A basic would work, along with about anything other than an aux or timing port version
On Jun 15, 2017 11:01 AM, "Paul McCall" <pa...@pdmnet.net> wrote: > We had moved away from SyncPipes for the most part, bought the SPJ Basics > instead of pipes the past few times we needed that. > > > > *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *George Skorup > *Sent:* Thursday, June 15, 2017 11:37 AM > *To:* af@afmug.com > *Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS type > device > > > > What else you got laying around? Deluxe pipe? Rev F/G/H will work fine > with 12-56VDC. > > On 6/15/2017 10:34 AM, Paul McCall wrote: > > That’s what it appears. Am wondering if Forrest has a different voltage > range for input since he built it himself > > > > Paul > > > > *From:* Af [mailto:af-boun...@afmug.com <af-boun...@afmug.com>] *On > Behalf Of *George Skorup > *Sent:* Thursday, June 15, 2017 11:29 AM > *To:* af@afmug.com > *Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS type > device > > > > I'm about 63.48% sure that UGPS power is like 5-7VDC which is on one of > the serial lines, IIRC. > > On 6/15/2017 10:15 AM, Paul McCall wrote: > > Soooo… can I power it off an S16 somehow, with the right cable? (24v?) > > > > Paul > > > > *From:* Af [mailto:af-boun...@afmug.com <af-boun...@afmug.com>] *On > Behalf Of *Forrest Christian (List Account) > *Sent:* Thursday, June 15, 2017 11:04 AM > *To:* af <af@afmug.com> <af@afmug.com> > *Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS type > device > > > > OK found a short .pdf manual. Looks like the 100 series may not support > this. > > The timing port model needs ugps power. > > > > On Jun 15, 2017 9:46 AM, "Forrest Christian (List Account)" < > li...@packetflux.com> wrote: > > Hmm. ... odd. I know it's in the 450, but I thought it was in the older > radios too. > > > > I'm traveling, so can't look it up, but what does the uGPS manual say > about FSK radios? > > > > On Jun 15, 2017 9:42 AM, "George Skorup" <george.sko...@cbcast.com> wrote: > > I don't have a single P10 or P11 FSK AP that has UGPS power control on the > config page. Perhaps it's just always on? > > On 6/15/2017 9:35 AM, Forrest Christian (List Account) wrote: > > AFAIK All semi-modern fsk radios provide uGPS power. Just connect the > radio and box together and turn on uGPS power in the radio. Use whatever > cable cambium recommends for a uGPS probably just a 6p6c straight through > cable, although it might make sense to skip the factory reset pin. > > > > > > > > On Jun 15, 2017 9:19 AM, "Paul McCall" <pa...@pdmnet.net> wrote: > > Hmmmm….. let me try again. > > > > I have a single FSK AP that is getting powered/ethernet successfully > connected to a UBNT S16. I need to get sync to that radio. I want to > power the SB Junior Timing Port Version by making a cable that I can > connect to the S16 that will connect to one of the SBJTP timing ports to > power it up. > > > > Unless that ALL FSKs timing ports actually would provide the power needed > to power up the SBJTV ? with a “standard” cable whatever that means 😊 > > > > Paul > > > > *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Forrest Christian > (List Account) > *Sent:* Thursday, June 15, 2017 10:08 AM > *To:* af <af@afmug.com> > *Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS type > device > > > > What type of fsk radio do you gave that doesn't do ups power? > > > > On Jun 15, 2017 9:04 AM, "Paul McCall" <pa...@pdmnet.net> wrote: > > Syncbox Junior Timing Port Version > > > > *From:* Af [mailto:af-boun...@afmug.com] *On Behalf Of *Forrest Christian > (List Account) > *Sent:* Thursday, June 15, 2017 10:03 AM > *To:* af <af@afmug.com> > *Subject:* Re: [AFMUG] Powering a Syncbox Junior without a uGPS type > device > > > > Which syncbox? > > > > On Jun 15, 2017 8:51 AM, "Paul McCall" <pa...@pdmnet.net> wrote: > > Guys, > > > > We need to providing timing on a single FSK AP and it is fed up the tower > through fiber to a UBNT S16. (so its powering off the S16). I want to use > one timing port to output timing to the FSK (as normal) and one port to > receive power from the S16 and need to figure out the pinout (wiring > diagram) to make that happen. > > > > Paul > > > > Paul McCall, President > > PDMNet, Inc. / Florida Broadband, Inc. > > 658 Old Dixie Highway > > Vero Beach, FL 32962 > > 772-564-6800 <%28772%29%20564-6800> > > pa...@pdmnet.net > > www.pdmnet.com > > www.floridabroadband.com > > > > > > > > > > >
