[gentoo-user] Need help networking two machines.
Hi I have done this before. Maybe something has changed because I can not get it to work now. My main rig is called smoker. The second rig is currently booted off the CD. I plan to use my main rig to sync and get distfiles off of. This is off smokers /etc/conf.d/net file: config_eth0=( 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 ) More info from smoker: eth0 Link encap:Ethernet HWaddr 00:01:53:81:00:E7 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:205 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16458 (16.0 Kb) TX bytes:5670 (5.5 Kb) Interrupt:10 Base address:0xc000 [EMAIL PROTECTED] / # ping 192.168.0.2 PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data. From 192.168.0.1 icmp_seq=1 Destination Host Unreachable From 192.168.0.1 icmp_seq=2 Destination Host Unreachable From 192.168.0.1 icmp_seq=3 Destination Host Unreachable --- 192.168.0.2 ping statistics --- 5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 4009ms , pipe 3 [EMAIL PROTECTED] / # If it helps any, I see traffic going over the network in gkrellm. [EMAIL PROTECTED] / # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface nas2.greenwood1 * 255.255.255.255 UH0 0 0 ppp0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 loopback* 255.0.0.0 U 0 00 lo default nas2.greenwood1 0.0.0.0 UG0 0 0 ppp0 [EMAIL PROTECTED] / # Yea, ppp0 would be that slow as crap dial-up connection I have. cries [EMAIL PROTECTED] / # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- anywhere anywheretcp dpt:http DROP all -- anywhere anywherestate INVALID,NEW Chain FORWARD (policy ACCEPT) target prot opt source destination DROP all -- anywhere anywherestate INVALID,NEW Chain OUTPUT (policy ACCEPT) target prot opt source destination [EMAIL PROTECTED] / # Now the info from the second rig is a bit hard to get. I can't exactly copy and paste here. Help me get this working and I'll copy and paste all you want. LOL Second rig is the same setup except it is set to address 192.168.0.2. I did restart the network though, on both rigs. Route returns loopback and that is all. Looks suspicious to me. It doesn't have iptables installed on the CD. I guess there are none. Oh, to test the cable, I set both to the same address. When I tried to bring up the network, it gave me a error that the address was in use or something like that. It saw it at least. Can someone tell me what I am doing wrong? It has to be me. It almost always is. Thanks for the help. Dale :-) :-) :-) -- www.myspace.com/dalek1967 -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] usb scanner HP2200c
On Fri, 12 Jan 2007 01:28:47 +0100, Mihamina Rakotomandimby (R12y) wrote: When I launch xsane, it says it does not detect any device. I launch it as user, I already added me to the scanner group. [EMAIL PROTECTED] ~ $ sane-find-scanner -q found USB scanner (vendor=0x03f0 [Hewlett-Packard], product=0x0605 [HP ScanJet 2200C], chip=LM9832/3) at libusb:003:003 found USB scanner (vendor=0x05e1, product=0x0501) at libusb:001:003 What are the results of running scanimage --list-devices both as root and a normal user? Permission problems can cause scanimage or xsane to not find the scanner while sane-find-scanner will. -- Neil Bothwick What do you have when you have six lawyers buried up to their necks in sand? Not enough sand. signature.asc Description: PGP signature
Re: [gentoo-user] Need help networking two machines.
Dale wrote: Hi I have done this before. Maybe something has changed because I can not get it to work now. My main rig is called smoker. The second rig is currently booted off the CD. I plan to use my main rig to sync and get distfiles off of. This is off smokers /etc/conf.d/net file: config_eth0=( 192.168.0.1 netmask 255.255.255.0 broadcast 192.168.0.255 ) More info from smoker: eth0 Link encap:Ethernet HWaddr 00:01:53:81:00:E7 inet addr:192.168.0.1 Bcast:192.168.0.255 Mask:255.255.255.0 UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:34 errors:0 dropped:0 overruns:0 frame:0 TX packets:205 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:16458 (16.0 Kb) TX bytes:5670 (5.5 Kb) Interrupt:10 Base address:0xc000 [EMAIL PROTECTED] / # ping 192.168.0.2 PING 192.168.0.2 (192.168.0.2) 56(84) bytes of data. From 192.168.0.1 icmp_seq=1 Destination Host Unreachable From 192.168.0.1 icmp_seq=2 Destination Host Unreachable From 192.168.0.1 icmp_seq=3 Destination Host Unreachable --- 192.168.0.2 ping statistics --- 5 packets transmitted, 0 received, +3 errors, 100% packet loss, time 4009ms , pipe 3 [EMAIL PROTECTED] / # If it helps any, I see traffic going over the network in gkrellm. [EMAIL PROTECTED] / # route Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface nas2.greenwood1 * 255.255.255.255 UH0 0 0 ppp0 192.168.0.0 * 255.255.255.0 U 0 0 0 eth0 loopback* 255.0.0.0 U 0 00 lo default nas2.greenwood1 0.0.0.0 UG0 0 0 ppp0 [EMAIL PROTECTED] / # Yea, ppp0 would be that slow as crap dial-up connection I have. cries [EMAIL PROTECTED] / # iptables -L Chain INPUT (policy ACCEPT) target prot opt source destination ACCEPT tcp -- anywhere anywheretcp dpt:http DROP all -- anywhere anywherestate INVALID,NEW Chain FORWARD (policy ACCEPT) target prot opt source destination DROP all -- anywhere anywherestate INVALID,NEW Chain OUTPUT (policy ACCEPT) target prot opt source destination [EMAIL PROTECTED] / # Now the info from the second rig is a bit hard to get. I can't exactly copy and paste here. Help me get this working and I'll copy and paste all you want. LOL Second rig is the same setup except it is set to address 192.168.0.2. I did restart the network though, on both rigs. Route returns loopback and that is all. Looks suspicious to me. It doesn't have iptables installed on the CD. I guess there are none. Oh, to test the cable, I set both to the same address. When I tried to bring up the network, it gave me a error that the address was in use or something like that. It saw it at least. Can someone tell me what I am doing wrong? It has to be me. It almost always is. Thanks for the help. Dale :-) :-) :-) Hi, Dale I suspect you don't have a proper module for your network card loaded into the kernel. Is the interface of rig-2 up? What does ifconfig eth0 say? -- Best regards, Daniel -- gentoo-user@gentoo.org mailing list
[gentoo-user] Portage Emerge Net Connect Error
Everytime I attempt to install a new program using portage i get this error: Resolving distfiles.gentoo.org... failed: Temporary failure in name resolution. I do have internet access and I am writing this email from the same machine. It doesn't matter what package or when i get this error all the time. Even on the other mirrors for the package. -- Ryan Crisman
Re: [gentoo-user] Portage Emerge Net Connect Error
Ryan Crisman wrote: Everytime I attempt to install a new program using portage i get this error: Resolving distfiles.gentoo.org... failed: Temporary failure in name resolution. I do have internet access and I am writing this email from the same machine. It doesn't matter what package or when i get this error all the time. Even on the other mirrors for the package. Well, for some reason dns lookup for those sites fail. What happens when you put distfiles.gentoo.org in a web browser? You could also try pinging the repositories first, and if they get though, try emerge again. If emerge still fails, I'd try adding them to the host file with whatever ip you get from pinging as a workaround. PaulNM -- gentoo-user@gentoo.org mailing list
RE: [gentoo-user] Portage Emerge Net Connect Error
-Original Message- From: Ryan Crisman [mailto:[EMAIL PROTECTED] Sent: 12 January 2007 14:11 To: gentoo-user@lists.gentoo.org Subject: [gentoo-user] Portage Emerge Net Connect Error Everytime I attempt to install a new program using portage i get this error: Resolving distfiles.gentoo.org... failed: Temporary failure in name resolution. I do have internet access and I am writing this email from the same machine. It doesn't matter what package or when i get this error all the time. Even on the other mirrors for the package. Can you try doing ping www.google.com at the command line? Does that work? If not check /etc/resolv.conf as with some routers you need to manually specify DNS servers in /etc/resolv.conf. Cheers David Note: These views are my own, advice is provided with no guarantee of success. I do not represent anyone else in any emails I send to this list.
