On Thu, 6 Apr 2023 15:56:57 -0400 mh via enlightenment-users <enlightenment-users@lists.sourceforge.net> said:
> > On 4/6/23 00:51, Carsten Haitzler wrote: > > On Wed, 5 Apr 2023 14:49:28 -0400 mh via enlightenment-users > > <enlightenment-users@lists.sourceforge.net> said: > > > >> On 4/5/23 12:43, Carsten Haitzler wrote: > >>> On Tue, 4 Apr 2023 20:22:32 -0400 mh via enlightenment-users > >>> <enlightenment-users@lists.sourceforge.net> said: > >>> > >>>> I'm just back to using E after a while, using 0.25.4 from Debian sid. > >>>> After first logging in, and every time after resuming from > >>>> screensaver/blanking, I get the pop-up error message: "You seem to have > >>>> no screens configured to be on the given outputs you have. This should > >>>> be fixed by going to: Settings-Screen-Screen Setup." > >>> is this a laptop? did you have the lid closed? > >> it's a desktop, 4080 gpu, evil NVIDIA driver version 530.30.02 installed > > this would imply the nvidia driver is unplugging all screens ever time the > > screen goes into dpms. check your logs as per previous email and see. all > > lines going RRR: will have to do with randr screen stuff. > > Not sure which log to check. I looked at Xorg.0.log but didn't see > anything with RRR. I was going to uninstall the nvidia drivers and try > it with nouveau but having problems with X starting. Not sure if nouveau > supports rtx4080 yet. ~/.e-log.log > >>>> When I do that, there is a list showing two DP-4 outputs where the > >>>> monitor is connected, and a third that lists the monitor. But the only > >>>> one that I can set the screen setup settings for is the first DP-4. What > >>>> do I need to do to setup the monitor to the output properly? > >>> what? multiple DP-4's - that shouldnt happen. you should have all outputs > >>> named differently. does xrandr (commandline) also list multiple dp-4's? > >> only one DP-4 with xrandr. this is the output: > >> > >> $ xrandr > >> Screen 0: minimum 8 x 8, current 3840 x 2160, maximum 32767 x 32767 > >> HDMI-0 disconnected primary (normal left inverted right x axis y axis) > >> DP-0 disconnected (normal left inverted right x axis y axis) > >> DP-1 disconnected (normal left inverted right x axis y axis) > >> DP-2 disconnected (normal left inverted right x axis y axis) > >> DP-3 disconnected (normal left inverted right x axis y axis) > >> DP-4 connected 3840x2160+0+0 (normal left inverted right x axis y axis) > >> 708mm x 399mm > >> 3840x2160 60.00*+ 144.00 120.00 119.88 59.94 50.00 29.97 > >> 2560x1440 143.97 120.00 59.95 > >> 1920x1080 143.85 119.88 60.00 59.94 > >> 1680x1050 59.95 > >> 1440x900 59.89 > >> 1280x1024 75.02 60.02 > >> 1280x960 60.00 > >> 1280x720 119.88 60.00 59.94 50.00 > >> 1152x864 75.00 > >> 1024x768 75.03 70.07 60.00 > >> 800x600 75.00 72.19 60.32 56.25 > >> 720x576 50.00 > >> 720x480 59.94 > >> 640x480 75.00 72.81 59.94 59.93 > >> DP-5 disconnected (normal left inverted right x axis y axis) > > are you sure dp-4 is listed twice and it isn't just the hoversel showing the > > selected one at the top in addition to the set of possible selections below? > I see DP-4 listed twice, then 32UHD144. If I hover/click over the first > DP-4 I see a DP-4, indented and selectable. But the second one remains > after I select a resolution and hit apply. The 32UHD144 entry is never > selectable. can you share screenshots? > >> _______________________________________________ > >> enlightenment-users mailing list > >> enlightenment-users@lists.sourceforge.net > >> https://lists.sourceforge.net/lists/listinfo/enlightenment-users > _______________________________________________ > enlightenment-users mailing list > enlightenment-users@lists.sourceforge.net > https://lists.sourceforge.net/lists/listinfo/enlightenment-users -- ------------- Codito, ergo sum - "I code, therefore I am" -------------- Carsten Haitzler - ras...@rasterman.com _______________________________________________ enlightenment-users mailing list enlightenment-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/enlightenment-users