On Thu, 6 Apr 2023 19:16:01 -0400 mh <mhe...@icloud.com> said: > > On 4/6/23 18:09, Carsten Haitzler wrote: > > On Thu, 6 Apr 2023 15:56:57 -0400 mh via enlightenment-users > > <enlightenment-users@lists.sourceforge.net> said: > > > >> On 4/6/23 00:51, Carsten Haitzler wrote: > >>> On Wed, 5 Apr 2023 14:49:28 -0400 mh via enlightenment-users > >>> <enlightenment-users@lists.sourceforge.net> said: > >>> > >>>> On 4/5/23 12:43, Carsten Haitzler wrote: > >>>>> On Tue, 4 Apr 2023 20:22:32 -0400 mh via enlightenment-users > >>>>> <enlightenment-users@lists.sourceforge.net> said: > >>>>> > >>>>>> I'm just back to using E after a while, using 0.25.4 from Debian sid. > >>>>>> After first logging in, and every time after resuming from > >>>>>> screensaver/blanking, I get the pop-up error message: "You seem to have > >>>>>> no screens configured to be on the given outputs you have. This should > >>>>>> be fixed by going to: Settings-Screen-Screen Setup." > >>>>> is this a laptop? did you have the lid closed? > >>>> it's a desktop, 4080 gpu, evil NVIDIA driver version 530.30.02 installed > >>> this would imply the nvidia driver is unplugging all screens ever time the > >>> screen goes into dpms. check your logs as per previous email and see. all > >>> lines going RRR: will have to do with randr screen stuff. > >> Not sure which log to check. I looked at Xorg.0.log but didn't see > >> anything with RRR. I was going to uninstall the nvidia drivers and try > >> it with nouveau but having problems with X starting. Not sure if nouveau > >> supports rtx4080 yet. > > ~/.e-log.log > > yes, a LOT of RRR messages... Seem to be several sections where the > screens are "reconfigure screens due to event..." That must nvidia > unplugging the screens. > > So if I use nouveau should that stop that?
within all those RRR messages it'll list outputs if they are connected or not etc. when queried... read them carefully (yes - i know. lots of them) and it shows the decision logic coming from E and why it's doing that. > >>>>>> When I do that, there is a list showing two DP-4 outputs where the > >>>>>> monitor is connected, and a third that lists the monitor. But the only > >>>>>> one that I can set the screen setup settings for is the first DP-4. > >>>>>> What do I need to do to setup the monitor to the output properly? > >>>>> what? multiple DP-4's - that shouldnt happen. you should have all > >>>>> outputs named differently. does xrandr (commandline) also list multiple > >>>>> dp-4's? > >>>> only one DP-4 with xrandr. this is the output: > >>>> > >>>> $ xrandr > >>>> Screen 0: minimum 8 x 8, current 3840 x 2160, maximum 32767 x 32767 > >>>> HDMI-0 disconnected primary (normal left inverted right x axis y axis) > >>>> DP-0 disconnected (normal left inverted right x axis y axis) > >>>> DP-1 disconnected (normal left inverted right x axis y axis) > >>>> DP-2 disconnected (normal left inverted right x axis y axis) > >>>> DP-3 disconnected (normal left inverted right x axis y axis) > >>>> DP-4 connected 3840x2160+0+0 (normal left inverted right x axis y axis) > >>>> 708mm x 399mm > >>>> 3840x2160 60.00*+ 144.00 120.00 119.88 59.94 50.00 > >>>> 29.97 2560x1440 143.97 120.00 59.95 > >>>> 1920x1080 143.85 119.88 60.00 59.94 > >>>> 1680x1050 59.95 > >>>> 1440x900 59.89 > >>>> 1280x1024 75.02 60.02 > >>>> 1280x960 60.00 > >>>> 1280x720 119.88 60.00 59.94 50.00 > >>>> 1152x864 75.00 > >>>> 1024x768 75.03 70.07 60.00 > >>>> 800x600 75.00 72.19 60.32 56.25 > >>>> 720x576 50.00 > >>>> 720x480 59.94 > >>>> 640x480 75.00 72.81 59.94 59.93 > >>>> DP-5 disconnected (normal left inverted right x axis y axis) > >>> are you sure dp-4 is listed twice and it isn't just the hoversel showing > >>> the selected one at the top in addition to the set of possible selections > >>> below? > >> I see DP-4 listed twice, then 32UHD144. If I hover/click over the first > >> DP-4 I see a DP-4, indented and selectable. But the second one remains > >> after I select a resolution and hit apply. The 32UHD144 entry is never > >> selectable. > > can you share screenshots? > > I have two. I'll attach them here, but if that doesn't work I can find > some place to post them. The e-screen-setup1 is first going to Screen > Setup, e-screen-setup2 is after clicking on the top DP-4. oooooh... you don't have it listed twice. that below the hoversel above where you select is just the name of the output selected - it's not part of the list or selector - it's a separate entry widget you can copy & paste from (even type into - tho it wont be useful to do that). so no bug here. it shows only 1 output. DP-4 (when you click on the hoversel above to select the output it lists only 1 in addition to what is selected). -- ------------- Codito, ergo sum - "I code, therefore I am" -------------- Carsten Haitzler - ras...@rasterman.com _______________________________________________ enlightenment-users mailing list enlightenment-users@lists.sourceforge.net https://lists.sourceforge.net/lists/listinfo/enlightenment-users