Re: [gentoo-user] Portage Emerge Net Connect Error
I do a ping distfiles.gentoo.org ping: unknown host distfiles.gentoo.org Than i try and ping its ip and i get connect: network is unreachable Pinging www.Google.com: connect: network is unreachable contents of resolv.conf domain localdomain nameserver 192.168.1.1 nameserver 192.168.1.1 But as i said before I am able to browser the web in Firefox. On 1/12/07, PaulNM [EMAIL PROTECTED] wrote: Ryan Crisman wrote: Everytime I attempt to install a new program using portage i get this error: Resolving distfiles.gentoo.org... failed: Temporary failure in name resolution. I do have internet access and I am writing this email from the same machine. It doesn't matter what package or when i get this error all the time. Even on the other mirrors for the package. Well, for some reason dns lookup for those sites fail. What happens when you put distfiles.gentoo.org in a web browser? You could also try pinging the repositories first, and if they get though, try emerge again. If emerge still fails, I'd try adding them to the host file with whatever ip you get from pinging as a workaround. PaulNM -- gentoo-user@gentoo.org mailing list -- Ryan Crisman
Re: [gentoo-user] Portage Emerge Net Connect Error
Okay i got it to work. It turns out /etc/conf.d/net was not setup to see the router. I just looked it up on the Gentoo Linux Doc and routes_eth0 was not set up so I added routes_eth0=default gw 192.168.1.1 to the end of the file, restarted eth0 and everything works now. Thanks for the help. On 1/12/07, Ryan Crisman [EMAIL PROTECTED] wrote: I do a ping distfiles.gentoo.org ping: unknown host distfiles.gentoo.org Than i try and ping its ip and i get connect: network is unreachable Pinging www.Google.com: connect: network is unreachable contents of resolv.conf domain localdomain nameserver 192.168.1.1 nameserver 192.168.1.1 But as i said before I am able to browser the web in Firefox. On 1/12/07, PaulNM [EMAIL PROTECTED] wrote: Ryan Crisman wrote: Everytime I attempt to install a new program using portage i get this error: Resolving distfiles.gentoo.org... failed: Temporary failure in name resolution. I do have internet access and I am writing this email from the same machine. It doesn't matter what package or when i get this error all the time. Even on the other mirrors for the package. Well, for some reason dns lookup for those sites fail. What happens when you put distfiles.gentoo.org in a web browser? You could also try pinging the repositories first, and if they get though, try emerge again. If emerge still fails, I'd try adding them to the host file with whatever ip you get from pinging as a workaround. PaulNM -- gentoo-user@gentoo.org mailing list -- Ryan Crisman -- Ryan Crisman
RE: [gentoo-user] Portage Emerge Net Connect Error
- Original Message- From: Ryan Crisman [mailto:[EMAIL PROTECTED] Sent: 12 January 2007 14:45 To: gentoo-user@lists.gentoo.org Subject: Re: [gentoo-user] Portage Emerge Net Connect Error I do a ping distfiles.gentoo.org ping: unknown host distfiles.gentoo.org Than i try and ping its ip and i get connect: network is unreachable Pinging www.Google.com: connect: network is unreachable contents of resolv.conf domain localdomain nameserver 192.168.1.1 nameserver 192.168.1.1 But as i said before I am able to browser the web in Firefox. Try my suggestion. Manually specify nameservers in /etc/resolv.conf. I have had the same problem before. Web browsers and the like work happily but console based programs do not. David Note: These views are my own, advice is provided with no guarantee of success. I do not represent anyone else in any emails I send to this list.
Re: [gentoo-user] Portage Emerge Net Connect Error
On 12 January 2007 16:45, Ryan Crisman wrote: I do a ping distfiles.gentoo.org ping: unknown host distfiles.gentoo.org Than i try and ping its ip and i get connect: network is unreachable Pinging www.Google.com: connect: network is unreachable contents of resolv.conf domain localdomain nameserver 192.168.1.1 nameserver 192.168.1.1 But as i said before I am able to browser the web in Firefox. And you are writing your email also in your browser, right? Taking all the above into account, the conclusion is: 1. Your browser is configured to use a proxy, and the proxy server is given by IP address. 2. Your box lacks a default route. It's a logical AND between 1. and 2. ;-) Uwe -- A fast and easy generator of fractals for KDE: http://www.SysEx.com.na/iwy-1.0.tar.bz2 Proof of concept of a TSP solver for KDE: http://www.SysEx.com.na/epat-0.1.tar.bz2 -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Re: CTRL-ALT-NUM+
David; I'm having the exact same problems on one of my computers since I upgraded to the latest X. I simply haven't gotten around to doing much trouble shooting since I don't use that system very often. Thanks for posting your solution, I'm gonna try this out later. Adrian On Thu, 11 Jan 2007 21:27:11 -0500 David Corbin [EMAIL PROTECTED] wrote the words: Success, but I can't explain it all. First, I removed 'Option XkbVariant nodeadkeys ' from xorg.conf. That got the VT working and the Zooming. But ALT-TAB wasn't working at all. Now, earlier I had problems with the WIN key not working for me as I wanted it to, and adde some xmodmap entires for the WIN key (but not the ALT key). Still, I got suspicous, and took those out, but the XkbVariant back, and now everything including the WIN key is working. -- gentoo-user@gentoo.org mailing list -- On The Fly Photography -:- Creation From Chaos On The Fly Photography: http://204EastSouth.com Purchase from On The Fly: http://204EastSouth.com/OTFStore.htm The Cynical Libertarian Society: http://www.204EastSouth.com/cls -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] [OT] Top/Bottom Posting
On Thu, 11 Jan 2007, Iain Buchanan wrote: On Wed, 2007-01-10 at 10:40 -0300, Arturo 'Buanzo' Busleiman wrote: Many mail readers (e.g Thunderbird) put the signature (that means, the text after a \r\n--\r\n token) in a different, lighter color. actually, I think that's supposed to be dash-dash-space-newline. Thus, replying below the signature may put your reply in the same color, potentially rendering it invisible to some eyes. evolution automatically deletes everything including and below the dash-dash-space-newline when you reply. Which is handy because signatures really should not be quoted in the first place. Quote only what is needed. Text is attributed at the beginning of the quote. Mikko -- Mikko Ruuska, R D Solid Information Technology -- http://www.solidtech.com -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Re: ATI Radeon 9550
James wrote: sean tech.junk at verizon.net writes: I emerged the latest drivers you specified above and -dri stable drivers, these actually compiled. The xorg configure keeps crashing, but I played around with my earlier xorg config. Well, if you like I'll email directly to you my xorg.conf file for my ati-1900. There are numerous differences compared to any of my radeon compatible xorg.conf files... Thanks James, sure. I am actually in the process rebuilding the system from scratch again. Install completed, and things upgraded. Still need to emerge xorg, ati-drivers and related. So which would best be first, xorg, or the ati-drivers? Sean -- gentoo-user@gentoo.org mailing list
[gentoo-user] bug in usermod, full name of options doesn't work
Goal: add gottlieb to group scanner. It seems that -aG works but --append --groups doesn't I will file a bug in b.g.o. unless I did something wrong. thanks in advance allan ajglap portage # usermod --groups scanner --append gottlieb Usage: usermod [options] LOGIN Options: -a, --append append the user to the supplemental GROUPS (use only with -G) -c, --comment COMMENT new value of the GECOS field -d, --home HOME_DIR new home directory for the user account -e, --expiredate EXPIRE_DATE set account expiration date to EXPIRE_DATE -f, --inactive INACTIVE set password inactive after expiration to INACTIVE -g, --gid GROUP force use GROUP as new primary group -G, --groups GROUPS new list of supplementary GROUPS -h, --helpdisplay this help message and exit -l, --login NEW_LOGIN new value of the login name -L, --locklock the user account -m, --move-home move contents of the home directory to the new location (use only with -d) -o, --non-unique allow using duplicate (non-unique) UID -p, --password PASSWORD use encrypted password for the new password -s, --shell SHELL new login shell for the user account -u, --uid UID new UID for the user account -U, --unlock unlock the user account ajglap portage # usermod -aG scanner gottlieb ajglap portage # grep gottlieb /etc/group wheel:x:10:root,gottlieb cron:x:16:cron,gottlieb audio:x:18:gottlieb cdrom:x:19:haldaemon,gottlieb video:x:27:root,gottlieb games:x:35:gottlieb cdrw:x:80:gottlieb,haldaemon portage:x:250:portage,gottlieb gottlieb:x:1502: scanner:x:1504:gottlieb plugdev:x:1507:gottlieb,haldaemon -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Need help networking two machines.
