, even ones where we had to place the AP > on the bare wall inside the student broom closets!). We do use the > integrated (although not exactly hardened) locking mechanism on the > Cisco 1232/1242 APs. In some situations we use kenningston-style cable > locks. > -porkchop > > > At 9:50 AM -0400 4/14/08, Jim Gogan wrote: > >I'm curious to know what other campuses are doing in regards to > >ceiling enclosures for access points. > > > >We've been using PANDUIT-PZXIFIED and PANDUIT-PZW2X2DCB ceiling > >enclosure hardware but our Facilities folks and our Infrastructure > >Engineering folks in conversations with the State Building Code > >officers have determined that the labor/installation costs for those > >enclosures are now going to go up (see below) and, well suffice it to > >say, when it gets to the point that the enclosures themselves start > >to get closer in cost to the APs, you gotta wonder. > > > >Would be interested to hear what others are doing in this regard. > >Thanks in advance. > > > > -- > Michael "Porkchop" Kaegler, Sr. Network Analyst > (845) 575-3061 Marist College, Poughkeepsie, NY > > ********** > Participation and subscription information for this EDUCAUSE > Constituent Group discussion list can be found at http://www.educause.edu/groups/. > > ********** > Participation and subscription information for this EDUCAUSE > Constituent Group discussion list can be found at http://www.educause.edu/groups/. > > ********** Participation and subscription information for this > EDUCAUSE Constituent Group discussion list can be found at > http://www.educause.edu/groups/. ********** Participation and subscription information for this EDUCAUSE Constituent Group discussion list can be found at http://www.educause.edu/groups/. ********** Participation and subscription information for this EDUCAUSE Constituent Group discussion list can be found at http://www.educause.edu/groups/. The information transmitted in this electronic communication is intended only for the person or entity to whom it is addressed and may contain confidential and/or privileged material. Any review, retransmission, dissemination or other use of or taking of any action in reliance upon this information by persons or entities other than the intended recipient is prohibited. If you received this information in error, please contact the Compliance HelpLine at 800-856-1983 and properly dispose of this information. ********** Participation and subscription information for this EDUCAUSE Constituent Group discussion list can be found at http://www.educause.edu/groups/. ********** Participation and subscription information for this EDUCAUSE Constituent Group discussion list can be found at http://www.educause.edu/groups/.
