Hi Daniel, Sorry I mistyped ZD1211. Here is dmesg : > > [EMAIL PROTECTED] zd1211rw-strange-al2230s]$ make zd1211_DEBUG=y > > You mistyped, so no debug support was added.
[EMAIL PROTECTED] zd1211rw-strange-al2230s]$ make ZD1211_DEBUG=y ....(snip).... [EMAIL PROTECTED] zd1211rw-strange-al2230s]# rmmod zd1211rw [EMAIL PROTECTED] zd1211rw-strange-al2230s]# modprobe -v zd1211rw insmod /lib/modules/2.6.20-1.2316.fc5smp/kernel/drivers/net/wireless/zd1211rw/zd1211rw.ko ...(snip).... [EMAIL PROTECTED] zd1211rw]$ dmesg ...(snip).... usbcore: deregistering interface driver zd1211rw zd1211rw usb_init() usb 5-4: print_id() 0411:00da v4810 high usb 5-4: reset high speed USB device using ehci_hcd and address 4 zd1211rw 5-4:1.0: zd_netdev_alloc() netdev->flags 0x1002 zd1211rw 5-4:1.0: zd_netdev_alloc() netdev->features 0x00000000 usb 5-4: request_fw_file() fw name zd1211/zd1211b_ub usb 5-4: upload_firmware() firmware device id 0x4810 is equal to the actual device id usb 5-4: request_fw_file() fw name zd1211/zd1211b_uphr usb 5-4: upload_code() transfer size 4096 usb 5-4: upload_code() transfer size 1024 usb 5-4: upload_code() firmware confirm return value 0x01 zd1211rw 5-4:1.0: zd_usb_enable_int() zd1211rw 5-4:1.0: zd_usb_enable_int() submit urb d8931f40 zd1211rw 5-4:1.0: zd_chip_init_hw() zd1211rw 5-4:1.0: dump_cr() CR_AFTER_PNP 0x00000000 zd1211rw 5-4:1.0: dump_cr() CR_GPI_EN 0x00000000 zd1211rw 5-4:1.0: dump_cr() CR_INTERRUPT 0x00000000 zd1211rw 5-4:1.0: read_fw_regs_offset() fw_regs_base: 0xf7f1 zd1211rw 5-4:1.0: read_pod() E2P_POD 0xa000011a zd1211rw 5-4:1.0: read_pod() RF AL2230S_RF 0xa PA type 0x0 patch CCK 1 patch CR157 0 patch 6M 0 new PHY 1 link LED1 tx led 1 zd1211rw 5-4:1.0: hw_init() zd1211rw 5-4:1.0: zd1211b_hw_reset_phy() zd1211rw 5-4:1.0: zd_chip_lock_phy_regs() CR_REG1: 0x00 -> 0x00 zd1211rw 5-4:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x00 -> 0x80 zd1211rw 5-4:1.0: zd1211b_hw_init_hmac() zd1211rw 5-4:1.0: get_aw_pt_bi() aw 0 pt 0 bi 0 zd1211rw 5-4:1.0: set_aw_pt_bi() aw 0 pt 99 bi 100 zd1211rw 5-4:1.0: zd_chip_lock_phy_regs() CR_REG1: 0xa0 -> 0x20 zd1211rw 5-4:1.0: zd_usb_rfwrite() value 0x0241000 bits 24 zd1211rw 5-4:1.0: zd_chip_unlock_phy_regs() CR_REG1: 0x20 -> 0xa0 zd1211rw 5-4:1.0: firmware version 4725 zd1211rw 5-4:1.0: dump_fw_registers() FW_FIRMWARE_VER 0x4725 zd1211rw 5-4:1.0: dump_fw_registers() FW_USB_SPEED 0x0001 zd1211rw 5-4:1.0: dump_fw_registers() FW_FIX_TX_RATE 0x0000 zd1211rw 5-4:1.0: dump_fw_registers() FW_LINK_STATUS 0x0000 zd1211rw 5-4:1.0: dump_cr() CR_AFTER_PNP 0x00000001 zd1211rw 5-4:1.0: dump_cr() CR_GPI_EN 0x00000000 zd1211rw 5-4:1.0: dump_cr() CR_INTERRUPT 0x00000000 zd1211rw 5-4:1.0: zd1211b chip 0411:00da v4810 high 00-16-01 AL2230S_RF pa0 g--N- zd1211rw 5-4:1.0: zd_write_mac_addr() mac addr 00:16:01:6e:9a:80 zd1211rw 5-4:1.0: zd_read_regdomain() regdomain: 0x49 zd1211rw 5-4:1.0: zd_mac_init_hw() Regulatory Domain 0x49 is not supported. zd1211rw 5-4:1.0: zd_usb_disable_int() urb d8931f40 killed zd1211rw 5-4:1.0: probe() couldn't initialize mac. Error number -22 usb 5-4: reset high speed USB device using ehci_hcd and address 4 zd1211rw: probe of 5-4:1.0 failed with error -22 usbcore: registered new interface driver zd1211rw zd1211rw initialized [EMAIL PROTECTED] zd1211rw]$ Regards, Zen ------------------------------------------------------------------------- This SF.net email is sponsored by DB2 Express Download DB2 Express C - the FREE version of DB2 express and take control of your XML. No limits. Just data. Click to get it now. http://sourceforge.net/powerbar/db2/ _______________________________________________ Zd1211-devs mailing list - http://zd1211.ath.cx/ Unsubscribe: https://lists.sourceforge.net/lists/listinfo/zd1211-devs