Daniel Iliev wrote: Dale wrote: Hi I have done this before. Maybe something has changed because I can not get it to work now. My main rig is called smoker. The second rig is currently booted off the CD. I plan to use my main rig to sync and get distfiles off of. This is off smokers /etc/conf.d/net file: snip Can someone tell me what I am doing wrong? It has to be me. It almost always is. Thanks for the help. Dale :-) :-) :-) Hi, Dale I suspect you don't have a proper module for your network card loaded into the kernel. Is the interface of rig-2 up? What does ifconfig eth0 say? When I type in ifconfig, it says it is up and running fine with the correct address and all. lsmod shows the module is loaded. It is the correct module as far as I can tell. It's the 8139 module. When I ping from the CD booted computer to smoker, I see data in gkrellm on smoker on eth0. It's getting there. I think iptables is blocking me or something as silly as that. Any ideas? Dale :-) :-) :-) -- www.myspace.com/dalek1967
Re: [gentoo-user] Need help networking two machines.
Dale wrote: Daniel Iliev wrote: Dale wrote: Hi I have done this before. Maybe something has changed because I can not get it to work now. My main rig is called smoker. The second rig is currently booted off the CD. I plan to use my main rig to sync and get distfiles off of. This is off smokers /etc/conf.d/net file: snip Can someone tell me what I am doing wrong? It has to be me. It almost always is. Thanks for the help. Dale :-) :-) :-) Hi, Dale I suspect you don't have a proper module for your network card loaded into the kernel. Is the interface of rig-2 up? What does ifconfig eth0 say? When I type in ifconfig, it says it is up and running fine with the correct address and all. lsmod shows the module is loaded. It is the correct module as far as I can tell. It's the 8139 module. When I ping from the CD booted computer to smoker, I see data in gkrellm on smoker on eth0. It's getting there. I think iptables is blocking me or something as silly as that. Any ideas? Dale :-) :-) :-) -- www.myspace.com/dalek1967 I stole this from here: http://web.onetel.net.uk/~showerail/firewall_disabling.html If its iptables then this should work... iptables -F iptables -t nat -F iptables -P INPUT ACCEPT iptables -P FORWARD ACCEPT iptables -P OUTPUT ACCEPT -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] wine compilation errors
If it isn't luck it seems that some part of portage coused this error. I untared wine tarball from distfiles and I've done everything according to README inside. It compiled successfully. How can I check what part of portage couse this? On 1/9/07, CapSel [EMAIL PROTECTED] wrote: I added en to LINGUAS and I emerged all autoconf and automake ports, m4, bison, binutils, flex, gawk, sed and I get this: ../../tools/winegcc/winegcc -B../../tools/winebuild -shared ./dpnet.specaddr ess.o client.o dpnet_main.o peer.o regsvr.o server.oversion.res -o dpnet.d ll.so -lole32 -luser32 -ladvapi32 -lkernel32 -ldxguid -luuid ../../libs/port/l ibwine_port.a make[2]: Leaving directory `/var/tmp/portage/wine-0.9.22/work/wine-0.9.22/dlls/dpnet' make[2]: Entering directory `/var/tmp/portage/wine-0.9.22/work/wine-0.9.22/dlls/dpnhpast' Makefile:460: warning: NUL character seen; rest of line ignored Makefile:473: warning: NUL character seen; rest of line ignored make[2]: *** No rule to make target `../../include/w', needed by `main.o'. Stop. make[2]: Leaving directory `/var/tmp/portage/wine-0.9.22/work/wine-0.9.22/dlls/dpnhpast' make[1]: *** [dpnhpast] Error 2 make[1]: Leaving directory `/var/tmp/portage/wine-0.9.22/work/wine-0.9.22/dlls' make: *** [dlls] Error 2 !!! ERROR: app-emulation/wine-0.9.22 failed. Call stack: ebuild.sh, line 1546: Called dyn_compile ebuild.sh, line 937: Called src_compile wine-0.9.22.ebuild, line 111: Called die !!! all !!! If you need support, post the topmost build error, and the call stack if relevant. It looks like this is error in random Makefile, there are series of dots on black background when I look at mcedit and less shows [EMAIL PROTECTED] What else can couse these errors? On 1/8/07, Richard Fish [EMAIL PROTECTED] wrote: On 1/7/07, CapSel [EMAIL PROTECTED] wrote: ... what else can I do? I don't see anything obviously wrong. It looks like the problem appears when autoconf/automake are run to generate the Makefiles. Searching bugzilla for similar things leads me to believe that the nls USE flag and non-english language settings could have an effect here. Another similar bug was traced to the version of sed being used, but that was quite old. However, all of the relevant bugs seem quite old. Still, you might try: LINGUAS=en en_US emerge wine If it is still broke, take a look at (and/or post) /var/tmp/portage/wine-0.9.22/work/wine-0.9.22/dlls/oleaut32/Makefile -Richard -- gentoo-user@gentoo.org mailing list -- gentoo-user@gentoo.org mailing list
[gentoo-user] Problems with Hal compilation (after Dbus update)
-BEGIN PGP SIGNED MESSAGE- Hash: SHA1 The full listing can be found here: http://gentoo.pastebin.ca/314398 -BEGIN PGP SIGNATURE- Version: GnuPG v1.4.5 (GNU/Linux) Comment: Using GnuPG with Mozilla - http://enigmail.mozdev.org iD8DBQFFp+nVhd3kS+HiI0sRAt8hAJ44td0J13R3NZwMt7kWr/w6VN0yPACeNs9Y vTM8WkQZFtt8+87fnQyXsjo= =OLE4 -END PGP SIGNATURE- -- gentoo-user@gentoo.org mailing list
[gentoo-user] telling hpaio / sane what scanners are present
Two problems identifying scanners ajglap ~ # scanimage -L device `hpaio:/usb/HP_LaserJet_1200?device=/dev/usb/lp0' is a hp HP_LaserJet_1200 multi-function peripheral ajglap ~ # This is wrong. I do indeed have HP laserjet 1200 attached via usb, but it is a printer not a multifunction device. The second problem is that there is on the network (at location 192.168.1.50) a real multifunction device, HP officejet 7310. This is not found. Add'l info When at another location with no laserjet but with a USB multifunction device (officejet 7130 -- not 7310), all is well. If at the original site I try scanimage without -L, it faults (see below). thanks in advance for any help, allan ajglap ~ # scanimage *** glibc detected *** scanimage: munmap_chunk(): invalid pointer: 0xb7dd8391 *** === Backtrace: = /lib/libc.so.6[0xb7e4abab] /usr/lib/sane/libsane-hpaio.so.1(sane_hpaio_open+0x28d)[0xb7dceb09] /usr/lib/libsane.so.1(sane_dll_open+0xde)[0xb7fc1e36] /usr/lib/libsane.so.1(sane_open+0x24)[0xb7fc24c9] scanimage[0x804ba26] /lib/libc.so.6(__libc_start_main+0xdc)[0xb7dff864] scanimage[0x80491e1] === Memory map: 08048000-08051000 r-xp 16:03 803995 /usr/bin/scanimage 08051000-08052000 rw-p 8000 16:03 803995 /usr/bin/scanimage 08052000-08073000 rw-p 08052000 00:00 0 [heap] b7c72000-b7c7b000 r-xp 16:03 670542 /usr/lib/gcc/i686-pc-linux-gnu/4.1.1/libgcc_s.so.1 b7c7b000-b7c7c000 rw-p 8000 16:03 670542 /usr/lib/gcc/i686-pc-linux-gnu/4.1.1/libgcc_s.so.1 b7c7c000-b7d8f000 r-xp 16:03 1112290/usr/lib/libcrypto.so.0.9.8 b7d8f000-b7da4000 rw-p 00113000 16:03 1112290/usr/lib/libcrypto.so.0.9.8 b7da4000-b7da7000 rw-p b7da4000 00:00 0 b7da7000-b7dc6000 r-xp 16:03 364633 /usr/lib/libhpip.so.0.0.1 b7dc6000-b7dc7000 rw-p 0001e000 16:03 364633 /usr/lib/libhpip.so.0.0.1 b7dc7000-b7dc9000 rw-p b7dc7000 00:00 0 b7dc9000-b7ddf000 r-xp 16:03 364636 /usr/lib/libsane-hpaio.so.1.0.0 b7ddf000-b7de rw-p 00015000 16:03 364636 /usr/lib/libsane-hpaio.so.1.0.0 b7de-b7de2000 rw-p