See below ..
On 7/22/2017 5:58 PM, Bjorn Pehrson wrote:
Neil,
Two newbie questions regarding your item 3 below, the two 2.5mm cables:
- My USB audio fob has 3.5mm female contacts, so I need 3.5 mm male
contacts in that end
- Where to hook up the other ends? In the KX3 I suppose, but both the
mic and the phone contacts are 3.5mm females, so why 2.5mm, or was
that just a typo? Do you mean 3.5mm?
That was a typo ... its 3.5 mm, sorry ... the Elecraft KX3-PCKT cable
set has these : a 3.5mm stereo right-angle to straight through cable
(green band), a 3.5mm stereo right-angle tostraight through cable (red
band). This is what I use.
Thanks for clarification
Bjorn, SA0BXI
On 2017-07-21 15:14, Neil Zampella wrote:
Tom,
Why are you using a Signalink ??? Its not needed for WSJT-X, and
I'm not sure that its needed for any other digital mode. You can
connect the KX to your computer using the steps below.
1. Find yourself a good USB external soundcard that provides a
48,000 Hz DVD quality INPUT and OUTPUT. WSJT-X requires this, you
can pick one up at Amazon for less than $30, or get a good one for
$70. I'm not sure the Signalink provides that DVD quality out.
2. Use the KUSB cable for CAT control. WSJT-X will use it for PTT
and Freq control.
3. Get two 2.5mm cables for the stereo in and out and hook them up
to the external soundcard.
4. Set the Windows audio in for the soundcard at 100, and use the
AF knob to set the dB in to WSJT-X
5. Use the rig's PWR knob to set the output power, and then when
in tx, set the MIC knob to show 4 bars of ALC
That's it ... in WSJT-X set the rig for K3/KX3, set the serial port
as the same one that the KUSB is assigned to, baud rate at 38400, 8
data bits, 2 stop bits, no handshake, PTT at CAT, Mode at Data/Pkt,
Split at RIG. Once its setup, the TEST CAT button there should turn
green, you can then click the TEST PTT and it will kick the rig in.
Hope this helps,
Neil, KN3ILZ
On 7/21/2017 8:08 AM, Tommy wrote:
Hi folks,
Trying to get WSJT-X going with FT8 and my new KX2. I keep
getting a "/Hamlib error/: IO /error/ while opening connection to
rig" error. I have the right cables and jumper module in the
signalink, Radio selection is KX3 (it's supposed to work), USB and
VOX is selected and VOX is ON. 8 bits, one stop and handshake NONE.
No matter what I do I still get the error.
Any ideas please? It's driving me nuts! This shouldn't be this
difficult. Any help appreciated.
Tom - KB2SMS
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to sa0...@ssa.se
.
-----
No virus found in this message.
Checked by AVG - www.avg.com
Version: 2016.0.8013 / Virus Database: 4779/14726 - Release Date:
07/22/17
______________________________________________________________
Elecraft mailing list
Home: http://mailman.qth.net/mailman/listinfo/elecraft
Help: http://mailman.qth.net/mmfaq.htm
Post: mailto:Elecraft@mailman.qth.net
This list hosted by: http://www.qsl.net
Please help support this email list: http://www.qsl.net/donate.html
Message delivered to arch...@mail-archive.com