Hi Gene Thanks so much. Would it be possible to get yojr mail adress so I can send you some more info on the drives and so forth please? beukes1...@gmail.com Thanks
On 28 Aug 2017 12:48, "Gene Heskett" <ghesk...@shentel.net> wrote: > On Monday 28 August 2017 03:49:17 Marius Liebenberg wrote: > > > Hi Johan > > > > You will have to provide a bit more detail in order to get assistance. > > Please explain what you mean by "does not hold size at all" > > Explain how: > > 1) you discovered the problem and > > 2) how you measured the result and > > 3) what you done to solve it thus far. > > > > Also give details on the controller version and GUI that you use. > > This might be that wobbly drunken duck created when the drivers are > wired - to ground, and + to the signal. Most circuits can pull down as > much as 10x what they can pull up, which lights the led in the drivers > input opto stuff up well. Reverseing that drive polarity is easy though. > > You tie the + terminal to the logic's + supply, and the - signal to the > breakout boards output. > > I've never heard of that driver, so some info on it could be usefull. > > > ------ Original Message ------ > > From: "Johann Beukes" <beukes1...@gmail.com> > > To: emc-users@lists.sourceforge.net > > Sent: 2017-08-28 06:12:00 > > Subject: [Emc-users] (no subject) > > > > >Hi guys > > >I am struggeling alot with my lathe X axis. The machine does not hold > > >size > > >at all. I am using The Leadshine ESM-22430 motor and the DS808 drive. > > >The > > >Dirsetup is set at 2500, Dirhold 2500, Steplen 5000, Stepspace 5000 > > > and stepscale at -322. The ballscrew has a 2.5mm pitch and the steps > > > per rev > > >are set at 800. > > >Can anybody please give me some advice? > > >Thanks > > >--------------------------------------------------------------------- > > >--------- Check out the vibrant tech community on one of the world's > > > most engaging tech sites, Slashdot.org! http://sdm.link/slashdot > > >_______________________________________________ > > >Emc-users mailing list > > >Emc-users@lists.sourceforge.net > > >https://lists.sourceforge.net/lists/listinfo/emc-users > > > > --- > > This email has been checked for viruses by Avast antivirus software. > > https://www.avast.com/antivirus > > ---------------------------------------------------------------------- > >-------- Check out the vibrant tech community on one of the world's > > most engaging tech sites, Slashdot.org! http://sdm.link/slashdot > > _______________________________________________ > > Emc-users mailing list > > Emc-users@lists.sourceforge.net > > https://lists.sourceforge.net/lists/listinfo/emc-users > > > Cheers, Gene Heskett > -- > "There are four boxes to be used in defense of liberty: > soap, ballot, jury, and ammo. Please use in that order." > -Ed Howdershelt (Author) > Genes Web page <http://geneslinuxbox.net:6309/gene> > > ------------------------------------------------------------ > ------------------ > Check out the vibrant tech community on one of the world's most > engaging tech sites, Slashdot.org! http://sdm.link/slashdot > _______________________________________________ > Emc-users mailing list > Emc-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/emc-users > ------------------------------------------------------------------------------ Check out the vibrant tech community on one of the world's most engaging tech sites, Slashdot.org! http://sdm.link/slashdot _______________________________________________ Emc-users mailing list Emc-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/emc-users