b7de 00:00 0 b7de2000-b7de9000 r-xp 16:03 1112285/usr/lib/libieee1284.so.3.0.4 b7de9000-b7dea000 rw-p 6000 16:03 1112285/usr/lib/libieee1284.so.3.0.4 b7dea000-b7efa000 r-xp 16:03 278468 /lib/libc-2.4.so b7efa000-b7efc000 r--p 0010f000 16:03 278468 /lib/libc-2.4.so b7efc000-b7efe000 rw-p 00111000 16:03 278468 /lib/libc-2.4.so b7efe000-b7f01000 rw-p b7efe000 00:00 0 b7f01000-b7f23000 r-xp 16:03 278469 /lib/libm-2.4.so b7f23000-b7f25000 rw-p 00021000 16:03 278469 /lib/libm-2.4.so b7f25000-b7f36000 r-xp 16:03 278474 /lib/libz.so.1.2.3 b7f36000-b7f37000 rw-p 0001 16:03 278474 /lib/libz.so.1.2.3 b7f37000-b7f55000 r-xp 16:03 1116899/usr/lib/libjpeg.so.62.0.0 b7f55000-b7f56000 rw-p 0001d000 16:03 1116899/usr/lib/libjpeg.so.62.0.0 b7f56000-b7f57000 rw-p b7f56000 00:00 0 b7f57000-b7fa6000 r-xp 16:03 375117 /usr/lib/libtiff.so.3.8.2 b7fa6000-b7fa8000 rw-p 0004f000 16:03 375117 /usr/lib/libtiff.so.3.8.2 b7fa8000-b7fb7000 r-xp 16:03 278472 /lib/libpthread-2.4.so b7fb7000-b7fb8000 r--p e000 16:03 278472 /lib/libpthread-2.4.so b7fb8000-b7fb9000 rw-p f000 16:03 278472 /lib/libpthread-2.4.so b7fb9000-b7fbb000 rw-p b7fb9000 00:00 0 b7fbb000-b7fbd000 r-xp 16:03 278471 /lib/libdl-2.4.so b7fbd000-b7fbf000 rw-p 1000 16:03 278471 /lib/libdl-2.4.so b7fbf000-b7fc4000 r-xp 16:03 1112511/usr/lib/libsane.so.1.0.18 b7fc4000-b7fc5000 rw-p 4000 16:03 1112511/usr/lib/libsane.so.1.0.18 b7fd8000-b7fd9000 rw-p b7fd8000 00:00 0 b7fd9000-b7fda000 r-xp b7fd9000 00:00 0 [vdso] b7fda000-b7ff3000 r-xp 16:03 278465 /lib/ld-2.4.so b7ff3000-b7ff4000 r--p 00019000 16:03 278465 /lib/ld-2.4.so b7ff4000-b7ff5000 rw-p 0001a000 16:03 278465 /lib/ld-2.4.so bf89c000-bf8b2000 rw-p bf89c000 00:00 0 [stack] Aborted ajglap ~ # -- gentoo-user@gentoo.org mailing list
[gentoo-user] compiling r1000 module
I try to compile the r1000 module for my laptop. asus ~ # uname -r 2.6.18-xen asus ~ # tar xzf r1000_v1.05.tgz asus ~ # cd r1000_v1.05 asus r1000_v1.05 # make clean modules make -C src/ clean make[1]: Entering directory `/root/r1000_v1.05/src' rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions make[1]: Leaving directory `/root/r1000_v1.05/src' make -C src/ modules make[1]: Entering directory `/root/r1000_v1.05/src' make -C /lib/modules/2.6.18-xen/build SUBDIRS=/root/r1000_v1.05/src modules make[2]: Entering directory `/lib64/modules/2.6.18-xen/build' make[2]: *** No rule to make target `modules'. Stop. make[2]: Leaving directory `/lib64/modules/2.6.18-xen/build' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/root/r1000_v1.05/src' make: *** [modules] Error 2 asus r1000_v1.05 # On normal 2.6.18 (without Xen), it is OK. Would you help me to find the problem? -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] compiling r1000 module
Hi, On Fri, 12 Jan 2007 22:46:02 +0100 Mihamina Rakotomandimby (R12y) [EMAIL PROTECTED] wrote: I try to compile the r1000 module for my laptop. [...] make[2]: *** No rule to make target `modules'. Stop. You don't compile 2.6 kernel modules with make modules. Just use make, then probably sudo make install. -hwh -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] usb scanner HP2200c
On Fri, 2007-01-12 at 10:19 +, Neil Bothwick wrote: What are the results of running scanimage --list-devices both as root and a normal user? Permission problems can cause scanimage or xsane to not find the scanner while sane-find-scanner will. As root: # scanimage --list-devices No scanners were identified. [...] # sane-find-scanner -q found USB scanner [...] found USB scanner [...] As normal user: $ scanimage --list-devices No scanners were identified. $ sane-find-scanner -q found USB scanner [...] found USB scanner [...] I know my scanner uses plustek driver, and I already edited /etc/sane.d/plustek.conf, but I dont know how to exclude all other configuration files so that they dont disturb mine... PS: Sorry for the CCing, just to up the thread. -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Problems with Hal compilation (after Dbus update)
Hi, On Fri, 12 Jan 2007 20:04:37 + Avaricen [EMAIL PROTECTED] wrote: The full listing can be found here: http://gentoo.pastebin.ca/314398 Just because you're using a browser to read and write mail, don't assume others do. Trim down the output to the relevant part (here: some dbus functions aren't found, compile fails) and put it in your mail, and ask the question you want to be answered. My suggestion: run revdep-rebuild, but maybe re-emerging dbus and hal is enough. -hwh -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] compiling r1000 module
On Fri, 2007-01-12 at 23:04 +0100, Hans-Werner Hilse wrote: Hi, On Fri, 12 Jan 2007 22:46:02 +0100 Mihamina Rakotomandimby (R12y) [EMAIL PROTECTED] wrote: I try to compile the r1000 module for my laptop. [...] make[2]: *** No rule to make target `modules'. Stop. You don't compile 2.6 kernel modules with make modules. Just use make, then probably sudo make install. asus ~ # cd r1000_v1.05 asus r1000_v1.05 # make make -C src/ clean make[1]: Entering directory `/root/r1000_v1.05/src' rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions make[1]: Leaving directory `/root/r1000_v1.05/src' make -C src/ modules make[1]: Entering directory `/root/r1000_v1.05/src' make -C /lib/modules/2.6.18-xen/build SUBDIRS=/root/r1000_v1.05/src modules make[2]: Entering directory `/lib64/modules/2.6.18-xen/build' make[2]: *** No rule to make target `modules'. Stop. make[2]: Leaving directory `/lib64/modules/2.6.18-xen/build' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/root/r1000_v1.05/src' make: *** [modules] Error 2 Anyway, I am following this howto: http://gentoo-wiki.com/HARDWARE_RTL8168 And this method worked on my normal kernel... -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] usb scanner HP2200c
On AD 2007 January 12 Friday 11:12:57 PM +0100, Mihamina Rakotomandimby (R12y) wrote: On Fri, 2007-01-12 at 10:19 +, Neil Bothwick wrote: What are the results of running scanimage --list-devices both as root and a normal user? Permission problems can cause scanimage or xsane to not find the scanner while sane-find-scanner will. As root: # scanimage --list-devices No scanners were identified. [...] # sane-find-scanner -q found USB scanner [...] found USB scanner [...] As normal user: $ scanimage --list-devices No scanners were identified. $ sane-find-scanner -q found USB scanner [...] found USB scanner [...] I don't have much experience with USB devices or how udev handles them in /dev. All my experience which is quite limited would suggest that it is still a permission issue. You could find the (ephemeral) device file(s) and check the perms on them and then issue the groups command to check against. My guess is you still have a permission problem that is more likely due to /etc/groups than to /etc/udev.d. Justin -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] usb scanner HP2200c
I don't have much experience with USB devices or how udev handles them in /dev. All my experience which is quite limited would suggest that it is still a permission issue. You could find the (ephemeral) device file(s) and check the perms on them and then issue the groups command to check against. My guess is you still have a permission problem that is more likely due to /etc/groups than to /etc/udev.d you may have to relogin as your user to apply the new group settings; you may also have to be in the USB group; you may also have to unplug and replug the scanner once after you add yourself to those groups. Just to be clear, I use Xsane and an HP Scanjet, i think 4300 C, something close to that, and permission issues like this don't effect root, so that would be agood way to test. -- gentoo-user@gentoo.org mailing list
