MT using OSPF is the proper method, LACP does not take into account loading, its jus a LAG group, and it will be 1:1. That’s it. OSPF you can acutallly load balance 3:1 or 6:1 etc, but the more connections the better the load balance. But that is the number of connections, not actual load but again, if you have lots of connections then it will balance out. Plus failover is simpler as well (at least in my eyes)
Dennis Burgess – Network Solution Engineer – Consultant MikroTik Certified Trainer/Consultant<http://www.linktechs.net/productcart/pc/viewcontent.asp?idpage=5> – MTCNA, MTCRE, MTCWE, MTCTCE, MTCINE For Wireless Hardware/Routers visit www.linktechs.net<http://www.linktechs.net/> Radio Frequency Coverages: www.towercoverage.com<http://www.towercoverage.com/> Office: 314-735-0270 E-Mail: [email protected]<mailto:[email protected]> From: Af [mailto:[email protected]] On Behalf Of Mathew Howard Sent: Monday, January 15, 2018 2:01 PM To: af <[email protected]> Subject: Re: [AFMUG] LACP or what for non symetric throughput It looks like Mikrotik supports several different types of bonding, some of which appear to support asymmetrical links. I just started looking into this stuff myself, so I really don't know what I'm talking about... I'm currently just using OSPF to load balance a couple of links, and I'm trying to figure out if there's a better way we should be doing it. On Mon, Jan 15, 2018 at 1:46 PM, Steve Jones <[email protected]<mailto:[email protected]>> wrote: so what options do I have here/ we are currently bench testing lacp in HP switches to get moving, but need a longer term better solution On Fri, Jan 12, 2018 at 6:38 PM, Steve Jones <[email protected]<mailto:[email protected]>> wrote: im not being argumentative btw, im outside my scope, just showing my data sources. I honestly dont know what to do here. If a contractor here wants to offer some services, i have that budget as well. Im not certain our usual contractor will give me what i need... and butch doesnt answer my emails On Fri, Jan 12, 2018 at 5:01 PM, Steve Jones <[email protected]<mailto:[email protected]>> wrote: https://forum.mikrotik.com/viewtopic.php?t=110400 If Im reading the mikrotik guy (MRZ) response correctly. mikrotik will balance a single stream across multiple ports I put my comprehension at a 10% reliability, so.... On Fri, Jan 12, 2018 at 4:17 PM, Josh Baird <[email protected]<mailto:[email protected]>> wrote: You will have the same limitation using LACP. On Jan 12, 2018, at 5:00 PM, Steve Jones <[email protected]<mailto:[email protected]>> wrote: that will limit single stream to single port speed, will it not? So I would end up saturating one link while not using the other if a single stream were to get heavy? On Fri, Jan 12, 2018 at 3:50 PM, Eric Kuhnke <[email protected]<mailto:[email protected]>> wrote: Don't try to do it at L2. Build it as router-to-router OSPF+BGP adjacency across the two separate Integra links. Build it as two OSPF /30 links and use OSPF cost to adjust traffic accordingly. On Fri, Jan 12, 2018 at 1:48 PM, Steve Jones <[email protected]<mailto:[email protected]>> wrote: So we will be doing this integra 2+0 link. We got dinged by sprint though on the PCN. so we have to drop one sides power on one channel since this path has no other channels. This drops that one chain to 256qam (for reliability) from 1024 so 643-514mbps. This model 2+0 the radios dont communicate so its really just 2 separate links handled externally so I go from (643+643) / (643+643) to (514+643) / (643+643) Is there any way with LACP to account for this single path that will be lower than the other two? There is nothing that fully ties me to LACP. I have the option of HP procurve switches or Mikrotik CCR routers to handle the aggregation. As best I can tell LACP doesnt have any granular throughput definition, just splits traffic across all interfaces (last i read, routeros and the hp OS both allow full aggregate speed instead of single streams being limited to individual port throughput) In my case with 1.2gbps i still have an 800mbpsish overflow issue. so If there is an aggregation thats semi dynamic and granular to actual link capacity, that would tickle my goat any advice from the sages? Id like to keep my switch/routers solution to under 1k per side, much less if possible. I already have HP 1810g-24 that i believe will handle this, so theyre effectively free
