Hi,
well. First: no, i don't have any usb cable or something like that. i
plug my usb dongle on the backside of my computer right into the usb hub
which is mounted directly on the motherboard.
Second: I applied the patch and recompiled the kernel + zd1211rw module
using ZD1211_DEBUG=y.
If i try to connect to my AP i get the following:
<----------- snip ----------->
[14:09 So Jun 11]
[EMAIL PROTECTED]:/usr/src/2.6.17-rc4-mm3/zd1211/zd1211_2006-06-07$ ifconfig
eth0 Link encap:Ethernet HWaddr 00:11:E2:02:XX:XX
inet addr:192.168.2.155 Bcast:192.168.2.255 Mask:255.255.255.0
UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1
RX packets:0 errors:0 dropped:0 overruns:0 frame:0
TX packets:0 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:1000
RX bytes:0 (0.0 b) TX bytes:0 (0.0 b)
lo Link encap:Local Loopback
inet addr:127.0.0.1 Mask:255.0.0.0
UP LOOPBACK RUNNING MTU:16436 Metric:1
RX packets:15 errors:0 dropped:0 overruns:0 frame:0
TX packets:15 errors:0 dropped:0 overruns:0 carrier:0
collisions:0 txqueuelen:0
RX bytes:1212 (1.1 Kb) TX bytes:1212 (1.1 Kb)
[14:09 So Jun 11]
[EMAIL PROTECTED]:/usr/src/2.6.17-rc4-mm3/zd1211/zd1211_2006-06-07$ iwconfig
lo no wireless extensions.
eth0 802.11g zd1211 ESSID:"WLAN"
Mode:Managed Frequency:2.442 GHz Access Point: 00:03:C9:A3:XX:XX
Bit Rate=11 Mb/s
Encryption key:XXXX-XXXX-XXXX-XXXX-XXXX-XXXX-XX Security
mode:restricted
Link Quality=93/100 Signal level=76/100
Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0
Tx excessive retries:0 Invalid misc:0 Missed beacon:0
[14:09 So Jun 11]
[EMAIL PROTECTED]:/usr/src/2.6.17-rc4-mm3/zd1211/zd1211_2006-06-07$ ping
192.168.2.1
PING 192.168.2.1 (192.168.2.1) 56(84) bytes of data.
ping: sendmsg: Operation not permitted
--- 192.168.2.1 ping statistics ---
1 packets transmitted, 0 received, 100% packet loss, time 0ms
<----------- snip ----------->
If i scan for APs i get the following:
<----------- snip ----------->
[14:07 So Jun 11]
[EMAIL PROTECTED]:/usr/src/2.6.17-rc4-mm3/zd1211/zd1211_2006-06-07$ iwlist eth0
scanning
eth0 Scan completed :
Cell 01 - Address: 00:03:C9:A3:XX:XX
ESSID:"WLAN"
Protocol:IEEE 802.11bg
Mode:Master
Channel:7
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=100/100 Signal level=100/100
Extra: Last beacon: 315ms ago
Cell 02 - Address: 00:03:C9:A3:XX:XX
ESSID:"<hidden>"
Protocol:IEEE 802.11bg
Mode:Master
Channel:7
Encryption key:on
Bit Rates:1 Mb/s; 2 Mb/s; 5.5 Mb/s; 6 Mb/s; 9 Mb/s
11 Mb/s; 12 Mb/s; 18 Mb/s; 24 Mb/s; 36 Mb/s
48 Mb/s; 54 Mb/s
Quality=100/100 Signal level=100/100
Extra: Last beacon: 61ms ago
<----------- snip ----------->
The AP uses a hidden essid which is just "WLAN". The two found Access
Points are obviously the same.
So ... i can't ping my AP nor connecting to it's web front-end.
Strange thing. The route is set, but arp tells:
<----------- snip ----------->
Address HWtype HWaddress Flags
Mask Iface
192.168.2.1 <incomplete>
<----------- snip ----------->
Bye
Christian
Daniel Drake wrote:
> Ulrich Kunitz wrote:
>> On 06-06-10 22:09 C.S: wrote:
>>
>>> here some output to make things clear:
>>> zd1211rw 2-3:1.0: error ioread32(CR_REG1): -11
>>
>> It looks like, that you have IO problems on the USB bus. Do you use
>> cable to connect the device? How about using another cable?
>
> There are no IO problems. The error code is generated by the driver:
> -EWOULDBLOCK.
>
> The issue is that shared key auth was broken/incomplete in softmac. I
> recently fixed this.
>
> http://marc.theaimsgroup.com/?l=linux-netdev&m=114917251329206&q=raw
>
> Daniel
>
___________________________________________________________
Gesendet von Yahoo! Mail - Jetzt mit 1GB Speicher kostenlos - Hier anmelden:
http://mail.yahoo.de
_______________________________________________
Zd1211-devs mailing list - http://zd1211.ath.cx/
Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
