Eh? What ya mean???
-----Original Message----- From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Philip Dorr Sent: Friday, September 24, 2010 9:14 PM To: WISPA General List Subject: Re: [WISPA] UBNT Nano5M Secondary RJ45 Port PoE Burnout! It works perfectly fine if you power through the secondary port. On Fri, Sep 24, 2010 at 8:05 PM, RickG <rgunder...@gmail.com> wrote: > I was skeptical of the poe passthrough sicne I first saw it and this is why. > On repeaters, it would be so tempting to just run one wire but I've > stuck with two. It will be interesting to see if it gets fixed. Thanks > for sharing! > > On Fri, Sep 24, 2010 at 8:50 PM, Robert West > <robert.w...@just-micro.com> > wrote: >> >> Today I finally figured out an Issue I’ve been having with a >> NanoStation5M. I have a customer who wanted service, was in trees >> but had a hot signal out at the road. Dug a 4 foot hole, put in 2 10 >> foot sections of rigid conduit and 5 bags of concrete. Ran an >> underground line of Cat5e, double shielded and flooded cable with >> ground wire to his house. That was 5 months or so ago. At the >> beginning of August, he called me and said his neighbor wanted >> service. Same trees so I took the AirGrid down, put up a Nano5M and >> plugged a Nano loco2 into the secondary port and shot it at a second >> Nano Loco2 at his place. Replaced my weird Airgrid >> >> >> >> Worked perfectly, everyone happy. 2 weeks ago I get a call, neighbor >> not working. I go out, no power light on the Nano at the pole. I >> figure, bad crimp……. Take it down, make up a new wire to connect the two, >> fires up. >> All good. 2 days later, same issue. I reset it all to defaults, >> reconfigure, all okay. 2 days later, same thing. I downgrade >> firmware to 5.2. Couple of days later, no signal again. I’ll also >> add I was getting some “weird” lag at the AP that this setup was >> feeding off of. So I was fighting two battles. Then today, I find >> that the PoE Pass Through check box is empty. DUH! I check it, >> apply, comes back empty. I do it again, same issue. I go out and I >> can connect my laptop through the secondary port but it will not give any >> voltage. >> >> >> >> I checked my lag time issue at the AP. GONE! >> >> >> >> I then checked in the UBNT forums…………. It’s an issue. After 20 days >> PoE on the secondary Nano port starts to die. Replaced it with >> another Nano5M, working fine but looks like I’ll be coming up with >> another MacGyver solution to service this dude………. >> >> >> >> Just so ya knows. >> >> >> >> Bob- >> >> >> >> >> >> >> >> >> >> >> >> --------------------------------------------------------------------- >> ----------- >> WISPA Wants You! Join today! >> http://signup.wispa.org/ >> >> --------------------------------------------------------------------- >> ----------- >> >> WISPA Wireless List: wireless@wispa.org >> >> Subscribe/Unsubscribe: >> http://lists.wispa.org/mailman/listinfo/wireless >> >> Archives: http://lists.wispa.org/pipermail/wireless/ > > > > > ---------------------------------------------------------------------- > ---------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > ---------------------------------------------------------------------- > ---------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/