[gentoo-user] Re: ATI Radeon 9550
sean tech.junk at verizon.net writes: I am actually in the process rebuilding the system from scratch again. Install completed, and things upgraded. I'll email my xorg.conf that works with my ati-1900 as a reference. So which would best be first, xorg, or the ati-drivers? Um, I'm not sure it matters. Try ati-drivers first and it may want to pull in xorg first. In that case, the answer is org. If not, it does not matter. Remember, at some point, after you build a kernel, you have to run modules-update, but surf the various gentoo web pages on Ati to get that answer. follow the main gentoo web page: http://www.gentoo.org/doc/en/xorg-config.xml http://odin.prohosting.com/wedge01/gentoo-radeon-faq.html this last pages says that your 9550 card is supported by the ati-binary driver. I'll try and help you thru this, but, realize I'm not whiz at ati-driver obscurity issues. That said, keep a precise log of what you do, what fails and what works, and maybe between us, we can develop a simple ascii text file that works and is current. I'll be back online in 3-4 hours to check your progress. Hang in there, James -- gentoo-user@gentoo.org mailing list
[gentoo-user] managing 802.11a/b/g
Hello, I managed to intall madwifi-ng, wpa_supplicant and rebuild the kernel with cryto, so far. The hardware in this protable is: 02:00.0 Ethernet controller: Atheros Communications, Inc. AR5212 802.11abg NIC (rev 01 wifi0 Link encap:UNSPEC HWaddr 00-18-4D-4C-0C-9B-7B-B6-00-00-00-00-00-00-00-00 BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:199 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:5 Memory:faa8-faa9 My question is there a gui to manage the wireless connection and should I add an iptables script to secure the machine when accessing variouls networks with 802.11? Also, does any gui manage/control the dhcp handshaking that occurs at various location, which is the same gui that monitors/manages the wireless connect and firewall(iptables)? possibility would be a wireless (static) ip at site where access occurs frequently in lieu of dhcp. Is that a gui that one can use to manages all of the various common configuration choices, or is it a roll_your_own type of management for 802.11 type devices. Googling does not produce much: http://gentoo-wiki.com/HOWTO_Wireless_Configuration_and_Startup http://gentoo-wiki.com/HARDWARE_Wireless http://gentoo-wiki.com/HARDWARE_ar5212 that is specifically related to managing and using the wireless interface. James -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Re: CTRL-ALT-NUM+
On Thursday 11 January 2007 22:39, Avaricen wrote: David Corbin wrote: Success, but I can't explain it all. First, I removed 'Option XkbVariant nodeadkeys ' from xorg.conf. That got the VT working and the Zooming. But ALT-TAB wasn't working at all. Now, earlier I had problems with the WIN key not working for me as I wanted it to, and adde some xmodmap entires for the WIN key (but not the ALT key). Still, I got suspicous, and took those out, but the XkbVariant back, and now everything including the WIN key is working. Nice to know you got it working alright, did you modify your xorg.conf? I did modify it in an attempt to solve the problem, but the problem showed up without me making any such modifications that I'm aware of. Was this problem since your inception to Gentoo? No, I've been running Gentoo on this system for 2 3/4 years. I've been using these keystrokes for over a year. I upgraded to X11 7.x a few months ago. -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Re: CTRL-ALT-NUM+
On Friday 12 January 2007 10:40, Adrian wrote: David; I'm having the exact same problems on one of my computers since I upgraded to the latest X. I simply haven't gotten around to doing much trouble shooting since I don't use that system very often. Thanks for posting your solution, I'm gonna try this out later. If you call it a solution :) From my perspective, it's magic. -- gentoo-user@gentoo.org mailing list
[gentoo-user] Packages from overlays
Hi list, Is there a way of finding out whether I have packages installed on my system from a given overlay? I am asking because I noticed that some of the packages I've installed (such as GoogleEarth) from overlays had been incorporated into the official portage. I would like to 'unsubscribe' to overlays that doesn't have packages that I need. Thanks, Willie -- Will will will unless Will wills willingly. Maybe Willow ~tiredwired. Sunday Oct. 6. 6:00pm Sortir en Pantoufles: up 35 days, 23:04 -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] managing 802.11a/b/g
James wrote: Also, does any gui manage/control the dhcp handshaking that occurs at various location, which is the same gui that monitors/manages the wireless connect and firewall(iptables)? possibility would be a wireless (static) ip at site where access occurs frequently in lieu of dhcp. Is that a gui that one can use to manages all of the various common configuration choices, or is it a roll_your_own type of management for 802.11 type devices. If you can use NetworkManager you'll find it rocks. I use it on Fedora and I'm no longer jealous of Mac and Windows users and their ability to use a random AP on a moment's notice. http://www.gnome.org/projects/NetworkManager/ Regards, Cliff -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] compiling r1000 module
On 1/12/07, Mihamina Rakotomandimby (R12y) [EMAIL PROTECTED] wrote: On Fri, 2007-01-12 at 23:04 +0100, Hans-Werner Hilse wrote: Hi, On Fri, 12 Jan 2007 22:46:02 +0100 Mihamina Rakotomandimby (R12y) [EMAIL PROTECTED] wrote: I try to compile the r1000 module for my laptop. [...] make[2]: *** No rule to make target `modules'. Stop. You don't compile 2.6 kernel modules with make modules. Just use make, then probably sudo make install. asus ~ # cd r1000_v1.05 asus r1000_v1.05 # make make -C src/ clean make[1]: Entering directory `/root/r1000_v1.05/src' rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions make[1]: Leaving directory `/root/r1000_v1.05/src' make -C src/ modules make[1]: Entering directory `/root/r1000_v1.05/src' make -C /lib/modules/2.6.18-xen/build SUBDIRS=/root/r1000_v1.05/src modules make[2]: Entering directory `/lib64/modules/2.6.18-xen/build' make[2]: *** No rule to make target `modules'. Stop. make[2]: Leaving directory `/lib64/modules/2.6.18-xen/build' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/root/r1000_v1.05/src' make: *** [modules] Error 2 Anyway, I am following this howto: http://gentoo-wiki.com/HARDWARE_RTL8168 And this method worked on my normal kernel... -- gentoo-user@gentoo.org mailing list I use the driver shown in this link and it works for me. but I don´t know if its in the xen kernel. -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] compiling r1000 module
