Hi smithjohn,
The following command should do it
chtab node=node01 ipmi.bmcport=0
then run
nodeset node01 bmcsetup
then reboot your machine. Make sure that the machine reboots off the
network, and once it goes into the nbfs system, it should re-do the
ipmi/bmc on the node. Once the blue LED comes on, you should be able to
start using rpower/rcons again
I hope that helps,
regards,
Arf
On 29/05/12 16:28, smithjohn wrote:
hi,arfi,
first,thanks for your response very much.
I use the ethernet port ,and the speed of it is 1000Mb/s.
At the same time,I have the extra port , these are fibre ports,but
don't use it .
excuse me ,I couldn't understand what you say, sorry,
for example : you means add ipmi.bmcport=0 , but which table should
add .
could you mind have a demo for it ,thanks ,
By the way, before I update the CMOS, I can rpower node on,and it
can login the OS.
When the problem happen,I restore the default settings of CMOS,
then it also can rpower on and login
Last ,thanks again for your attention.
> From: [email protected]
> Date: Tue, 29 May 2012 12:30:48 +0100
> To: [email protected]
> Subject: Re: [xcat-user] xCAT 2.7.2 is released
>
> Hi smithjohn,
>
> Which network port is the NW cable in, and do you have any extra
> cables going into the IMM port?
>
> If you only have the one, then you need add ipmi.bmcport=0 for the
> configuration, so that the ipmi i.e. rpower and rcons works over the
> NW interface. What you may be seeing is that the configuration is
> actually taking place, but only dedicated on the IMM port. Once you
> make the modification, re-do the discovery process, and see if it goes
> to plan
>
> regards,
> --
> Arif Ali
>
> catch me on freenode IRC, username: arif-ali
>
>
> On 28 May 2012 20:45, smithjohn <[email protected]> wrote:
> > hi,lissa and everyone:
> > today, I still have the problem like what I had sent the mail
about the
> > upadate cmos
> > before,I fall across a problem like this: when I update the CMOS
of system
> > x3650 m4 ,the node doesn't on when I type command :"rpower node01
reset"
> > today,I update the CMOS of system x3550 M4 ,the problem still
happen.
> > so,if everyone who have way to solve this problem ,please share
with me
> > ,thanks very much ,much !
> >
> >
> > tips: this is the CMOS setting file: loaddefault BootOrder
> > loaddefault uEFI
> > set Processors.Hyper-Threading Disable
> > set BootOrder.BootOrder "Legacy Only=PXE Network=Hard Disk 0"
> > set DevicesandIOPorts.Com1FlowControl Hardware
> > set DevicesandIOPorts.Com1TerminalEmulation VT100
> > set DevicesandIOPorts.Com1ActiveAfterBoot Enable
> > set DevicesandIOPorts.SerialPortSharing Enable
> > set DevicesandIOPorts.SerialPortAccessMode Dedicated
> > set DevicesandIOPorts.RemoteConsole Enable
> > set DevicesandIOPorts.Slot1PCIeSpeed Gen3
> > set DevicesandIOPorts.Slot2PCIeSpeed Gen3
> > set DevicesandIOPorts.Slot3PCIeSpeed Gen3
> >
> > management node OS: RHELS6.2
> > XCAT firmware : 2.7.1
> >
> > thanks again!
> >
------------------------------------------------------------------------------
Live Security Virtual Conference
Exclusive live event will cover all the ways today's security and
threat landscape has changed and how IT managers can respond. Discussions
will include endpoint security, mobile security and the latest in malware
threats. http://www.accelacomm.com/jaw/sfrnl04242012/114/50122263/
_______________________________________________
xCAT-user mailing list
[email protected]
https://lists.sourceforge.net/lists/listinfo/xcat-user
