Hi Greg,
(I've installed 2.4.22-pre3 now)
Yes, I do have ACPI enabled. That's the reason I went with the 2.4.22-preX
series, since ACPI is already incorporated (less patches). I'm not keen on
2.5.x right now....
I found out (after lots of hangs and restarts) that the problem has to do
with the IRQ setting of the USB ports. I had the built-in Ethernet port
set to Auto in the BIOS (enabled only when on AC power or Ethernet cable
plugged in). When powering up in battery-only mode (eth0 disabled), the
USB IRQ was set to 10, while it is set to 9 in AC power mode (sharing with
eth0/8139too driver).
The dmesg logs of both cases are attached.
If the IRQ is 10, it will hang the machine hard (regardless of cold-boot,
warm-boot or after WinXP).
Do the developers read this list, or else who can escalate this (I'm not
subscribed to the usb-devel list)?
Slightly offtopic, how much power does eth0 drain? I didn't set it to
"Always Enabled" previously but if it doesn't drain too much power I might
just enable it all the time to avoid the hangs.
T.C.
On Mon, 7 Jul 2003, Greg KH wrote:
> On Mon, Jul 07, 2003 at 01:48:42PM -0700, Greg KH wrote:
> > I'm typing this from 2.4.21 + acpi patch right now, haven't booted
> > 2.4.22-preX at all on this box.
>
> Just tried 2.4.22-pre3, works just fine. Nice thing is you don't have
> to add the acpi patch anymore :)
>
> Oh, remember, you _have_ to enable acpi to get this box to work. Do you
> have that enabled?
>
> greg k-h
>
Linux version 2.4.22-pre3 ([EMAIL PROTECTED]) (gcc version 3.2.2 20030222 (Red Hat
Linux 3.2.2-5)) #1 Mon Jul 7 18:21:21 MYT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000efe0000 (usable)
BIOS-e820: 000000000efe0000 - 000000000efefc00 (ACPI data)
BIOS-e820: 000000000efefc00 - 000000000eff0000 (ACPI NVS)
BIOS-e820: 000000000eff0000 - 000000000f100000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
239MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 61408
zone(0): 4096 pages.
zone(1): 57312 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 FUJ ) @ 0x000f6f70
ACPI: RSDT (v001 FUJ PAULING3 00261.00000) @ 0x0efec50d
ACPI: FADT (v001 FUJ PAULING3 00261.00000) @ 0x0efefa6a
ACPI: SSDT (v001 PTLTD ACPIPST1 00000.00001) @ 0x0efefade
ACPI: BOOT (v001 FUJ PAULING3 00261.00000) @ 0x0efefbd8
ACPI: DSDT (v001 FUJ PAULING3 00261.00000) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: ro root=LABEL=/ hdc=ide-scsi vga=0x317 video=vesa:ypan
resume=/dev/hda8
ide_setup: hdc=ide-scsi
No local APIC present or hardware disabled
Initializing CPU#0
Detected 925.430 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1841.56 BogoMIPS
Memory: 239768k/245632k available (1726k kernel code, 5464k reserved, 616k data, 132k
init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 512K (128 bytes/line)
CPU: Processor revision 1.4.1.0, 933 MHz
CPU: Code Morphing Software revision 4.3.2-9-566
CPU: 20030108 13:03 official release 28.0.3-4.3.2#1
CPU: After generic, caps: 0080893f 0081813f 0000004e 00000000
CPU: Common caps: 0080893f 0081813f 0000004e 00000000
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: none
ACPI: Subsystem revision 20030619
PCI: PCI BIOS revision 2.10 entry at 0xfd89e, last bus=1
PCI: Using configuration type 1
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control
Methods:........................................................................................................................................................
Table [DSDT](id F005) - 540 Objects with 46 Devices 152 Methods 24 Regions
Parsing all Control Methods:
Table [SSDT](id F003) - 3 Objects with 0 Devices 0 Methods 0 Regions
ACPI Namespace successfully loaded at root c037dcdc
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 63 [_GPE] 8 regs at
000000000000FF18 on int 9
Completing Region/Field/Buffer/Package
initialization:...........................................................................
Initialized 24/24 Regions 0/0 Fields 23/23 Buffers 28/28 Packages (551 nodes)
Executing all Device _STA and_INI
methods:...............................................