On 1/13/07, Jakob [EMAIL PROTECTED] wrote: On 1/12/07, Mihamina Rakotomandimby (R12y) [EMAIL PROTECTED] wrote: On Fri, 2007-01-12 at 23:04 +0100, Hans-Werner Hilse wrote: Hi, On Fri, 12 Jan 2007 22:46:02 +0100 Mihamina Rakotomandimby (R12y) [EMAIL PROTECTED] wrote: I try to compile the r1000 module for my laptop. [...] make[2]: *** No rule to make target `modules'. Stop. You don't compile 2.6 kernel modules with make modules. Just use make, then probably sudo make install. asus ~ # cd r1000_v1.05 asus r1000_v1.05 # make make -C src/ clean make[1]: Entering directory `/root/r1000_v1.05/src' rm -rf *.o *.ko *~ core* .dep* .*.d .*.cmd *.mod.c *.a *.s .*.flags .tmp_versions make[1]: Leaving directory `/root/r1000_v1.05/src' make -C src/ modules make[1]: Entering directory `/root/r1000_v1.05/src' make -C /lib/modules/2.6.18-xen/build SUBDIRS=/root/r1000_v1.05/src modules make[2]: Entering directory `/lib64/modules/2.6.18-xen/build' make[2]: *** No rule to make target `modules'. Stop. make[2]: Leaving directory `/lib64/modules/2.6.18-xen/build' make[1]: *** [modules] Error 2 make[1]: Leaving directory `/root/r1000_v1.05/src' make: *** [modules] Error 2 Anyway, I am following this howto: http://gentoo-wiki.com/HARDWARE_RTL8168 And this method worked on my normal kernel... -- gentoo-user@gentoo.org mailing list I use the driver shown in this link and it works for me. but I don´t know if its in the xen kernel. oops sorry I forgot the link, I shall go to bed now http://gentoo-wiki.com/HARDWARE_Asus_F3JM#LAN -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Re: CTRL-ALT-NUM+
On Fri, 12 Jan 2007 19:41:32 -0500 David Corbin [EMAIL PROTECTED] wrote the words: On Friday 12 January 2007 10:40, Adrian wrote: David; I'm having the exact same problems on one of my computers since I upgraded to the latest X. I simply haven't gotten around to doing much trouble shooting since I don't use that system very often. Thanks for posting your solution, I'm gonna try this out later. If you call it a solution :) From my perspective, it's magic. -- I call it strange magic. I had the same problems, Windows keys didn't work and CTR-ALT-F1 would not switch to a VT . . . David said, if I'm reading this right, he had to take nodeadkeys out. Well, I didn't have that options, I added it, and now it works fine. Magic or science, I don't care. I simply want results. This time I got 'em. Odd as it may be This is actually the same xorg.conf which worked fine with X 6.x. It wasn't until I installed X 7 that it got strange on me. Adrian -- On The Fly Photography -:- Creation From Chaos On The Fly Photography: http://204EastSouth.com Purchase from On The Fly: http://204EastSouth.com/OTFStore.htm The Cynical Libertarian Society: http://www.204EastSouth.com/cls -- gentoo-user@gentoo.org mailing list
[gentoo-user] Re: managing 802.11a/b/g
Cliff Wells cliff at develix.com writes: If you can use NetworkManager you'll find it rocks. I use it on Fedora and I'm no longer jealous of Mac and Windows users and their ability to use a random AP on a moment's notice. http://www.gnome.org/projects/NetworkManager/ Hello Cliff, They are all hard masked. Did you install an overlay from somewhere, or just download and compile it? James -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Packages from overlays
Willie Wong wrote: Hi list, Is there a way of finding out whether I have packages installed on my system from a given overlay? I am asking because I noticed that some of the packages I've installed (such as GoogleEarth) from overlays had been incorporated into the official portage. I would like to 'unsubscribe' to overlays that doesn't have packages that I need. Thanks, Willie You may want to reconsider this. I have googleearth installed here and it doesn't get along well with portage and it's digest checking. Of course, it doesn't like my dial-up either. LOL From what I understand Google doesn't allow Gentoo to mirror the souce tarball. After you install it and sync later on, if Google has changed something, you get a digest error. It will delete the tarball from distfiles too. I'm on dial-up and that sort of ticks me off, The way I got around it is to manually delete it from my world file. That way it doesn't check the digest. Some guru may have a better way to do this but this is what I have ran into with googleearth. May want to check farther before you run into the same thing I did. Hope that helps, and makes sense. Sometimes I don't. LOL Dale :-) :-) :-) -- www.myspace.com/dalek1967 -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Packages from overlays
On Saturday 13 January 2007 01:49, Willie Wong wrote: Is there a way of finding out whether I have packages installed on my system from a given overlay? I am asking because I noticed that some of the packages I've installed (such as GoogleEarth) from overlays had been incorporated into the official portage. I would like to 'unsubscribe' to overlays that doesn't have packages that I need. Portage currently does not store any information about where a package was installed from. Therefore the best you can do is manually inspect the output of `eix --installed-overlay`. It will show all packages where the version you have installed exists in any overlay (and you can see if they exist in the tree too). That, however, only implies that they might have been installed from that overlay.. It does require app-portage/eix-0.8.x. Also if you use update-eix-remote you better (re)move the eix database (/var/cache/eix) and regenerate the database with `update-eix` first or you will get a lot of false positives. IOW you need the eix database to only contain installed overlays. -- Bo Andresen pgpYjJuGC9w2B.pgp Description: PGP signature
Re: [gentoo-user] Packages from overlays
On 1/13/07, Dale [EMAIL PROTECTED] wrote:
You may want to reconsider this. I have googleearth installed here and
it doesn't get along well with portage and it's digest checking. Of
course, it doesn't like my dial-up either. LOL
It would appear google has updated their package without changing the
name, and portage has not been notified of this change. If you want it
to work, delete the digest file for it in
${PORTAGE_DIR}/x11-misc/googleearth/files/digest-googleearth-4_beta
and then re-generate it with
ebuild ${PORTAGE_DIR}/x11-misc/googleearth/googleearth-4_beta digest
and that should fix you up. I found it still compiles and runs fine *shrugs*
--
/ent Fredric
(aka theJackal)
--
gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Re: managing 802.11a/b/g
james wrote: Cliff Wells cliff at develix.com writes: If you can use NetworkManager you'll find it rocks. I use it on Fedora and I'm no longer jealous of Mac and Windows users and their ability to use a random AP on a moment's notice. http://www.gnome.org/projects/NetworkManager/ Hello Cliff, They are all hard masked. Did you install an overlay from somewhere, or just download and compile it? I only run gentoo on servers, so I've never had to try to install it there. My laptop runs fedora so it comes shipped by default. I'm not certain why it would be hard masked in Gentoo... maybe it's not 100% compatible with the Gentoo init stuff. I've used it without incident on both FC5 and FC6 and the Ubuntu crowd has apparently been using it for some time as well. Hopefully you can get it working because frankly there's not even a close second on Linux for doing what it does. Sorry I can't help more. Regards, Cliff -- gentoo-user@gentoo.org mailing list
[gentoo-user] xkbd and libxcb
