Hi Lee.....thanks...
i have had Xastir set up as you say for a long time BUT have never seen
it work as an I-gate in the way aprsg is at the present time.....
i know it should work and have tried to find out why not but i havent
got too much hair to keep pulling it out HI HI
73 David VK4BDJ
On 12/06/14 00:43, Lee Bengston wrote:
Hi David,
In Xastir, under File-Configure-Defaults in the menu, there is a section
labeled IGate Options. Check the box that says "Allow RF to Inet and Inet
to RF traffic", and click OK. Then under Interface-Interface Control in
the menu, select your AX25 interface and click the Properties button. The
same Igate options that are in the defaults menu are there. Check the same
box for RF to Inet and Inet to RF, and click OK. In the Inet to RF
direction, this will gate only messages.
Regards,
Lee - K5DAT
On Wed, Jun 11, 2014 at 12:07 AM, David <djm...@bigpond.com> wrote:
Hi Lee...i should have mentioned im using a AX25 tnc port as set out in
the HowTo:AX25 on the Xastir wiki
David
On 11/06/14 13:56, David wrote:
Hi Lee. i bow to your superior knowledge
i have aprsg running on Ubuntu 14.04 .....i have config it to do the same
as our other local I-gate which is off the air at this time..using FT-2800
to TNC-X
it takes messages from APRS-IS and TX to the local APRS repeater....
the incoming Igate area is limited to 1300 kms so that i dont flood the
repeater with too much signals.
I have heard that Xastir can IGATE but have only seen how to configure it
as a Digipeater...how can Xastir be set up to do what im doing with aprsg
73 David VK4BDJ
On 11/06/14 12:29, Lee Bengston wrote:
On Tue, Jun 10, 2014 at 7:16 PM, David <djm...@bigpond.com> wrote:
Hi.....agree that update would be good
ability to have an included igate that can be configured
to my knowledge linux only has 3 igate programs worth looking at
aprsg,aprx2,dixprs....the only one ive got working is aprsg....the other
two i cant get to work with a AX25 port and a TNC-x...at least i havent
got
the configs correct will keep trying.
Those are the small programs ideal for running "headless". I've tried
all 3 of them - aprsg is not good as a Tx Igate because it can't be
limited
to gate only messages to RF, which is standard. I like the format of the
text config file for aprsg - may have been a little easier than aprx or
dixprs, but I have been able to get all of them to work. Dixprs is a bit
tricky when you first try it with AX25 because the ax25 port is
referenced
as "ax0" or "ax1", etc. as the case may be instead of referencing the
name
of the ax25 interface in /etc/ax25/axports like other software does.
In Linux, Xastir already supports Igating, and so does YAAC.
JavAPRSIgate
also runs in Linux, which is an adjunct to javAPRSServr. Also aprsd
works
as an Igate, and APRSIS32 runs fine in wine, so Linux has a lot more
choices than those 3. I understand DireWolf also can Igate, but I've not
tried it.
Lee - K5DAT
_______________________________________________
Xastir mailing list
Xastir@lists.xastir.org
http://xastir.org/mailman/listinfo/xastir
_______________________________________________
Xastir mailing list
Xastir@lists.xastir.org
http://xastir.org/mailman/listinfo/xastir