Oooh good call, didn't see that. I just Google'd Cambium RMA.
Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373 On Fri, Aug 7, 2015 at 12:46 PM, Ken Hohhof <[email protected]> wrote: > Hmmmm, I see you can replace “ptp” with “epmp” in the URL and that works, > but “pmp” does not. > > > *From:* Josh Luthman <[email protected]> > *Sent:* Friday, August 07, 2015 11:37 AM > *To:* [email protected] > *Subject:* Re: [AFMUG] RF Calibration Failure ADI Catalina R1 chip > notsupported! > > This may or may not actually work. I filled this out early this week and > haven't heard back: > > http://www.cambiumnetworks.com/support/ptp/rma-request > > > Josh Luthman > Office: 937-552-2340 > Direct: 937-552-2343 > 1100 Wayne St > Suite 1337 > Troy, OH 45373 > > On Fri, Aug 7, 2015 at 12:35 PM, Ken Hohhof <[email protected]> wrote: > >> I had one sitting here from the field that developed intermittent ADI >> communication failures. Just sent an email to [email protected]. >> Not sure if that’s the right way, or if you’re supposed to open a ticket. >> >> *From:* George Skorup <[email protected]> >> *Sent:* Friday, August 07, 2015 11:26 AM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] RF Calibration Failure ADI Catalina R1 chip not >> supported! >> >> Hey, if they need failed hardware to figure it out, fine with me. >> >> On 8/7/2015 6:45 AM, Mike Hammett wrote: >> >> In my experience, if you complain a lot and offer to drive it to them, >> they take you up on it. ;-) >> >> >> >> ----- >> Mike Hammett >> Intelligent Computing Solutions >> http://www.ics-il.com >> >> ------------------------------ >> *From: *"George Skorup" mailto:[email protected] <[email protected]> >> *To: *[email protected] >> *Sent: *Friday, August 7, 2015 1:03:18 AM >> *Subject: *Re: [AFMUG] RF Calibration Failure ADI Catalina R1 chip not >> supported! >> >> I have two on my desk that I submitted support case requests for and >> haven't got a response yet. You want me to drive them up to Rolling >> Meadows? :) >> >> The 5GHz SM shows RF calibration failure and ADI communication failure. >> The 3GHz SM shows only RF calibration failure. They both reboot shortly >> after starting to scan. I think I might have another 5GHz in my WTF pile >> too, have to check tomorrow. >> >> On 8/6/2015 11:37 PM, Rajesh Vijayakumar wrote: >> >> We are waiting for the RMA'd units to reach us, so we can look at what is >> going on. I am told we should get at least one unit on Monday. I will >> provide more details as soon as possible. I am sorry about the trouble this >> is causing. >> Rajesh Vijayakumar >> Cambium Networks >> >> On Thu, Aug 6, 2015 at 1:14 PM, Brian Sullivan <[email protected] >> > wrote: >> >>> We have had a few. >>> >>> >>> On 8/6/2015 12:12 PM, timothy steele wrote: >>> >>> yeah same here 1 was a tower climb.. was hoping someone knew whats >>> making this happen as they work fine out of the box then die later >>> >>> On Thu, Aug 6, 2015 at 12:16 PM, George Skorup <[email protected]> >>> wrote: >>> >>>> Had a couple 3GHz and 5GHz SMs last week as well. Replace and RMA is >>>> the only solution. >>>> >>>> >>>> On 8/6/2015 11:11 AM, timothy steele wrote: >>>> >>>> we have had 2 brand new 5ghz 450's out of the blue have the RF die and >>>> show in re letters >>>> >>>> RF Calibration Failure >>>> ADI Catalina R1 chip not supported! >>>> >>>> They both where running 13.2.1 and both where installed for a week or >>>> so before they stopped running tired defaulting both and upgrading firmware >>>> on both did not work they also randomly reboot the 2 where installed a 2hr >>>> drive apart connected to diffrent towers >>>> >>>> >>>> anyone have any clue whats going on here?? >>>> >>>> >>>> Thanks >>>> >>>> >>>> >>>> >>>> >>>> >>> >>> >>> >> >> >> >> >> >> >
