One vote for Force180 Josh Luthman Office: 937-552-2340 Direct: 937-552-2343 1100 Wayne St Suite 1337 Troy, OH 45373
On May 23, 2017 8:21 AM, "Faisal Imtiaz" <[email protected]> wrote: > FWIW...... the situation described is the exact scenario for a Micro-POP. > > There are a number of folks who are currently doing such a setup with > 60ghz or 24ghz as backhaul and Mimosa A5's for 5ghz PTMP... expected > thruput is between 150meg to 300meg easily. > > Regards. > > Faisal Imtiaz > Snappy Internet & Telecom > 7266 SW 48 Street > Miami, FL 33155 > Tel: 305 663 5518 x 232 <(305)%20663-5518> > > Help-desk: (305)663-5518 <(305)%20663-5518> Option 2 or Email: > [email protected] > > ------------------------------ > > *From: *"Harold Bledsoe" <[email protected]> > *To: *[email protected] > *Sent: *Tuesday, May 23, 2017 6:26:37 AM > *Subject: *Re: [AFMUG] extending fiber with RF > > How about 60ghz to the first house and 5ghz to the second house and run > Trill to create a ring? > > Does using multiple new technologies instead of just one make it seem less > risky? š > > Hal > > On Mon, May 22, 2017 at 3:47 PM Chuck McCown <[email protected]> wrote: > >> Scared of new technology. >> Seems a bit too long range for that freq. >> Worried about not enough time has elapsed to prove them out. >> They sound expensive. >> Everybody knows 60 GHz is all absorbed by the oxygen anyhow... >> Not sure God would approve... >> >> You all the same normal reasons... >> >> *From:* Brett A Mansfield >> *Sent:* Monday, May 22, 2017 1:44 PM >> *To:* [email protected] >> *Subject:* Re: [AFMUG] extending fiber with RF >> For so little throughput a 5GHz setup would be the cheapest and probably >> best setup. >> >> What keeps you from being a believer of the 60GHz? I can show you the >> history of some of my Ignitenet links that may just change your mind. >> >> Thank you, >> Brett A Mansfield >> >> On May 22, 2017, at 12:38 PM, Chuck McCown <[email protected]> wrote: >> >> Not a believer yet. And we only need 100-250 Mbps max to the homes. >> Actually probably more like 50 or 100 Mbps. >> Want it to be simple too. ONT has multiple ethernet ports on it. Just >> extend those physical layer 0/1 connections. >> >> >> *From:* Cameron Crum >> *Sent:* Monday, May 22, 2017 1:34 PM >> *To:* [email protected] >> >> *Subject:* Re: [AFMUG] extending fiber with RF >> >> What about a couple of 60GHz links with a single 5GHz AP as a backup? We >> did this for a bank that needed to connect two buildings temporarily. Put a >> MT on either side that ran IPSEC tunnel over the link with a failover >> script to route traffic over the 5 GHz link if the 60 lost more than 50% of >> it's packets. The 5 GHz was slower, but they still had connectivity in the >> even of a heavy rain. >> >> On Mon, May 22, 2017 at 2:28 PM, Chuck McCown <[email protected]> wrote: >> >>> Still puzzling over how to get ethernet the last 3000 feet. I have >>> fiber to a point along a rural road. The end is about 2000 feet from one >>> home and 3000 feet from another. >>> >>> Was looking at using the existing copper with VDSL line extenders. That >>> was what that week of math problems was all about. I am starting to lean >>> away from that solution because it is old copper. I really want to stop >>> using it. >>> >>> I donāt have a ROW that is legal. The old copper technically is in >>> trespass and the owner of the property is known to be a major PITA. So not >>> sure if I can get permission. Even then, we are talking about 5000 feet of >>> fiber to place. There will be some money involved. >>> >>> Using wireless could be much cheaper. Will have to do a solar install >>> with the ONT and RF gear on a stub pole at the handhole. >>> >>> Not sure what kid of RF. Donāt want to use an AP because I need two >>> layer 2 connections from the ONT. Be more expensive to use an AP anyhow. >>> So two PTP systems. Rock solid, never fail type of system. Noise floor >>> down there is probably pretty low. >>> I could use a pair of rockets etc. Not wanting to lo-ball this, want it >>> to be very solid. >>> >>> What would you use? >>> >> >> >> -- > > Harold Bledsoe > >
