Hi! If I use the vendor based community driver (zd1211.ath.cx/wiki/ vendorbaseddriver), use the zd1211b support in Makefile, an do as on page described I get:
[dmesg] eth0: no IPv6 routers present ZD1211B - http://zd1211.ath.cx/ - r85 Based on www.zydas.com.tw driver version 2.5.0.0 usb 2-1: reset high speed USB device using ehci_hcd and address 2 Release Ver = 4810 zd1211:bulk out: wMaxPacketSize = 200 zd1211:bulk in: wMaxPacketSize = 200 zd1211:interrupt in: wMaxPacketSize = 40 zd1211:interrupt in: int_interval = 1 zd1211:interrupt out: wMaxPacketSize = 40 EEPORM Ver = 4810 zd1211:USB Download Boot code success zd1211:MAC address = 00:60:b3:36:dd:27 zd1211:AddrEntryTable = f7c6 zd1211:RF_Mode = 00002109 PA type: 0 GCT RF zd1211:Mixed Mode zd1211:AllowedChannel = 000007ff zd1211:LinkLEDn = 200 AllowedChannel = 000107ff Region:48 zd1205: (exit) zd1205_config, /root/AR5007UG/zd1211-driver-r85/src/ zd1205.c line 2607 zd1205: (exit) zd1205_init, /root/AR5007UG/zd1211-driver-r85/src/zd1205.c li ne 8582 usbcore: registered new interface driver zd1211b zd1205: (enter) zd1205_open, /root/AR5007UG/zd1211-driver-r85/src/zd1205.c l ine 4359 zd1205: (exit) zd1205_open, /root/AR5007UG/zd1211-driver-r85/src/zd1205.c li ne 4442 ADDRCONF(NETDEV_UP): wlan0: link is not ready [/dmesg] [iwconfig] lo no wireless extensions. eth0 no wireless extensions. wlan0 802.11b/g NIC ESSID:"" Mode:Managed Frequency=2.462 GHz Access Point: Not-Associated Bit Rate:1 Mb/s Retry:off RTS thr=2432 B Fragment thr:off Encryption key:off Power Management:off Link Quality:0 Signal level:0 Noise level:0 Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 [/iwconfig] [/var/log/messages] May 15 22:47:06 (none) kernel: ZD1211B - http://zd1211.ath.cx/ - r85 May 15 22:47:06 (none) kernel: Based on www.zydas.com.tw driver version 2.5.0.0 May 15 22:47:06 (none) kernel: usb 2-1: reset high speed USB device using ehci_hcd and address 2 May 15 22:47:06 (none) kernel: Release Ver = 4810 May 15 22:47:06 (none) kernel: EEPORM Ver = 4810 May 15 22:47:07 (none) kernel: usbcore: registered new interface driver zd1211b May 15 22:47:29 (none) kernel: ADDRCONF(NETDEV_UP): wlan0: link is not ready [/messages] And now cat /proc/version as requested: Linux version 2.6.20-BT-PwnSauce-NOSMP ([EMAIL PROTECTED]) (gcc version 3.4.6) #3 Sat Feb 24 15:52:59 GMT 2007 Thanks for your help! Björn ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
