Nope. No dice. Played with it after I took it down. Did a hard reset then............. PoE is always on no matter what the checkbox says. Before reset, PoE did not work no matter which port power was put into.
Downgraded, upgraded, just can't turn that sucker off. Maybe I need to show it a picture of my first wife..............! Bob- -----Original Message----- From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] On Behalf Of Philip Dorr Sent: Saturday, September 25, 2010 9:38 AM To: WISPA General List Subject: Re: [WISPA] UBNT Nano5M Secondary RJ45 Port PoE Burnout! input power in the "secondary" port and use the "main" port to power the second radio On Fri, Sep 24, 2010 at 8:39 PM, Robert West <robert.w...@just-micro.com> wrote: > Eh? What ya mean??? > > > -----Original Message----- > From: wireless-boun...@wispa.org [mailto:wireless-boun...@wispa.org] > On Behalf Of Philip Dorr > Sent: Friday, September 24, 2010 9:14 PM > To: WISPA General List > Subject: Re: [WISPA] UBNT Nano5M Secondary RJ45 Port PoE Burnout! > > It works perfectly fine if you power through the secondary port. > > On Fri, Sep 24, 2010 at 8:05 PM, RickG <rgunder...@gmail.com> wrote: >> I was skeptical of the poe passthrough sicne I first saw it and this is why. >> On repeaters, it would be so tempting to just run one wire but I've >> stuck with two. It will be interesting to see if it gets fixed. >> Thanks for sharing! >> >> On Fri, Sep 24, 2010 at 8:50 PM, Robert West >> <robert.w...@just-micro.com> >> wrote: >>> >>> Today I finally figured out an Issue I’ve been having with a >>> NanoStation5M. I have a customer who wanted service, was in trees >>> but had a hot signal out at the road. Dug a 4 foot hole, put in 2 >>> 10 foot sections of rigid conduit and 5 bags of concrete. Ran an >>> underground line of Cat5e, double shielded and flooded cable with >>> ground wire to his house. That was 5 months or so ago. At the >>> beginning of August, he called me and said his neighbor wanted >>> service. Same trees so I took the AirGrid down, put up a Nano5M and >>> plugged a Nano loco2 into the secondary port and shot it at a second >>> Nano Loco2 at his place. Replaced my weird Airgrid >>> >>> >>> >>> Worked perfectly, everyone happy. 2 weeks ago I get a call, >>> neighbor not working. I go out, no power light on the Nano at the >>> pole. I figure, bad crimp……. Take it down, make up a new wire to connect >>> the two, fires up. >>> All good. 2 days later, same issue. I reset it all to defaults, >>> reconfigure, all okay. 2 days later, same thing. I downgrade >>> firmware to 5.2. Couple of days later, no signal again. I’ll also >>> add I was getting some “weird” lag at the AP that this setup was >>> feeding off of. So I was fighting two battles. Then today, I find >>> that the PoE Pass Through check box is empty. DUH! I check it, >>> apply, comes back empty. I do it again, same issue. I go out and I >>> can connect my laptop through the secondary port but it will not give any >>> voltage. >>> >>> >>> >>> I checked my lag time issue at the AP. GONE! >>> >>> >>> >>> I then checked in the UBNT forums…………. It’s an issue. After 20 >>> days PoE on the secondary Nano port starts to die. Replaced it with >>> another Nano5M, working fine but looks like I’ll be coming up with >>> another MacGyver solution to service this dude………. >>> >>> >>> >>> Just so ya knows. >>> >>> >>> >>> Bob- >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> >>> -------------------------------------------------------------------- >>> - >>> ----------- >>> WISPA Wants You! Join today! >>> http://signup.wispa.org/ >>> >>> -------------------------------------------------------------------- >>> - >>> ----------- >>> >>> WISPA Wireless List: wireless@wispa.org >>> >>> Subscribe/Unsubscribe: >>> http://lists.wispa.org/mailman/listinfo/wireless >>> >>> Archives: http://lists.wispa.org/pipermail/wireless/ >> >> >> >> >> --------------------------------------------------------------------- >> - >> ---------- >> WISPA Wants You! Join today! >> http://signup.wispa.org/ >> --------------------------------------------------------------------- >> - >> ---------- >> >> WISPA Wireless List: wireless@wispa.org >> >> Subscribe/Unsubscribe: >> http://lists.wispa.org/mailman/listinfo/wireless >> >> Archives: http://lists.wispa.org/pipermail/wireless/ >> > > > ---------------------------------------------------------------------- > ---------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > ---------------------------------------------------------------------- > ---------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ > > > > ---------------------------------------------------------------------- > ---------- > WISPA Wants You! Join today! > http://signup.wispa.org/ > ---------------------------------------------------------------------- > ---------- > > WISPA Wireless List: wireless@wispa.org > > Subscribe/Unsubscribe: > http://lists.wispa.org/mailman/listinfo/wireless > > Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/ -------------------------------------------------------------------------------- WISPA Wants You! Join today! http://signup.wispa.org/ -------------------------------------------------------------------------------- WISPA Wireless List: wireless@wispa.org Subscribe/Unsubscribe: http://lists.wispa.org/mailman/listinfo/wireless Archives: http://lists.wispa.org/pipermail/wireless/