I am having trouble building x11-misc/xkbd It dies with i686-pc-linux-gnu-gcc -DHAVE_CONFIG_H -I. -I. -I.. -Os -march=pentium-m -ftracer -pipe -DUSE_XFT -I/usr/include/freetype2 -DUSE_XPM -DDEFAULTCONFIG=\/usr/share/xkbd/en_GB.qwerty.xkbd\ -c button.c i686-pc-linux-gnu-gcc -DHAVE_CONFIG_H -I. -I. -I.. -Os -march=pentium-m -ftracer -pipe -DUSE_XFT -I/usr/include/freetype2 -DUSE_XPM -DDEFAULTCONFIG=\/usr/share/xkbd/en_GB.qwerty.xkbd\ -c kb.c i686-pc-linux-gnu-gcc -DHAVE_CONFIG_H -I. -I. -I.. -Os -march=pentium-m -ftracer -pipe -DUSE_XFT -I/usr/include/freetype2 -DUSE_XPM -DDEFAULTCONFIG=\/usr/share/xkbd/en_GB.qwerty.xkbd\ -c libvirtkeys.c /bin/sh ../libtool --mode=link i686-pc-linux-gnu-gcc -Os -march=pentium-m -ftracer -pipe -DUSE_XFT -I/usr/include/freetype2 -DUSE_XPM -DDEFAULTCONFIG=\/usr/share/xkbd/en_GB.qwerty.xkbd\ -o xkbd xkbd.o libXkbd.o box.o button.o kb.o libvirtkeys.o -lX11 -lXtst -lXpm -lXft -lXrender -lfontconfig -lfreetype -lz -lX11 mkdir .libs libtool: link: cannot find the library `/usr/lib/libxcb-xlib.la' make[2]: *** [xkbd] Error 1 make[2]: Leaving directory `/tmp/portage/x11-misc/xkbd-0.8.12/work/xkbd-0.8.12/src' make[1]: *** [all-recursive] Error 1 make[1]: Leaving directory `/tmp/portage/x11-misc/xkbd-0.8.12/work/xkbd-0.8.12' make: *** [all-recursive-am] Error 2 Now, I don't think xkbd strictly needs libxcb (it builds just fine on my other computer which has an older version of libX11 with no XCB support), so I think that *something* is screwed up with this computer. For background, I orignally installed libX11-1.1.1 with the xcb useflag on, thinking that it wouldn't hurt. Then it turns out some other program (outside portage) does not play well with libxcb, so I turned it off and recompiled. It seems to me that my computer somehow got the idea that -lX11 should still link to libxcb_xlib Can anybody help? Thanks, W -- Once you've seen one shopping center you've seen a mall. Sortir en Pantoufles: up 36 days, 3:00 -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Packages from overlays
Doesn't really seem to be related to OPs question so it probably should have been a new thread, however... On Saturday 13 January 2007 05:15, Dale wrote: [SNIP] From what I understand Google doesn't allow Gentoo to mirror the souce tarball. After you install it and sync later on, if Google has changed something, you get a digest error. The real issue is that google refuse to rename the tarball when they release a new version. The secondary issue is then that Gentoo can't rename it on their own mirros since they aren't allowed to redistribute it. It will delete the tarball from distfiles too. Without your consent?? I'm on dial-up and that sort of ticks me off, Understandable. You should, however, realize that it is an actual upgrade you're rejecting in this case. The way I got around it is to manually delete it from my world file. That way it doesn't check the digest. Some guru may have a better way to do this but this is what I have ran into with googleearth. May want to check farther before you run into the same thing I did. I don't really have a better suggestion if you don't want the upgrades. Redigesting it as Kent suggests seems rather pointless as you would just be reinstalling the old version (while tricking portage into believing you get the newer version (as if that mattered ;)) with no actual gain. -- Bo Andresen pgptbM97Cri9i.pgp Description: PGP signature
Re: [gentoo-user] Packages from overlays
On Sat, Jan 13, 2007 at 05:22:27AM +0100, Penguin Lover Bo ?rsted Andresen squawked: Portage currently does not store any information about where a package was installed from. Therefore the best you can do is manually inspect the output of `eix --installed-overlay`. It will show all packages where the version you have installed exists in any overlay (and you can see if they exist in the tree too). That, however, only implies that they might have been installed from that overlay.. Oh, that is too bad. I think I can live with having extra overlays living on my testing box. Just a thought though: would the following be advisable/work? Could I just delete those relevant overlays (either layman -d or perhaps commenting them out in the relevant parts of the make.confs) and see if emerge complains about non-existant packages in my world file or unsatisfiable dependency? IIRC, I shouldn't have any packages installed from overlays for more recent versions than portage offered; I only install them from overlays when the ebuilds are not in portage at all. W -- This is not an optical illusion. It just looks like one. Sortir en Pantoufles: up 36 days, 3:22 -- gentoo-user@gentoo.org mailing list
[gentoo-user] Re: managing 802.11a/b/g
In news:[EMAIL PROTECTED], Cliff Wells [EMAIL PROTECTED] wrote: I'm not certain why it would be hard masked in Gentoo... maybe it's not 100% compatible with the Gentoo init stuff. I've used it without incident on both FC5 and FC6 and the Ubuntu crowd has apparently been using it for some time as well. Hopefully you can get it working because frankly there's not even a close second on Linux for doing what it does. I read caillon's blog, and I've been excited about NetworkManager since I saw it announced there. I'm still too chicken to install it on a Gentoo system, though. Probably bug 154497 is enough to keep it hard masked. Reading through its bugs gives some good ideas about how to avoid problems, for anyone who wants to give it a try. http://bugs.gentoo.org/buglist.cgi?quicksearch=networkmanager -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] [SOLVED] xkbd and libxcb
On Fri, Jan 12, 2007 at 11:55:35PM -0500, Penguin Lover Willie Wong squawked: I am having trouble building x11-misc/xkbd Oh, don't you hate it when a stroke of genius strikes right after you asked a silly question? Anyway, it occured to me that even though libX11 is no longer linked against libxcb, some other libraries which I haven't rebuilt after rebuilding libX11 might (though is this a bug in portage? I think that either revdep-rebuild should rebuild those packages OR that emerge --depclean shouldn't have removed libxcb). After rebuilding libXpm, libXtst and libXft (I don't actually know which one is the culprit, I just rebuild all the other X related libraries that appeared on the problematic invocation), xkbd now builds fine. Sorry for the noise. W -- ((12 + 144 + 20 + (3 * 4^(1/2))) / 7) + (5 * 11) = 9^2 + 0 A Dozen, a Gross and a Score, plus three times the square root of four, divided by seven, plus five times eleven, equals nine squared and not a bit more. Sortir en Pantoufles: up 36 days, 3:28 -- gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Packages from overlays
