I just tried the "debouncepowerport off" command and no change. I may try downgrading to firmware 14.1.2.
On Thu, Nov 24, 2016 at 10:06 PM, Chuck McCown <[email protected]> wrote: > OK, I did get a report from one customer that my new surge protector > design actually fixed this problem with a 450i. > Not yet confident enough to state it will fix the problem. > > I was testing with my new surge suppressor when I got it to go. > > *From:* Forrest Christian (List Account) > *Sent:* Thursday, November 24, 2016 4:31 PM > *To:* af > *Subject:* Re: [AFMUG] Gigabit power injector + sync > > The 450i is extremely sensitive to any transition noise on the pulse. > There's a hidden command in the cambium radios which you may want to try. > I'm sending you a email off-list with it in caseyou want to try it. > > > On Thu, Nov 24, 2016 at 3:14 PM, Kurt Fankhauser <[email protected] > > wrote: > >> Ok, I just put a new PMP450i on a tower and am running into the exact >> same problem the Original Poster had here. I have the Gigabit Power >> Injector plus Sync and it is blinking for receiving sync from another Sync >> Injector in the same enclosure via the included jumper cable and the AP is >> running in Autosync+ Freerun and it is not showing receiving any sync at >> all and it is decided to Generate its own Sync. Has been running for a >> couple hours now. Will keep checking back here. >> >> On Tue, Nov 22, 2016 at 1:51 PM, That One Guy /sarcasm < >> [email protected]> wrote: >> >>> all this talk of the new units i opened our box of them, is there a >>> guide for the 10/100 and gigabit powerinjector jumper settings per brand? >>> is it just the same as http://tickets.packetflux.com/ >>> downloads/poeinjectorjumpers.pdf only with the pin order backward? >>> and if a guy put a 3pin connector on the A/B selector, would that >>> effectively put the two inputs in parallel? >>> >>> On Tue, Nov 22, 2016 at 11:57 AM, Forrest Christian (List Account) < >>> [email protected]> wrote: >>> >>>> Depends on the power circuitry on the airfiber. My guess is it would >>>> be ok. >>>> >>>> If you have a base unit, you can actually turn off the sync on that >>>> port and the injector will remember it, so you don't have to put a base >>>> unit in the field with it, just for the programming. (You'd set the >>>> poweron column for the sync row for that port to '0'). >>>> >>>> On Tue, Nov 22, 2016 at 8:37 AM, Kurt Fankhauser < >>>> [email protected]> wrote: >>>> >>>>> I just received my first powerinjector + sync today. If I want to >>>>> power some Airfibers with these do I need to turn the sync off for those >>>>> ports? I don't see a jumper to turn off sync, is it ok to provider sync on >>>>> a port with an Airfiber? Does it hurt anything? It looks to me like the >>>>> only way to turn off sync is buy the additional site monitor base thing to >>>>> hookup to it and turn it off through the web interface? >>>>> >>>>> On Mon, Nov 21, 2016 at 2:39 PM, George Skorup <[email protected]> >>>>> wrote: >>>>> >>>>>> I have four 5GHz 450i's running on our office tower fed from a GigE >>>>>> PowerInjector+Sync. They're running 14.1.2. They received sync shortly >>>>>> after boot, DFS, etc. BTW, no GigE-APC's in line on these yet. I'm like >>>>>> two >>>>>> short at the moment. But we know that 1000Base-T and sync over power + >>>>>> the >>>>>> older APC's don't play nice anyway. >>>>>> >>>>>> On 11/21/2016 1:23 PM, Mathew Howard wrote: >>>>>> >>>>>> I've had a couple of them where I wasn't getting sync and couldn't >>>>>> figure out why... in one case (maybe both... I don't remember off hand), >>>>>> I >>>>>> was getting sync to an ePMP, but not to a PMP450i 900mhz AP that were >>>>>> both >>>>>> plugged into the same sync injector... I didn't really need sync on the >>>>>> 900mhz at the time, so I just switched it to generate it's own timing, >>>>>> and >>>>>> I haven't gotten around to trying to figure it out yet, but now I'm >>>>>> wondering if it would eventually come up if I left it alone. >>>>>> >>>>>> On Mon, Nov 21, 2016 at 12:45 PM, Seth Mattinen <[email protected]> >>>>>> wrote: >>>>>> >>>>>>> On 11/21/16 10:39, [email protected] wrote: >>>>>>> >>>>>>>> I had all the packet flux gear running for days, plugged in the >>>>>>>> 450i and >>>>>>>> started trying to figure out why it was not receiving sync. Half >>>>>>>> hour >>>>>>>> or more later it said it was OK, so the delay had to be Cambium, not >>>>>>>> Packetflux. >>>>>>>> >>>>>>> >>>>>>> >>>>>>> Check if the packetflux says it has fix and 1PPS is active on the >>>>>>> binary tab and that the used pulse count is increasing on the analog >>>>>>> tab. >>>>>>> >>>>>>> ~Seth >>>>>>> >>>>>> >>>>>> >>>>>> >>>>>> >>>>> >>>> >>>> >>>> >>>> -- >>>> *Forrest Christian* *CEO**, PacketFlux Technologies, Inc.* >>>> Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 >>>> [email protected] | http://www.packetflux.com >>>> <http://www.linkedin.com/in/fwchristian> >>>> <http://facebook.com/packetflux> <http://twitter.com/@packetflux> >>>> >>>> >>> >>> >>> -- >>> If you only see yourself as part of the team but you don't see your team >>> as part of yourself you have already failed as part of the team. >>> >> >> > > > > -- > *Forrest Christian* *CEO**, PacketFlux Technologies, Inc.* > Tel: 406-449-3345 | Address: 3577 Countryside Road, Helena, MT 59602 > [email protected] | http://www.packetflux.com > <http://www.linkedin.com/in/fwchristian> <http://facebook.com/packetflux> > <http://twitter.com/@packetflux> > >