47 Devices found containing: 47 _STA, 7 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 (swsusp) S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 0)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7 9 10 *11)
ACPI: Power Resource [USBP] (on)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 11
pci_irq-0297 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0
PCI: No IRQ known for interrupt pin A of device 00:0f.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [CMB1] (battery present)
ACPI: Battery Slot [CMB2] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
acpi_processor-0899 [28] acpi_processor_get_per: Unsupported address space [127]
(control_register)
ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states)
vesafb: framebuffer at 0xf0000000, mapped to 0xcf80b000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:51d3
vesafb: pmi: set display start = c00c5267, set palette = c00c52b3
vesafb: pmi: ports = 1410 1416 1454 1438 143c 145c 1400 1404 14b0 14b2 14b4
vesafb: scrolling: ypan using protected mode interface, yres_virtual=1536
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP
enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 189M
agpgart: no supported devices found.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0f.0
pci_irq-0297 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0
PCI: No IRQ known for interrupt pin A of device 00:0f.0
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK3021GAS, ATA DISK drive
blk: queue c0395320, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA DVD-ROM SD-R2212, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58605120 sectors (30006 MB), CHS=3648/255/63, UDMA(66)
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel PCIC probe: not found.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Yenta IRQ list 0cf8, PCI irq9
Socket status: 30000006
Resume Machine: This is normal swap space
Swsusp 1.0_pre16-2_4_21: kswsuspd starting
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 82k freed
VFS: Mounted root (ext2 filesystem).
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
(recovery.c, 256): journal_recover: JBD: recovery, exit status 0, recovered
transactions 45510 to 45523
(recovery.c, 258): journal_recover: JBD: Replayed 476 and revoked 0/1 blocks
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xcfb2c000, IRQ 11
usb-ohci.c: usb-00:02.0, ALi Corporation USB 1.1 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Enabling device 00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 00:09.0 to 64
usb-ohci.c: USB OHCI at membase 0xcfb2e000, IRQ 9
usb-ohci.c: usb-00:09.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 1 port detected
PCI: Enabling device 00:09.1 (0000 -> 0002)
PCI: Setting latency timer of device 00:09.1 to 64
usb-ohci.c: USB OHCI at membase 0xcfb30000, IRQ 9
usb-ohci.c: usb-00:09.1, NEC Corporation USB (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 1 port detected
PCI: Enabling device 00:09.2 (0000 -> 0002)
ehci_hcd 00:09.2: NEC Corporation USB 2.0
ehci_hcd 00:09.2: irq 9, pci mem cfb38000
usb.c: new USB bus registered, assigned bus number 4
PCI: 00:09.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:09.2 PCI cache line size corrected to 32.
ehci_hcd 00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal
Adding Swap: 1052216k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 952 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[9] MMIO=[e8016000-e80167ff] Max Packet=[2048]
ieee1394: Host added: Node[00:1023] GUID[00000e1000f0496e] [Linux OHCI-1394]
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-R2212 Rev: 1F17
Type: CD-ROM ANSI SCSI revision: 02
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
ip_tables: (C) 2000-2002 Netfilter core team
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
8139too Fast Ethernet driver 0.9.26
eth0: RealTek RTL8139 Fast Ethernet at 0xcfc73800, 00:e0:00:fa:91:46, IRQ 9
eth0: Identified 8139 chip type 'RTL-8139C'
eth0: Setting half-duplex based on auto-negotiated partner ability 0000.
i2c-core.o: i2c core module version 2.7.0 (20021208)
i2c-ali1535.o version 2.7.0 (20021208)
i2c-ali1535.o: ALI1535 SMBus Controller detected and initialized
fjkeyinf: Application Panel Driver v0.4
fjkeyinf: Copyright (c) 2001 by Jochen Eisinger <[EMAIL PROTECTED]>
SysRq : Emergency Sync
Syncing device 03:09 ... OK
Syncing device 03:02 ... OK
Syncing device 03:06 ... OK
Syncing device 03:01 ... OK
Syncing device 03:0a ... OK
Syncing device 03:07 ... OK
Syncing device 03:05 ... OK
Done.
hub.c: new USB device 00:09.1-1, assigned address 2
usb.c: USB device 2 (vend/prod 0xd7d/0x100) is not claimed by any active driver.
Initializing USB Mass Storage driver...
usb.c: registered new driver usb-storage
scsi1 : SCSI emulation for USB Mass Storage devices
Vendor: Model: USB DISK Rev: 2.08
Type: Direct-Access ANSI SCSI revision: 02
WARNING: USB Mass Storage data integrity not assured
USB Mass Storage device found at 2
USB Mass Storage support registered.