On Saturday 13 January 2007 06:09, Willie Wong wrote: Oh, that is too bad. Unless you have a lot of overlays it not really *that* bad. [SNIP] Just a thought though: would the following be advisable/work? Could I just delete those relevant overlays (either layman -d or perhaps commenting them out in the relevant parts of the make.confs) and see if emerge complains about non-existant packages in my world file or unsatisfiable dependency? IIRC, I shouldn't have any packages installed from overlays for more recent versions than portage offered; I only install them from overlays when the ebuilds are not in portage at all. # PORTDIR_OVERLAY= emerge -ep world /dev/null !!! Ebuilds for the following packages are either all !!! masked or don't exist: dev-util/regex-coach app-portage/pfs net-analyzer/ksniffer kde-misc/kcpufreq app-portage/gentoo-stats So yeah, that works. :) IMO the real solution for your problem, however, is a package manager with true multiple repository support allowing you to control from which repository you want to install a given package. I'm not sure if pkgcore is there yet (since I don't follow it too closely), but paludis is. Paludis thus also stores information about which repository a package was installed from. With portage if the same ebuild or eclass exists in any of your overlays and in the tree then the one in the tree will just be hidden to portage behind the overlay. That's why they are called overlays in the first place.. ;) -- Bo Andresen pgpbMtpxNBKso.pgp Description: PGP signature
Re: [gentoo-user] bug in usermod, full name of options doesn't work
On Friday 12 January 2007 18:46, Allan Gottlieb wrote: Goal: add gottlieb to group scanner. It seems that -aG works but --append --groups doesn't I will file a bug in b.g.o. unless I did something wrong. I wouldn't be surprised if it would be RESOLVED UPSTREAM. Guess there's only one way to find out.. I guess you could comment on bug #145416 too (which isn't quite the same issue).. -- Bo Andresen pgpeyQiRqQ2UP.pgp Description: PGP signature
Re: [gentoo-user] Packages from overlays
Kent Fredric wrote:
On 1/13/07, Dale [EMAIL PROTECTED] wrote:
You may want to reconsider this. I have googleearth installed here and
it doesn't get along well with portage and it's digest checking. Of
course, it doesn't like my dial-up either. LOL
It would appear google has updated their package without changing the
name, and portage has not been notified of this change. If you want it
to work, delete the digest file for it in
${PORTAGE_DIR}/x11-misc/googleearth/files/digest-googleearth-4_beta
and then re-generate it with
ebuild ${PORTAGE_DIR}/x11-misc/googleearth/googleearth-4_beta digest
and that should fix you up. I found it still compiles and runs fine
*shrugs*
True, you hit the problem right on the head. That is exactly what they
do. But what I had noticed is that they change that thing a lot. Since
I am on a really slow dial-up here, I check for updates, sync, every
couple days or so. While I know that it comes from Google and I don't
question the tarball from a security point of view, portage still
complains about it each time and deletes it for me, since it thinks it
is a security problem. That would normally be a great idea but then I
have to download it again, which takes a little over two hours for me.
I get about 10Mbs a hour here. goes to have a good cry
Plus, it is a pain in the butt to have to manually do the digest thing
every time I sync up too. My solution was to remove it from the world
file, since portage had already deleted the tarball and I didn't want to
download it again to do a oneshot install. Now the only drawback is
that --depclean -p tells me it is not needed since it is not in the
world file and is not a dependancy. I do that manually anyways so it
doesn't matter.
I'm no guru but if he wants it out of overlay, he may want to emerge it
as a oneshot at least. Then just check for updates on occasion. I had
to use the --digest option too when I installed it. That way it assumes
it is OK and doesnt' check it.
Hope that makes sense. Maybe . . . . LOL
Dale
:-) :-) :-)
--
www.myspace.com/dalek1967
--
gentoo-user@gentoo.org mailing list
Re: [gentoo-user] Packages from overlays
I've gotten this mail twice now. On Saturday 13 January 2007 07:28, Dale wrote: Kent Fredric wrote: It would appear google has updated their package without changing the name, and portage has not been notified of this change. It's the other way around. He gets a digest verification error *because* portage was notified. The old ebuild gets removed because it's tarball is now unavailable upstream (and a new is available under the same name). [SNIP] and that should fix you up. I found it still compiles and runs fine *shrugs* Not much of a fix. Just gets the old version. Of course it still compiles and runs. It hasn't changed at all. [SNIP] While I know that it comes from Google and I don't question the tarball from a security point of view, portage still complains about it each time and deletes it for me, since it thinks it is a security problem. That would normally be a great idea but then I have to download it again, which takes a little over two hours for me. I get about 10Mbs a hour here. [SNIP] I can't help wondering. If you don't have the bandwidth to upgrade when there is an upgrade. How useful is googleearth to you then. It's not like it doesn't require any bandwidth just to run... Also the more often you sync the more bandwidth you need with Gentoo in general.. -- Bo Andresen pgpHX42oCO5zC.pgp Description: PGP signature
Re: [gentoo-user] Packages from overlays
Bo Ørsted Andresen wrote: I've gotten this mail twice now. On Saturday 13 January 2007 07:28, Dale wrote: Kent Fredric wrote: It would appear google has updated their package without changing the name, and portage has not been notified of this change. It's the other way around. He gets a digest verification error *because* portage was notified. The old ebuild gets removed because it's tarball is now unavailable upstream (and a new is available under the same name). [SNIP] and that should fix you up. I found it still compiles and runs fine *shrugs* Not much of a fix. Just gets the old version. Of course it still compiles and runs. It hasn't changed at all. [SNIP] While I know that it comes from Google and I don't question the tarball from a security point of view, portage still complains about it each time and deletes it for me, since it thinks it is a security problem. That would normally be a great idea but then I have to download it again, which takes a little over two hours for me. I get about 10Mbs a hour here. [SNIP] I can't help wondering. If you don't have the bandwidth to upgrade when there is an upgrade. How useful is googleearth to you then. It's not like it doesn't require any bandwidth just to run... Also the more often you sync the more bandwidth you need with Gentoo in general.. I only got it once. :/ Well, I tried the other way around, not updating as often but I have it all planned out now. The problem with waiting is that it builds up. I would hate to sync after a month or so then find out OOo and KDE was updated, plus some otehrs for good measure. Just OOo takes me about 24 hours to download. Yes, I get the compiled version. This is Gentoo after all. ;-) Plus, I ran into a config nightmare. To many updates at once for me. I'm not a guru. The way I do is this, I connect around 10:00PM, check my emails and sometimes the weather. Then I start the sync process and tell it to fetch the new stuff afterwards, got to love the . While it is doing that, I go for my nightly soak in the tub. I have a skin disorder and I have spent several hours in the tub. This works well because at the very least the fetch has started and sometimes it has been fetching for a while. It depends on how many things are updated and how long I soak. As for googleearth, well, dial-up has taught me patience. It works, it just takes a really long time to get there. Sometimes another soak in the tub. LOL Dale :-) :-) :-) -- www.myspace.com/dalek1967
