It's the darndest thing - but I'll take it!
I don't have the diodes. I don't have SSB, or a mic jack. So...I did the
test with the shorted stereo plug. Everything worked fine.
So then, I plugged in my paddles, and - everything worked fine.
Hooked up my new delta loop, worked France with 5W, got
Hi Bill,
For all practical purposes the choice will make no difference to the audio
quality. Either option will certainly be vastly better than picking up the
K3 audio with a microphone. The USB option is just a bit more convenient
since you can can combine audio and rig control in one cable.
I'm trying to mix my K3s sidetone audio with Skypes audio out by using a
software mixer called VoiceMeeter. This will eliminate the mic on my Skype
camera trying to pickup the audio coming from the K3's speaker and hopefully
eliminate most of the audio artifacts. Does it matter where I pick off
For Sale. For K3 non "S."
Elecraft PR6 6m preamp. Includes dual BNC connectors, power cord with RCA plug,
DB15 to K3 AUX connector, original manual.
$110 shipped USPS. USA only.
Elecraft KXV3A. Upgraded KXV3. Allows connection of an RX antenna and interface
for a PR6 6m preamp. This is NOT
I use a 3 by 5 card which just fits under the Pod.
I draw a grid of 4 squares with ink on each side that sticks out from under the
Pod and pencil in the commands.
Chuck
KE9UW
Sent from my iPhone, cjack
> On Aug 28, 2018, at 4:34 PM, VE3WDM wrote:
>
> I have used the P-touch labels but stick
Now that is very intriguing to me, Mike. Do you have a simple source for the
magnetic tape that works for you?
73,
Bill
K9YEQ
https://wrj-tech.com/
-Original Message-
From: elecraft-boun...@mailman.qth.net On
Behalf Of VE3WDM
Sent: Tuesday, August 28, 2018 4:34 PM
To:
I have used the P-touch labels but stick them on a pre-cut magnetic strip
this way you can have add or remove them from the K-pod. The labels are held
in place by the magnet. This way you can have a set for contesting, QSO and
DXpeditions.
Don is your best source but ... any chance it got set to Iambic B and
you're an Iambic A guy? Iambic B adds elements that you don't actually
send. Just a thought.
73,
Fred ["Skip"] K6DGW
Sparks NV DM09dn
Washoe County
"Never iambicized"
On 8/28/2018 1:08 PM, LL wrote:
This is the
I have a nice K1 for sale. If interested, drop me an email for details.
Carl Yaffey K8NU
Recording studio.
cyaffeyno_s...@gmail.com
614 268 6353, Columbus OH
http://www.carl-yaffey.com
http://www.grassahol.com
http://www.bluesswing.com
At the risk of stating the obvious, check your key cable & plug. Sounds
like it is intermittently shorting producing longer dahs & extra dits.
73,
Drew
AF2Z
On 08/28/18 16:08, LL wrote:
This is the weirdest thing ever.
So my wonderful K2, #4442, was pressed into service once again, a few
Lloyd,
Do you have the 2 diodes to permit using a hand key in addition to
paddles (auto-detect)?
If so, try removing the diodes to see if it works - Turn off auto-detect.
Do you have a microphone connected? If so, remove it on the possibility
that there may be a mic problem with the PTT
The only time I can make signals pop out is when I put in enough ATT to make
noises floor S0. Then it is like a FM channel when signal come in. BUT the
incoming signal needs to be several S units above the quiet noise floor to
truly open the gate so to speak. Weak signals near the noise
I've been at this for 60 years now and the only time I've ever heard signals
"pop out of the noise" was when I was working 2-meter meteor scatter. Where
have I gone wrong?
Wes N7WS
On 8/27/2018 8:02 PM, Don Wilhelm wrote:
When you can just barely hear the no-signal band noise, signals will
This is the weirdest thing ever.
So my wonderful K2, #4442, was pressed into service once again, a few
months ago, after some needed TLC from Alan Wilcox.
All was fine. In fact, it was all wonderful!
So I just built a new antenna; got it up yesterday, it's a 40M full-wave
Delta Loop. Hoping
Though that would probably work, I think it's very confusing and
counter-intuitive to program an Elecraft amplifier to use an Icom protocol
to communicate with a Yaesu transceiver by relying on a microHAM microKEYER
to translate the Yaesu CAT commands to equivalent ICOM CI-V commands.
Note that
I made my labels on my P-Touch label machine [identical to the Brother
machine] that prints on white adhesive tape. Each button is an
individual piece of tape. At the smallest font, there's room for
2-lines of 3 characters, top is TAP, bottom is HOLD. KPOD has really
changed the way I
The S-Box is completely unnecessary ...
Configure the KPA-1500 to work with an *ICOM* transceiver (CI-V data)
and configure MK II to output CI-V data on the *AUX CI-V* jack (rear
panel). The concept is identical to use of an Icom PW1 amplifier
with MK II as described in the application note
I am posting this as an update and recommendation on how I got all my
electronics playing correctly together. I recently bought a new Elecraft
KPA1500 amplifier and wanted it to work seamlessly with my FTdx5000 and
microHam Keyer 2. Just not enough serial ports to go around; thought I
could
Fellow Elecrafters,
Is there anyone on the list living in VR2 ? If so could you
contact me off-list please.
Thanks
Tim, Sheung Wan. Hk.
__
Elecraft mailing list
Home:
Has anyone on the list been successful in remoting their KPA1500 over the
Internet using either USB or Ethernet server mode? I've tried both modes,
and no-go. Just getting either host server mode up and active at the remote
site takes perhaps ten tries to finally connect. However, to date I've
I used the adhesive backed 12mm wide tape from an old Brother P-Touch on
small print which is about 1/8 of an inch. I then cut them down to about
3/16 width by 2-1/2" long. I put one on each side of each row of F keys.
It's the same tape I use for labeling all the cables in the shack.
73
Somebody has well solved the problem of labeling clearly the F-Keys on the
K-POD?
How?
I am interested to use a clean and clear way of labelling the K-Pod
commands.
Thanks.
Ian - IK4EWX
--
Sent from: http://elecraft.365791.n2.nabble.com/
22 matches
Mail list logo