Linux version 2.4.22-pre3 ([EMAIL PROTECTED]) (gcc version 3.2.2 20030222 (Red Hat
Linux 3.2.2-5)) #1 Mon Jul 7 18:21:21 MYT 2003
BIOS-provided physical RAM map:
BIOS-e820: 0000000000000000 - 000000000009c000 (usable)
BIOS-e820: 000000000009c000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e8000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 000000000efe0000 (usable)
BIOS-e820: 000000000efe0000 - 000000000efefc00 (ACPI data)
BIOS-e820: 000000000efefc00 - 000000000eff0000 (ACPI NVS)
BIOS-e820: 000000000eff0000 - 000000000f100000 (reserved)
BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved)
239MB LOWMEM available.
ACPI: have wakeup address 0xc0001000
On node 0 totalpages: 61408
zone(0): 4096 pages.
zone(1): 57312 pages.
zone(2): 0 pages.
ACPI: RSDP (v000 FUJ ) @ 0x000f6f70
ACPI: RSDT (v001 FUJ PAULING3 00261.00000) @ 0x0efec50d
ACPI: FADT (v001 FUJ PAULING3 00261.00000) @ 0x0efefa6a
ACPI: SSDT (v001 PTLTD ACPIPST1 00000.00001) @ 0x0efefade
ACPI: BOOT (v001 FUJ PAULING3 00261.00000) @ 0x0efefbd8
ACPI: DSDT (v001 FUJ PAULING3 00261.00000) @ 0x00000000
ACPI: BIOS passes blacklist
ACPI: MADT not present
Kernel command line: ro root=LABEL=/ hdc=ide-scsi vga=0x317 video=vesa:ypan
resume=/dev/hda8
ide_setup: hdc=ide-scsi
No local APIC present or hardware disabled
Initializing CPU#0
Detected 925.403 MHz processor.
Console: colour dummy device 80x25
Calibrating delay loop... 1841.56 BogoMIPS
Memory: 239768k/245632k available (1726k kernel code, 5464k reserved, 616k data, 132k
init, 0k highmem)
Dentry cache hash table entries: 32768 (order: 6, 262144 bytes)
Inode cache hash table entries: 16384 (order: 5, 131072 bytes)
Mount cache hash table entries: 512 (order: 0, 4096 bytes)
Buffer-cache hash table entries: 16384 (order: 4, 65536 bytes)
Page-cache hash table entries: 65536 (order: 6, 262144 bytes)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (32 bytes/line)
CPU: L2 Cache: 512K (128 bytes/line)
CPU: Processor revision 1.4.1.0, 933 MHz
CPU: Code Morphing Software revision 4.3.2-9-566
CPU: 20030108 13:03 official release 28.0.3-4.3.2#1
CPU: After generic, caps: 0080893f 0081813f 0000004e 00000000
CPU: Common caps: 0080893f 0081813f 0000004e 00000000
CPU: Transmeta(tm) Crusoe(tm) Processor TM5800 stepping 03
Checking 'hlt' instruction... OK.
POSIX conformance testing by UNIFIX
mtrr: v1.40 (20010327) Richard Gooch ([EMAIL PROTECTED])
mtrr: detected mtrr type: none
ACPI: Subsystem revision 20030619
PCI: PCI BIOS revision 2.10 entry at 0xfd89e, last bus=1
PCI: Using configuration type 1
tbxface-0117 [03] acpi_load_tables : ACPI Tables successfully acquired
Parsing all Control
Methods:........................................................................................................................................................
Table [DSDT](id F005) - 540 Objects with 46 Devices 152 Methods 24 Regions
Parsing all Control Methods:
Table [SSDT](id F003) - 3 Objects with 0 Devices 0 Methods 0 Regions
ACPI Namespace successfully loaded at root c037dcdc
evxfevnt-0093 [04] acpi_enable : Transition to ACPI mode successful
evgpeblk-0748 [06] ev_create_gpe_block : GPE 00 to 63 [_GPE] 8 regs at
000000000000FF18 on int 9
Completing Region/Field/Buffer/Package
initialization:...........................................................................
Initialized 24/24 Regions 0/0 Fields 23/23 Buffers 28/28 Packages (551 nodes)
Executing all Device _STA and_INI
methods:...............................................
