Hello Jessica: Thanks for your swift response, as per your suggestions i have downloaded yocto-eglibc-i586-powerpc-toolchain-sdk-0.9.tar.bz2 file from yocto website. I have installed the same. you can see now content of my /opt/poky folder as following
[sac...@sachinlinux yocto_tools]$ ls /opt/poky/ environment-setup-i586-poky-linux site-config-i586-poky-linux sysroots version-ppc603e-poky-linux environment-setup-ppc603e-poky-linux site-config-ppc603e-poky-linux version-i586-poky-linux [sac...@sachinlinux yocto_tools]$ But despite that i am getting same message [sac...@sachinlinux yocto_tools]$ poky-qemu zImage-2.6.34-qemuppc-0.9.bin yocto-image-minimal-qemuppc-0.9.rootfs.ext3 Set MACHINE to [qemuppc-0] based on kernel [zImage-2.6.34-qemuppc-0.9.bin] In order for this script to dynamically infer paths to kernels or filesystem images, you either need bitbake in your PATH or to source poky-init-build-env before running this script [sac...@sachinlinux yocto_tools]$ I do not which script this is referring. Please help me. Kind regards Sachin On Thu, Nov 11, 2010 at 7:59 AM, Zhang, Jessica <[email protected]>wrote: > Hi Sachin, > > First of all, if you want to run ppc, the toolchain you need to download is > yocto-eglibc-i586-powerpc-toolchain-sdk-0.9.tar.bz2. After you install it > under /opt/poky, you should go under /opt/poky and source the > environment-setup-ppc* and try start qemu again... > > Let us know if you still run into issues. > > Thanks, > Jessica > > ------------------------------ > *From:* [email protected] [mailto: > [email protected]] *On Behalf Of *sachin kumar > *Sent:* Wednesday, November 10, 2010 6:09 PM > *To:* [email protected] > *Subject:* [yocto] Problem in running poky-qemu > > Dear All: > > I am new to qemu, so please excuse me, i am asking basic question. > > Actually i want to run linux image for ppc on qemu. > > My host machine is running Fedora13. > > For that i have downloaded following from yocto project website. > > Disk Image: yocto-image-minimal-qemuppc-0.9.rootfs.ext3 > Kernel Image : zImage-2.6.34-qemuppc-0.9.bin > Toolchain: yocto-eglibc-i586-i586-toolchain-sdk-0.9.tar.bz2 > > Now toolchain was installed properly. > > Now when i am running poky-qemu from command line it is giving following > message > > ============================================================================================= > [r...@sachinlinux yocto_tools]# poky-qemu zImage-2.6.34-qemuppc-0.9.bin > yocto-image-minimal-qemuppc-0.9.rootfs.ext3 > Set MACHINE to [qemuppc-0] based on kernel [zImage-2.6.34-qemuppc-0.9.bin] > In order for this script to dynamically infer paths > to kernels or filesystem images, you either need > bitbake in your PATH or to source poky-init-build-env > before running this script > > > ============================================================================================= > I am blank about this message, which script they are referring. > Please help me for the same. > This will be a great help for me as i am at critical phase of one of my > project. > > Kind Regards > Sachin > > > > >
_______________________________________________ yocto mailing list [email protected] https://lists.yoctoproject.org/listinfo/yocto
