Update
I found WSJT-X v1.7 & installed on Linux Mint. I got it to work but sound
output is very low. I cant get enough audio to give power out on TX.
I cant find any where to turn up the audio on Linux Mint. I adjusted audio
settings on the rig but still not enough to get the watt meter level to show
power out on the rig or external watt meter.
73 Eddy N4ABN
Get Outlook for iOS<https://aka.ms/o0ukef>
________________________________
From: signalhz signalhz <[email protected]>
Sent: Tuesday, February 28, 2017 8:15:38 PM
To: WSJT software development
Subject: Re: [wsjt-devel] IC-7300 USB-D --> IC-7300 control lost
I have similar problems
I cant get WSJT-X v 1.1, r3496 to work using rig control while on Linux Mint
18.1 64 bit 'Serena' & cant get any audio to the programs from the USB Codec. I
get "Failed to start audio input stream. " & "PortAudio says requested sound
card format not supported. I am using Timewave Navigator. I don't see Icom 7300
in the drop down list for rig control. I am not real familiar with Linux Mint
yet.
I have FlDigi working fine on Linux
Now on Windows some reason WSJT-X loses audio to TX some times but not often. I
have to close the program & re-open it to get audio back.
Help would be appreciated.
73 Eddy N4ABN
Get Outlook for iOS<https://aka.ms/o0ukef>
_____________________________
From: Pino Zollo <[email protected]<mailto:[email protected]>>
Sent: Tuesday, February 28, 2017 4:01 PM
Subject: [wsjt-devel] IC-7300 USB-D --> IC-7300 control lost
To: <[email protected]<mailto:[email protected]>>
Hi Bill,
El 28/02/17 a las 15:45,
[email protected]<mailto:[email protected]>
escribió:
> what version of WSJT-X are you using?
1.7.0 last version distributed via PPA on Mint 17.3
>
> The WSJT-X "Settings->Radio->Mode" options determine if WSJT-X controls
> the mode of your rig and whether USB or USB-DATA mode is used.
>
Found the solution into the WSJT-X configuration....now it is stable in
USB-D.
> With Icom rigs you must disable "CI-V Transceive Mode" in the rig's
> menu, this option which is on by default causes unsolicited CAT traffic
> that can give unexpected and undesirable behaviour.
>
TU done...
> You should also do a basic RFI check by doing a test transmission into a
> dummy load or at least on minimum power on the rig. There have been a
> few reports of what appears to be RFI issues with the USB interface on
> the IC-7300.
The problem is present also in RX only, without TXing.
...after few minutes of operation the PC loses the control of the radio
and opens a window to ask for retry or leave.
...also the audio gets lost and I have to restart WSJT-x to get the
control again.
>
> 73
> Bill
> G4WJS.
Best 73
Pino ZP4KFX
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org<http://SlashDot.org>! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]<mailto:[email protected]>
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
------------------------------------------------------------------------------
Check out the vibrant tech community on one of the world's most
engaging tech sites, SlashDot.org! http://sdm.link/slashdot
_______________________________________________
wsjt-devel mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/wsjt-devel