47 Devices found containing: 47 _STA, 7 _INI methods
ACPI: Interpreter enabled
ACPI: Using PIC for interrupt routing
ACPI: System [ACPI] (supports S0 S3 (swsusp) S4 S5)
ACPI: PCI Root Bridge [PCI0] (00:00)
PCI: Probing PCI hardware (bus 00)
ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
ACPI: Embedded Controller [EC] (gpe 0)
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 9 10 11, disabled)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 *9 10 11)
ACPI: PCI Interrupt Link [LNKU] (IRQs 3 4 5 7 9 10 *11)
ACPI: Power Resource [USBP] (on)
PCI: Probing PCI hardware
ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 10
ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5
ACPI: PCI Interrupt Link [LNKF] enabled at IRQ 11
ACPI: PCI Interrupt Link [LNKG] enabled at IRQ 10
pci_irq-0297 [23] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0
PCI: No IRQ known for interrupt pin A of device 00:0f.0
PCI: Using ACPI for IRQ routing
PCI: if you experience problems, try using option 'pci=noacpi' or even 'acpi=off'
isapnp: Scanning for PnP cards...
isapnp: No Plug & Play device found
Linux NET4.0 for Linux 2.4
Based upon Swansea University Computer Society NET3.039
Initializing RT netlink socket
Starting kswapd
Journalled Block Device driver loaded
ACPI: AC Adapter [AC] (off-line)
ACPI: Battery Slot [CMB1] (battery present)
ACPI: Battery Slot [CMB2] (battery absent)
ACPI: Power Button (FF) [PWRF]
ACPI: Lid Switch [LID]
acpi_processor-0899 [28] acpi_processor_get_per: Unsupported address space [127]
(control_register)
ACPI: Processor [CPU0] (supports C1 C2 C3, 8 throttling states)
vesafb: framebuffer at 0xf0000000, mapped to 0xcf80b000, size 3072k
vesafb: mode is 1024x768x16, linelength=2048, pages=4
vesafb: protected mode interface info at c000:51d3
vesafb: pmi: set display start = c00c5267, set palette = c00c52b3
vesafb: pmi: ports = 1410 1416 1454 1438 143c 145c 1400 1404 14b0 14b2 14b4
vesafb: scrolling: ypan using protected mode interface, yres_virtual=1536
vesafb: directcolor: size=0:5:6:5, shift=0:11:5:0
Console: switching to colour frame buffer device 128x48
fb0: VESA VGA frame buffer device
pty: 256 Unix98 ptys configured
Serial driver version 5.05c (2001-07-08) with MANY_PORTS SHARE_IRQ SERIAL_PCI ISAPNP
enabled
floppy0: no floppy controllers found
RAMDISK driver initialized: 16 RAM disks of 4096K size 1024 blocksize
Linux agpgart interface v0.99 (c) Jeff Hartmann
agpgart: Maximum main memory to use for agp memory: 189M
agpgart: no supported devices found.
Uniform Multi-Platform E-IDE driver Revision: 7.00beta4-2.4
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
ALI15X3: IDE controller at PCI slot 00:0f.0
pci_irq-0297 [22] acpi_pci_irq_derive : Unable to derive IRQ for device 00:0f.0
PCI: No IRQ known for interrupt pin A of device 00:0f.0
ALI15X3: chipset revision 195
ALI15X3: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0x1800-0x1807, BIOS settings: hda:DMA, hdb:pio
ide1: BM-DMA at 0x1808-0x180f, BIOS settings: hdc:DMA, hdd:pio
hda: TOSHIBA MK3021GAS, ATA DISK drive
blk: queue c0395320, I/O limit 4095Mb (mask 0xffffffff)
hdc: TOSHIBA DVD-ROM SD-R2212, ATAPI CD/DVD-ROM drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide1 at 0x170-0x177,0x376 on irq 15
hda: attached ide-disk driver.
hda: host protected area => 1
hda: 58605120 sectors (30006 MB), CHS=3648/255/63, UDMA(66)
Partition check:
hda: hda1 hda2 hda3 hda4 < hda5 hda6 hda7 hda8 hda9 hda10 >
Linux Kernel Card Services 3.1.22
options: [pci] [cardbus] [pm]
Intel PCIC probe: not found.
NET4: Linux TCP/IP 1.0 for NET4.0
IP Protocols: ICMP, UDP, TCP, IGMP
IP: routing cache hash table of 2048 buckets, 16Kbytes
TCP: Hash tables configured (established 16384 bind 32768)
Linux IP multicast router 0.06 plus PIM-SM
NET4: Unix domain sockets 1.0/SMP for Linux NET4.0.
Yenta IRQ list 0cf8, PCI irq9
Socket status: 30000006
Resume Machine: This is normal swap space
Swsusp 1.0_pre16-2_4_21: kswsuspd starting
RAMDISK: Compressed image found at block 0
Freeing initrd memory: 82k freed
VFS: Mounted root (ext2 filesystem).
