When i print the bootargs it is printing correctly.. But when i am trying ti seteenv bootargs i am getting the following error..
OMAP3 beagleboard.org # setenv bootcmd mmcinit;fatload mmc 0 0x80300000 uImage;bootm 0x80300000 ** Unable to use mmc 0:1 for fatload ** Wrong Image Format for bootm command ERROR: can't get kernel image! Why is this so? On Fri, Sep 25, 2009 at 2:32 PM, Kaushik(ICMAN) <[email protected]>wrote: > Can you make sure that you followed ...the steps mentioned in the link > below. I believe that your bootargs are wrong. > > http://kaushikprajapati.wordpress.com/2009/09/20/33/ > <http://kaushikprajapati.wordpress.com/2009/09/20/33/> > > On Fri, Sep 25, 2009 at 1:56 AM, sanyanniesunney anniesunney < > [email protected]> wrote: > >> Yes i am using the beagle board.. >> and i am also booting from the SD card! >> >> what should i do.... >> >> On Fri, Sep 25, 2009 at 2:09 PM, Kaushik(ICMAN) < >> [email protected]> wrote: >> >>> I believe the address is wrong. Are you using beagleboard?? and >>> booting from SD card?? >>> >>> >>> On Fri, Sep 25, 2009 at 1:23 AM, sanyanniesunney anniesunney < >>> [email protected]> wrote: >>> >>>> Hi, >>>> >>>> I have already done this and my o/p at the minicom terminal was like >>>> this, >>>> >>>> Texas Instruments X-Loader 1.41 >>>> Starting OS Bootloader... >>>> >>>> >>>> U-Boot 2008.10-rc2 (Oct 2 2008 - 09:02:46) >>>> >>>> OMAP3530-GP rev 2, CPU-OPP2 L3-165MHz >>>> OMAP3 Beagle board + LPDDR/NAND >>>> DRAM: 128 MB >>>> NAND: 256 MiB >>>> In: serial >>>> Out: serial >>>> Err: serial >>>> Hit any key to stop autoboot: 0 >>>> reading uImage >>>> >>>> 1820016 bytes read >>>> ## Booting kernel from Legacy Image at 80300000 ... >>>> Image Name: Linux-2.6.29-omap1 >>>> Image Type: ARM Linux Kernel Image (uncompressed) >>>> Data Size: 1819952 Bytes = 1.7 MB >>>> Load Address: 00008000 >>>> Entry Point: 00008000 >>>> Verifying Checksum ... OK >>>> Loading Kernel Image ... >>>> It get stuck at this point! >>>> Now i dunno how to proceed! >>>> >>>> On Fri, Sep 25, 2009 at 12:59 PM, Kaushik(ICMAN) < >>>> [email protected]> wrote: >>>> >>>>> Enabling Network >>>>> >>>>> - Connect eth0 interface to usb hub via ethernet to usb converter >>>>> - Edit init.rc from <Android_RFS>/init.rc >>>>> >>>>> #basic network init >>>>> setprop net.dns1 <primary-dns-server-ip> >>>>> >>>>> >>>>> - Boot Beagle board >>>>> - Execute following commands from minicom >>>>> >>>>> $netcfg eth0 up >>>>> $netcfg eth0 dhcp >>>>> >>>>> *NOTE:-* Enable appropriate driver for your "ethernet to usb >>>>> converter" in kernel. Driver can be found at :- >>>>> >>>>> │ -> DeviceDrivers │ │ -> Network device support (NETDEVICES[=y]) │ │ >>>>> -> USB Network Adapters >>>>> >>>>> On Fri, Sep 25, 2009 at 12:29 AM, Kaushik(ICMAN) < >>>>> [email protected]> wrote: >>>>> >>>>>> You can do make menuconfig and try to find out the driver for your >>>>>> device and then create new uImage that will have the USB network Adpater >>>>>> driver. >>>>>> >>>>>> http://kaushikprajapati.wordpress.com/2009/09/25/a-hand-out-on-how-to-do-make-menuconfig-on-android-kernel/ >>>>>> >>>>>> >>>>>> <http://kaushikprajapati.wordpress.com/2009/09/25/a-hand-out-on-how-to-do-make-menuconfig-on-android-kernel/> >>>>>> >>>>>> On Fri, Sep 25, 2009 at 12:26 AM, sanyanniesunney anniesunney < >>>>>> [email protected]> wrote: >>>>>> >>>>>>> I am using USB ethernet adapter,whose one end is connected to the USB >>>>>>> hub and the other end is connected to the ethernet cable..... >>>>>>> >>>>>>> On Fri, Sep 25, 2009 at 12:38 PM, Kaushik(ICMAN) < >>>>>>> [email protected]> wrote: >>>>>>> >>>>>>>> Are you trying to use USB to Ethernet cable or you are trying to use >>>>>>>> USB OTG for Ethenet access? >>>>>>>> >>>>>>>> On Fri, Sep 25, 2009 at 12:05 AM, sany <[email protected]>wrote: >>>>>>>> >>>>>>>>> >>>>>>>>> Hello all, >>>>>>>>> >>>>>>>>> Has anyone been able to enable the ethernet interface on embinux >>>>>>>>> kernel? >>>>>>>>> >>>>>>>>> Plzzzzzz help!!!!!!!! >>>>>>>>> >>>>>>>>> >>>>>>>> >>>>>>>> >>>>>>>> -- >>>>>>>> With Regards, >>>>>>>> Kaushik Prajapati >>>>>>>> Grad. Student >>>>>>>> San Jose State Uni. >>>>>>>> 408-821-5891 >>>>>>>> Pablo >>>>>>>> Picasso<http://www.brainyquote.com/quotes/authors/p/pablo_picasso.html> >>>>>>>> - "Computers are useless. They can only give you answers." >>>>>>>> >>>>>>>> >>>>>> >>>>>> >>>>>> -- >>>>>> With Regards, >>>>>> Kaushik Prajapati >>>>>> Grad. Student >>>>>> San Jose State Uni. >>>>>> 408-821-5891 >>>>>> Samuel >>>>>> Goldwyn<http://www.brainyquote.com/quotes/authors/s/samuel_goldwyn.html> >>>>>> - "I'm willing to admit that I may not always be right, but I am never >>>>>> wrong." >>>>>> >>>>> >>>>> >>>>> >>>>> -- >>>>> With Regards, >>>>> Kaushik Prajapati >>>>> Grad. Student >>>>> San Jose State Uni. >>>>> 408-821-5891 >>>>> Joan >>>>> Crawford<http://www.brainyquote.com/quotes/authors/j/joan_crawford.html> >>>>> - "I, Joan Crawford, I believe in the dollar. Everything I earn, I spend." >>>>> >>>>> >>> >>> >>> -- >>> With Regards, >>> Kaushik Prajapati >>> Grad. Student >>> San Jose State Uni. >>> 408-821-5891 >>> Charles de >>> Gaulle<http://www.brainyquote.com/quotes/authors/c/charles_de_gaulle.html> >>> - "The better I get to know men, the more I find myself loving dogs." >>> >>> > > > -- > With Regards, > Kaushik Prajapati > Grad. Student > San Jose State Uni. > 408-821-5891 > Ted Turner <http://www.brainyquote.com/quotes/authors/t/ted_turner.html> - > "Sports is like a war without the killing." > > > > --~--~---------~--~----~------------~-------~--~----~ unsubscribe: [email protected] website: http://groups.google.com/group/android-porting -~----------~----~----~----~------~----~------~--~---
