Hi: i am sorry, again i am getting same message.
Regards Sachin On 11/12/10, Zhang, Jessica <[email protected]> wrote: > Hi Sachin, > > under /opt/poky, can you do the following in exact sequence: > 1. source environment-setup-ppc603e-poky-linux > 2. poky-qemy qemuppc zImage-2.6.34.qemuppc-0.9.bin > yocto-image-minimal-qemuppc-0.9.rootfs.ext3 > > Thanks, > Jessica > > _____ > > From: [email protected] [mailto:[email protected]] On Behalf > Of sachin kumar > Sent: Thursday, November 11, 2010 8:19 AM > To: Zhang, Jessica > Cc: [email protected] > Subject: Re: [yocto] Problem in running poky-qemu > > > Hello Jessica: > > Thanks for your swift response, as per your suggestions i have downloaded > yocto-eglibc-i586-powerpc-toolchain-sdk-0.9.tar.bz2 file from yocto website. > I have installed the same. > you can see now content of my /opt/poky folder as following > > [sac...@sachinlinux yocto_tools]$ ls /opt/poky/ > environment-setup-i586-poky-linux site-config-i586-poky-linux > sysroots version-ppc603e-poky-linux > environment-setup-ppc603e-poky-linux site-config-ppc603e-poky-linux > version-i586-poky-linux > [sac...@sachinlinux yocto_tools]$ > > But despite that i am getting same message > > [sac...@sachinlinux yocto_tools]$ poky-qemu zImage-2.6.34-qemuppc-0.9.bin > yocto-image-minimal-qemuppc-0.9.rootfs.ext3 > Set MACHINE to [qemuppc-0] based on kernel [zImage-2.6.34-qemuppc-0.9.bin] > In order for this script to dynamically infer paths > to kernels or filesystem images, you either need > bitbake in your PATH or to source poky-init-build-env > before running this script > [sac...@sachinlinux yocto_tools]$ > > > I do not which script this is referring. > Please help me. > > Kind regards > > Sachin > > > > > > On Thu, Nov 11, 2010 at 7:59 AM, Zhang, Jessica <[email protected]> > wrote: > > > Hi Sachin, > > First of all, if you want to run ppc, the toolchain you need to download is > yocto-eglibc-i586-powerpc-toolchain-sdk-0.9.tar.bz2. After you install it > under /opt/poky, you should go under /opt/poky and source the > environment-setup-ppc* and try start qemu again... > > Let us know if you still run into issues. > > Thanks, > Jessica > > _____ > > From: [email protected] [mailto:[email protected]] > On Behalf Of sachin kumar > Sent: Wednesday, November 10, 2010 6:09 PM > To: [email protected] > Subject: [yocto] Problem in running poky-qemu > > > Dear All: > > I am new to qemu, so please excuse me, i am asking basic question. > > Actually i want to run linux image for ppc on qemu. > > My host machine is running Fedora13. > > For that i have downloaded following from yocto project website. > > Disk Image: yocto-image-minimal-qemuppc-0.9.rootfs.ext3 > Kernel Image : zImage-2.6.34-qemuppc-0.9.bin > Toolchain: yocto-eglibc-i586-i586-toolchain-sdk-0.9.tar.bz2 > > Now toolchain was installed properly. > > Now when i am running poky-qemu from command line it is giving following > message > ============================================================================ > ================= > [r...@sachinlinux yocto_tools]# poky-qemu zImage-2.6.34-qemuppc-0.9.bin > yocto-image-minimal-qemuppc-0.9.rootfs.ext3 > Set MACHINE to [qemuppc-0] based on kernel [zImage-2.6.34-qemuppc-0.9.bin] > In order for this script to dynamically infer paths > to kernels or filesystem images, you either need > bitbake in your PATH or to source poky-init-build-env > before running this script > > ============================================================================ > ================= > I am blank about this message, which script they are referring. > Please help me for the same. > This will be a great help for me as i am at critical phase of one of my > project. > > Kind Regards > Sachin > > > > > > > > _______________________________________________ yocto mailing list [email protected] https://lists.yoctoproject.org/listinfo/yocto