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
(recovery.c, 256): journal_recover: JBD: recovery, exit status 0, recovered
transactions 45499 to 45509
(recovery.c, 258): journal_recover: JBD: Replayed 435 and revoked 0/1 blocks
kjournald starting. Commit interval 5 seconds
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Freeing unused kernel memory: 132k freed
usb.c: registered new driver usbdevfs
usb.c: registered new driver hub
usb-ohci.c: USB OHCI at membase 0xcfb2c000, IRQ 11
usb-ohci.c: usb-00:02.0, ALi Corporation USB 1.1 Controller
usb.c: new USB bus registered, assigned bus number 1
hub.c: USB hub found
hub.c: 3 ports detected
PCI: Enabling device 00:09.0 (0000 -> 0002)
PCI: Setting latency timer of device 00:09.0 to 64
usb-ohci.c: USB OHCI at membase 0xcfb2e000, IRQ 9
usb-ohci.c: usb-00:09.0, NEC Corporation USB
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 1 port detected
PCI: Enabling device 00:09.1 (0000 -> 0002)
PCI: Setting latency timer of device 00:09.1 to 64
usb-ohci.c: USB OHCI at membase 0xcfb30000, IRQ 10
usb-ohci.c: usb-00:09.1, NEC Corporation USB (#2)
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 1 port detected
PCI: Enabling device 00:09.2 (0000 -> 0002)
ehci_hcd 00:09.2: NEC Corporation USB 2.0
ehci_hcd 00:09.2: irq 9, pci mem cfb38000
usb.c: new USB bus registered, assigned bus number 4
PCI: 00:09.2 PCI cache line size set incorrectly (0 bytes) by BIOS/FW.
PCI: 00:09.2 PCI cache line size corrected to 32.
ehci_hcd 00:09.2: USB 2.0 enabled, EHCI 0.95, driver 2003-Jun-19/2.4
hub.c: USB hub found
hub.c: 2 ports detected
usb.c: registered new driver hiddev
usb.c: registered new driver hid
hid-core.c: v1.8.1 Andreas Gal, Vojtech Pavlik <[EMAIL PROTECTED]>
hid-core.c: USB HID support drivers
mice: PS/2 mouse device common for all mice
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,9), internal journal
Adding Swap: 1052216k swap-space (priority -1)
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,2), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,6), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,7), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
kjournald starting. Commit interval 5 seconds
EXT3 FS 2.4-0.9.19, 19 August 2002 on ide0(3,5), internal journal
EXT3-fs: mounted filesystem with ordered data mode.
ohci1394: $Rev: 952 $ Ben Collins <[EMAIL PROTECTED]>
ohci1394_0: OHCI-1394 1.1 (PCI): IRQ=[9] MMIO=[e8016000-e80167ff] Max Packet=[2048]
ieee1394: Host added: Node[00:1023] GUID[00000e1000f0496e] [Linux OHCI-1394]
SCSI subsystem driver Revision: 1.00
hdc: attached ide-scsi driver.
scsi0 : SCSI host adapter emulation for IDE ATAPI devices
Vendor: TOSHIBA Model: DVD-ROM SD-R2212 Rev: 1F17
Type: CD-ROM ANSI SCSI revision: 02
cs: IO port probe 0x0c00-0x0cff: clean.
cs: IO port probe 0x0100-0x04ff: excluding 0x408-0x40f 0x480-0x48f 0x4d0-0x4d7
cs: IO port probe 0x0a00-0x0aff: clean.
Attached scsi CD-ROM sr0 at scsi0, channel 0, id 0, lun 0
sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
Uniform CD-ROM driver Revision: 3.12
ip_tables: (C) 2000-2002 Netfilter core team
IPv6 v0.8 for NET4.0
IPv6 over IPv4 tunneling driver
8139too Fast Ethernet driver 0.9.26
i2c-core.o: i2c core module version 2.7.0 (20021208)
i2c-ali1535.o version 2.7.0 (20021208)
i2c-ali1535.o: ALI1535 SMBus Controller detected and initialized
fjkeyinf: Application Panel Driver v0.4
fjkeyinf: Copyright (c) 2001 by Jochen Eisinger <[EMAIL PROTECTED]>
i2c-ali1535.o: Error: command never completed
SysRq : Emergency Sync
Syncing device 03:09 ... OK
Syncing device 03:02 ... OK
Syncing device 03:06 ... OK
Syncing device 03:01 ... OK
Syncing device 03:0a ... OK
Syncing device 03:07 ... OK
Syncing device 03:05 ... OK
Done.
