On 4/7/23 04:45, Carsten Haitzler wrote:
On Thu, 6 Apr 2023 19:16:01 -0400 mh<mhe...@icloud.com> said:
On 4/6/23 18:09, Carsten Haitzler wrote:
On Thu, 6 Apr 2023 15:56:57 -0400 mh via enlightenment-users
<enlightenment-users@lists.sourceforge.net> said:
On 4/6/23 00:51, Carsten Haitzler wrote:
On Wed, 5 Apr 2023 14:49:28 -0400 mh via enlightenment-users
<enlightenment-users@lists.sourceforge.net> said:
On 4/5/23 12:43, Carsten Haitzler wrote:
On Tue, 4 Apr 2023 20:22:32 -0400 mh via enlightenment-users
<enlightenment-users@lists.sourceforge.net> said:
I'm just back to using E after a while, using 0.25.4 from Debian sid.
After first logging in, and every time after resuming from
screensaver/blanking, I get the pop-up error message: "You seem to have
no screens configured to be on the given outputs you have. This should
be fixed by going to: Settings-Screen-Screen Setup."
is this a laptop? did you have the lid closed?
it's a desktop, 4080 gpu, evil NVIDIA driver version 530.30.02 installed
this would imply the nvidia driver is unplugging all screens ever time the
screen goes into dpms. check your logs as per previous email and see. all
lines going RRR: will have to do with randr screen stuff.
Not sure which log to check. I looked at Xorg.0.log but didn't see
anything with RRR. I was going to uninstall the nvidia drivers and try
it with nouveau but having problems with X starting. Not sure if nouveau
supports rtx4080 yet.
~/.e-log.log
yes, a LOT of RRR messages... Seem to be several sections where the
screens are "reconfigure screens due to event..." That must nvidia
unplugging the screens.
So if I use nouveau should that stop that?
within all those RRR messages it'll list outputs if they are connected or not
etc. when queried... read them carefully (yes - i know. lots of them) and it
shows the decision logic coming from E and why it's doing that.
I will do that, and see about getting nouveau running again to see if
that stops the error.
When I do that, there is a list showing two DP-4 outputs where the
monitor is connected, and a third that lists the monitor. But the only
one that I can set the screen setup settings for is the first DP-4.
What do I need to do to setup the monitor to the output properly?
what? multiple DP-4's - that shouldnt happen. you should have all
outputs named differently. does xrandr (commandline) also list multiple
dp-4's?
only one DP-4 with xrandr. this is the output:
$ xrandr
Screen 0: minimum 8 x 8, current 3840 x 2160, maximum 32767 x 32767
HDMI-0 disconnected primary (normal left inverted right x axis y axis)
DP-0 disconnected (normal left inverted right x axis y axis)
DP-1 disconnected (normal left inverted right x axis y axis)
DP-2 disconnected (normal left inverted right x axis y axis)
DP-3 disconnected (normal left inverted right x axis y axis)
DP-4 connected 3840x2160+0+0 (normal left inverted right x axis y axis)
708mm x 399mm
3840x2160 60.00*+ 144.00 120.00 119.88 59.94 50.00
29.97 2560x1440 143.97 120.00 59.95
1920x1080 143.85 119.88 60.00 59.94
1680x1050 59.95
1440x900 59.89
1280x1024 75.02 60.02
1280x960 60.00
1280x720 119.88 60.00 59.94 50.00
1152x864 75.00
1024x768 75.03 70.07 60.00
800x600 75.00 72.19 60.32 56.25
720x576 50.00
720x480 59.94
640x480 75.00 72.81 59.94 59.93
DP-5 disconnected (normal left inverted right x axis y axis)
are you sure dp-4 is listed twice and it isn't just the hoversel showing
the selected one at the top in addition to the set of possible selections
below?
I see DP-4 listed twice, then 32UHD144. If I hover/click over the first
DP-4 I see a DP-4, indented and selectable. But the second one remains
after I select a resolution and hit apply. The 32UHD144 entry is never
selectable.
can you share screenshots?
I have two. I'll attach them here, but if that doesn't work I can find
some place to post them. The e-screen-setup1 is first going to Screen
Setup, e-screen-setup2 is after clicking on the top DP-4.
oooooh... you don't have it listed twice. that below the hoversel above where
you select is just the name of the output selected - it's not part of the list
or selector - it's a separate entry widget you can copy & paste from (even type
into - tho it wont be useful to do that). so no bug here. it shows only 1
output. DP-4 (when you click on the hoversel above to select the output it
lists only 1 in addition to what is selected).
Got it, thanks for helping me to understand what I'm seeing!
_______________________________________________
enlightenment-users mailing list
enlightenment-users@lists.sourceforge.net
https://lists.sourceforge.net/lists/listinfo/enlightenment-users
