>Have you had any situation where a Tranzeo worked at a customer site and >Ubiquiti didn't?
Having that right now. MT RB411 AP with XR2. UBNT Nanstation M2 Connection rate all over the place and on a video stream drops clear down to 3.3M with 45% CCQ. Throw a OLD Tranzeo CPG-19 at the site and get a solid 48 MB 90% CCQ. I have seen this on this sector mostly and it was all replaced in DEC due to ICE getting in the RB case. May Climb in a week or two and Change to a Rocket with a new 120* sector. But you asked Josh. Yep I have had it. Steve Barnes General Manager PCS-WIN / RC-WiFi -----Original Message----- From: [email protected] [mailto:[email protected]] On Behalf Of Josh Luthman Sent: Thursday, February 23, 2012 11:53 AM To: WISPA General List Subject: Re: [WISPA] [Ubnt_users] Ubiquity Rocket M2 with Tranzeo CPE >Might have to start drinking the ubiquity koolaid. I've just not had >good luck with the ones I've tried out here. Have you had any situation where a Tranzeo worked at a customer site and Ubiquiti didn't? I replaced my Tranzeo stuff with Mikrotik way back before Ubiquiti had their stuff. I doubt I will ever use a Tranzeo radio again. Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Thu, Feb 23, 2012 at 11:49 AM, Marlon K. Schafer (509-982-2181) <[email protected]> wrote: > I can't help with the Ubiquity issue, but your CPE situation is the > same as ours. I know Mikrotik works well with them. > > Once you get something working well you'll love the new AP's! > > I do wish Tranzeo would fix the danged lockup issues on the cpe's though. > Some people never have trouble, others do weekly. ug > > Might have to start drinking the ubiquity koolaid. I've just not had > good luck with the ones I've tried out here. > marlon > > ----- Original Message ----- > From: "Matt Hoppes" <[email protected]> > To: "Ubiquiti Users Group" <[email protected]> > Cc: <[email protected]>; <[email protected]> > Sent: Monday, February 20, 2012 4:06 PM > Subject: Re: [WISPA] [Ubnt_users] Ubiquity Rocket M2 with Tranzeo CPE > > >> Did you install the RF Armor shield kits? They are an incredible >> help at defeating noise. >> >> >> >> On Feb 20, 2012, at 14:47, Jay DeBoer <[email protected]> wrote: >> >>> I am in process of converting a tower from Tranzeo AP's to Ubquity >>> Rocket M2's. I have the M2's hung and pointed. I can get the >>> clients to connect but I seem to be getting half throughput at best. >>> >>> I have the Airmax disabled on the M2's and the Clients have been >>> running in 802.11b mode previously. >>> >>> The clients are a mix of Tranzeo CPQ and SL2 radios. Signal levels >>> appear to be a bout the same if not a little better. My noise floor >>> has seem to come up from around -100 to -95/90ish. >>> >>> At this point I'm a little lost / too frustrated to think straight. >>> Any suggestions would be appreciated. >>> >>> Thank you. >>> >>> -- >>> Jay DeBoer >>> >>> Chief Engineer >>> Summit Digital Holdings, Inc. >>> 100 N Roland St, Suite B >>> McBain, MI 49657 >>> >>> Office: 231-825-2500 >>> Direct: 231-908-0033 >>> Fax: 231-908-0039 >>> [email protected] >>> >>> _______________________________________________ >>> Ubnt_users mailing list >>> [email protected] >>> http://lists.wispa.org/mailman/listinfo/ubnt_users >> _______________________________________________ >> Wireless mailing list >> [email protected] >> http://lists.wispa.org/mailman/listinfo/wireless > > _______________________________________________ > Wireless mailing list > [email protected] > http://lists.wispa.org/mailman/listinfo/wireless _______________________________________________ Wireless mailing list [email protected] http://lists.wispa.org/mailman/listinfo/wireless _______________________________________________ Wireless mailing list [email protected] http://lists.wispa.org/mailman/listinfo/wireless
