its in omap-serial.h in arch/arm/plat-omap/include/plat On Fri, Jul 15, 2011 at 7:58 PM, Manish Shakya <[email protected]>wrote:
> Thanks.Yes, you were right. I tried replacing with O with S. Now I can see > logs in the console. > > Can you tell me where in the source code it says use ttyO instead of ttyS? > I couldn't find in the source. > > Manish > On Fri, Jul 15, 2011 at 11:53 AM, Manish Shakya <[email protected] > > wrote: > >> >> What do you mean? >> >> so now uboot args should look something like this >> console=ttyS2,115200n8 androidboot.console=ttyO2 root=/dev/mmcblk0p2 rw >> rootfstype=ext3 rootwait init=/init vram=12M omapfb.mode=dvi:480x272MR-16@ >> 60 omapdss.def_disp=lcd43 >> >> Is this change in gingerbread 2.3.4 only? >> >> Manish >> >> >> On Fri, Jul 15, 2011 at 11:48 AM, hedwin <[email protected]> wrote: >> >>> in gingerbread ttyS changed to ttyO >>> >>> Hedwin >>> >>> >>> On Fri, Jul 15, 2011 at 5:44 PM, Manish Shakya < >>> [email protected]> wrote: >>> >>>> Right now I am trying to move from linux kernel 2.6.32 to 2.6.37 and use >>>> gingerbread 2.3.4. >>>> >>>> With linux kernel 2.6.32, froyo and gb 2.3.3 are working fine. I used >>>> same uboot arg as in earlier mail. >>>> >>>> On Fri, Jul 15, 2011 at 11:22 AM, hedwin <[email protected]>wrote: >>>> >>>>> Do you use froyo or gingerbread? >>>>> >>>>> >>>>> >>>>> On Fri, Jul 15, 2011 at 3:57 PM, manish shakya <[email protected]>wrote: >>>>> >>>>>> Yes, Both console and android.console is pointing to correct serial >>>>>> device i.e. ttyS2. >>>>>> >>>>>> My uboot args is >>>>>> >>>>>> console=ttyS2,115200n8 androidboot.console=ttyS2 root=/dev/mmcblk0p2 >>>>>> rw rootfstype=ext3 rootwait init=/init vram=12M >>>>>> omapfb.mode=dvi:480x272MR-16@60 omapdss.def_disp=lcd43 >>>>>> >>>>>> Isn't this correct? >>>>>> >>>>>> >>>>>> On Fri, Jul 15, 2011 at 5:44 AM, hedwin <[email protected]> >>>>>> wrote: >>>>>> > >>>>>> > Check if console and android.console point to the correct serial >>>>>> device. >>>>>> > Both a kernel parameters sent by u-boot. >>>>>> > >>>>>> > Cheers, >>>>>> > >>>>>> > Hedwin >>>>>> > >>>>>> > On Thu, Jul 14, 2011 at 9:45 PM, Manish Shakya < >>>>>> [email protected]> wrote: >>>>>> >> >>>>>> >> Hi , >>>>>> >> >>>>>> >> I am wondering what are the changes to be made if I have to make to >>>>>> port rowboat to gumstix overo module. >>>>>> >> >>>>>> >> I did following things but it didn't worked. :-( >>>>>> >> I made change in config file , board-overo.c and also added LCD >>>>>> driver. Compilation went fine with out errors. >>>>>> >> But when I tried to run the image. It show following log and gets >>>>>> stuck. >>>>>> >> >>>>>> >> 2731240 bytes read >>>>>> >> ## Booting kernel from Legacy Image at 82000000 ... >>>>>> >> Image Name: Linux-2.6.37-g06ebbba >>>>>> >> Image Type: ARM Linux Kernel Image (uncompressed) >>>>>> >> Data Size: 2731176 Bytes = 2.6 MiB >>>>>> >> Load Address: 80008000 >>>>>> >> Entry Point: 80008000 >>>>>> >> Verifying Checksum ... OK >>>>>> >> Loading Kernel Image ... OK >>>>>> >> OK >>>>>> >> >>>>>> >> Starting kernel ... >>>>>> >> >>>>>> >> Uncompressing Linux... done, booting the kernel. >>>>>> >> >>>>>> >> >>>>>> >> -- >>>>>> >> Manish Shakya >>>>>> >> http://www.manishshakya.com.np >>>>>> >> >>>>>> >> -- >>>>>> >> unsubscribe: [email protected] >>>>>> >> website: http://groups.google.com/group/android-porting >>>>>> > >>>>>> >>>>>> >>>>>> >>>>>> -- >>>>>> >>>>>> Manish Shakya >>>>>> http://www.manishshakya.com.np >>>>>> http://secs.oakland.edu/~ganesan/iMX/ >>>>>> >>>>> >>>>> >>>> >>>> >>>> -- >>>> Manish Shakya >>>> http://www.manishshakya.com.np >>>> http://secs.oakland.edu/~ganesan/iMX/ >>>> >>> >>> >> >> >> -- >> Manish Shakya >> http://www.manishshakya.com.np >> http://secs.oakland.edu/~ganesan/iMX/ >> > > > > -- > Manish Shakya > http://www.manishshakya.com.np > http://secs.oakland.edu/~ganesan/iMX/ > -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
