Thanks Joe, I have already located a set.
BillB
In a message dated 9/10/2008 11:33:39 P.M. Central Daylight Time,
[EMAIL PROTECTED] writes:
Bill,
Do you need the sender or the sponder, or both? I think there may be a
set in our collection. Let me know what you need and I will take a
I'm working on a few projects and need a number of N female flange
mount style connectors, crimp style for RG58/142/400u cable. Similar
to those found on the side of MSF5000 cabinets. Amphenol part # 082-
5372. Anyone have any?
Have any of you folks recently needed to refresh your shop stock
Has anyone controlled the encode function of a TS32P via a CAT
controller's encode logic pin?
I've wired several SCOM 7330s and Arcom RC210s to factory encoders in
MS2000s, Micors, and even outboard TS32 encoders. The Scom and Arcom
controllers can be configured to set their encode logic for
Be careful. The crimp ferrule for double-shielded coax (RG142/400) is thinner
than what it would be for single-shielded coax (RG58) to allow more braid to
fit under it, yet still use the same crimping tool. Many vendors don't know the
difference, and you'll have a heck of a time pushing/forcing
Add a simple NPN transistor (and two resistor) inverter between the CAT and the
TS32. Don't fight it, just put on your Borg hat and adapt.
Of course you know that the CAT only enables its transmit PL when there's a
valid COR signal on the input. You won't get PL activated on CW ID, courtesy
Thanks for the tip on the ferrules. I've run into that situation a
few times, but have usually been able to make them work when needed.
Who is hdcom? Never heard of them... I'll try to find them on the
web.
Thanks
Eric
--- In Repeater-Builder@yahoogroups.com, Bob M. [EMAIL PROTECTED]
Thanks, Bob.
The NPN was my plan if no one had any better suggestion. All I'll
need to do is tie the CAT's logic pin to a 10K pullup and 2n,
then tie the collector to the TS32P's op amp input, and the emitter
to ground.
At least the CAT will enable the encoder based on rx activity of
Yup, that's all I'd do for an inverter.
I have two repeaters using CAT200Bs and have had no problem with the audio. I
never measured it to see how flat it was. It's not broadcast quality; it's not
supposed to be.
hdcom sells coax connectors, cables, etc. They're located on Lawn Guy Land.
Bob
(20080911) Information __
This message was checked by NOD32 antivirus system.
http://www.eset.com
I received the below email from [EMAIL PROTECTED] what does it mean and
what happened?
Since the Repeater-Builder yahoo group has been shut down with no
word of if or when it will be operational, I have started a new yahoo
group called building-repeaters . The idea of this group is for
Does anyone know where I can find three (retired or inexpensive) 900
Mhz radios that I can use as link radios? I will need only low power
radios because of the short disatance..about 8 miles between the sites
and the control point. Thanks for any help!
C
Thanks for all the Opinions on the EF line!
How about the DRB-25 series Icom Mixed Mode Stuff? Good, Bad, Indifferent?
As long as were at it, I'll pose this question: Your mission- Spend grant money
on a brand new repeater with the requirement it needs to support P25 but
operate mixed mode.
On Sep 10, 2008, at 4:30 PM, Paul Plack wrote:
Perhaps someone of your obvious intellect and condescension can tell
me why
some messages won't let me delete extraneous text from the original
after I
start the reply. (Yes, I'm using Outlook Express...I'm not going to
use a
browser to
At 03:23 PM 09/11/08, you wrote:
I also don't care for the audio quality thru the CAT controllers.
Somewhat restricted curve as compared to the others. I would never
use a CAT on my own repeaters, but this is for someone else, so I'm
using what they had on hand.
This is a prime case of you get
.
This is a prime case of you get what you pay for, and where the
extra money spent for an SCOM or Link is money well spent.
Eric
KE2D
Dunno if this is relevant, but
http://www.repeater-builder.com/cat-auto/cat-1000-audio.html
Mike WA6ILQ
__ NOD32 3436 (20080911) Information
controller and the
TS32, does anyone else have any ideas?
Eric
KE2D
__ NOD32 3435 (20080911) Information __
This message was checked by NOD32 antivirus system.
http://www.eset.com
as well.
Before I add some inverting logic between the CAT
controller and the
TS32, does anyone else have any ideas?
Eric
KE2D
__ NOD32 3435 (20080911) Information __
This message was checked by NOD32 antivirus system.
http://www.eset.com
On Sep 11, 2008, at 9:15 PM, TGundo 2003 wrote:
As long as were at it, I'll pose this question: Your mission- Spend
grant money on a brand new repeater with the requirement it needs to
support P25 but operate mixed mode. What would you use?
Quantar seems to do pretty well for those I've
We are still looking for someone to build and distribute my Repeater
interface Module, and cross band Module. The Repeater Module has a
excellent track record in public safety and commercial LMR.
I am looking for someone who wants to take over the two products.
Contact me directly,
Will
Yahoo has lately been letting HTML mail through,
and OE might be displaying some of the message
as HTML/graphics or similar? It's really hard to tell
from here. But it's really odd that it won't let you
remove the text. Hmm.
Interestinger still, the message quoted above would not let me
20 matches
Mail list logo
