On Wed, 13 Apr 2022, Marius wrote:
Date: Wed, 13 Apr 2022 19:29:50 +0200
From: Marius <mar...@mastercut.co.za>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)" <emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Looking for 7i92 bit file
On 2022/04/13 18:52, Peter C. Wallace wrote:
On Wed, 13 Apr 2022, Marius wrote:
Date: Wed, 13 Apr 2022 18:40:15 +0200
From: Marius <mar...@mastercut.co.za>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: Peter C. Wallace <p...@mesanet.com>
Subject: Re: [Emc-users] Looking for 7i92 bit file
I redid the config with 7i92_5ABOBx2D and the numbers on the side. I
got the allocation working. The only issue now is that the slave
stepgen does not give any output. It is assigned correctly but no
output on the pins. (3/4)
The Z axis is assigned to stepgen 4 on the other port (port 1)
instead of pin 16/17 on port 2
Thats why I suggested this firmware (you indicated that pins 16 17
were not stepgens)
Correct. It's not an issue. Just noted it. I looked at the source and it
does not assign a stepgen to the 16/17 pins of port 2. I might want to
change that for the next conversion where the Z axis will be used.
Did you setup the slave axis as X2?
It does but it deliberately sets it to stepgen 8 so it can be disabled
if use for spinel control on a 5ABOB breakout
I did set it up as X2. The INI and HAL also show that but I dont get
signal at the pin. I checked with the scope.
Probably a hal issue, I would check the hal file stepgen connections
On 2022/04/13 18:22, Marius wrote:
Does any of the numbers on the left side of the PnCConf dialog
correspond to the stepgen numbers?
Yes, the numbers to the left of the stepgen function selector are
the stepgen number
Thanks I will give it another go.
I cannot get this result at all. With 7i92_5ABOBx2D I do not get
8/9 assigned at all. It jumps to the next port and then it will
put stepgen 4 on the second port. You can see that from my
output that I posted on the forum. I redid the config in many
ways but I cannot force this allocation at all.
On 2022/04/12 16:35, Peter C. Wallace wrote:
On Tue, 12 Apr 2022, Marius wrote:
Date: Tue, 12 Apr 2022 16:22:37 +0200
From: Marius <mar...@mastercut.co.za>
Reply-To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
To: "Enhanced Machine Controller (EMC)"
<emc-users@lists.sourceforge.net>
Subject: Re: [Emc-users] Looking for 7i92 bit file
I attached a picture. Don't remember if that can be done.
This is the config I need but I will be damned if I can
get PnCConf to do this. Maybe I dont understand the GUI
where the pin allocations happen that well. If only they
would show the I/O number correctly somewhere. There are
some numbers on the left side but they make no sense.
The pinout is determined by the firmware so many
parallel port type 7I92 bitfiles will do
For example 7i92_5ABOBx2D.bit firmware will work here
You associate stepgen numbers to Axis in pncconf
The firmware maps those numbered stepgens to
physical pins
XSTEP - 2 : XDIR -3
X2STEP - 4 : X2DIR - 5
YSTEP - 6 : YDIR - 7
NO Z (or 16 and 17)
ASTEP - 8 : ADIR 9
On 2022/04/12 15:50, andy pugh wrote:
On Tue, 12 Apr 2022 at 13:48, Marius
<mar...@mastercut.co.za> wrote:
The config I have to replicate is this.
Seems to be coming through blank.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users
Peter Wallace
Mesa Electronics
(\__/)
(='.'=) This is Bunny. Copy and paste bunny into your
(")_(") signature to help him gain world domination.
_______________________________________________
Emc-users mailing list
Emc-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/emc-users