Amit, Can you send me link of the thread that notifies all the necessary changes?
Right now, libaudio and surface flinger is crashing. I am planning to use AUDIO stub and increase size of the mem in uboot. I know I am almost there. On Fri, Jul 15, 2011 at 2:41 PM, Amit Pundir <[email protected]> wrote: > Yes I agree that it should have clearly been put in the wiki. > > But I remember that the day Rowboat introduced 2.6.37 kernel branch, a > mail was put on Rowboat mailing list notifying all these necessary > changes. > > Regards, > Amit Pundir > > > On 7/15/11, Manish Shakya <[email protected]> wrote: > > Thanks got it. > > > > I think, this changes should be wrote in rowboat wiki. I wasted 2/3 days. > > > > > > On Fri, Jul 15, 2011 at 2:04 PM, hedwin <[email protected]> wrote: > > > >> its in omap-serial.h in arch/arm/plat-omap/include/plat > >> > >> > >> On Fri, Jul 15, 2011 at 7:58 PM, Manish Shakya > >> <[email protected]>wrote: > >> > >>> Thanks.Yes, you were right. I tried replacing with O with S. Now I can > >>> see logs in the console. > >>> > >>> Can you tell me where in the source code it says use ttyO instead of > >>> ttyS? > >>> I couldn't find in the source. > >>> > >>> Manish > >>> On Fri, Jul 15, 2011 at 11:53 AM, Manish Shakya < > >>> [email protected]> wrote: > >>> > >>>> > >>>> What do you mean? > >>>> > >>>> so now uboot args should look something like this > >>>> console=ttyS2,115200n8 androidboot.console=ttyO2 root=/dev/mmcblk0p2 > rw > >>>> rootfstype=ext3 rootwait init=/init vram=12M > >>>> omapfb.mode=dvi:480x272MR-16@ > >>>> 60 omapdss.def_disp=lcd43 > >>>> > >>>> Is this change in gingerbread 2.3.4 only? > >>>> > >>>> Manish > >>>> > >>>> > >>>> On Fri, Jul 15, 2011 at 11:48 AM, hedwin <[email protected] > >wrote: > >>>> > >>>>> in gingerbread ttyS changed to ttyO > >>>>> > >>>>> Hedwin > >>>>> > >>>>> > >>>>> On Fri, Jul 15, 2011 at 5:44 PM, Manish Shakya < > >>>>> [email protected]> wrote: > >>>>> > >>>>>> Right now I am trying to move from linux kernel 2.6.32 to 2.6.37 and > >>>>>> use gingerbread 2.3.4. > >>>>>> > >>>>>> With linux kernel 2.6.32, froyo and gb 2.3.3 are working fine. I > used > >>>>>> same uboot arg as in earlier mail. > >>>>>> > >>>>>> On Fri, Jul 15, 2011 at 11:22 AM, hedwin > >>>>>> <[email protected]>wrote: > >>>>>> > >>>>>>> Do you use froyo or gingerbread? > >>>>>>> > >>>>>>> > >>>>>>> > >>>>>>> On Fri, Jul 15, 2011 at 3:57 PM, manish shakya > >>>>>>> <[email protected]>wrote: > >>>>>>> > >>>>>>>> Yes, Both console and android.console is pointing to correct > serial > >>>>>>>> device i.e. ttyS2. > >>>>>>>> > >>>>>>>> My uboot args is > >>>>>>>> > >>>>>>>> console=ttyS2,115200n8 androidboot.console=ttyS2 > root=/dev/mmcblk0p2 > >>>>>>>> rw rootfstype=ext3 rootwait init=/init vram=12M > >>>>>>>> omapfb.mode=dvi:480x272MR-16@60 omapdss.def_disp=lcd43 > >>>>>>>> > >>>>>>>> Isn't this correct? > >>>>>>>> > >>>>>>>> > >>>>>>>> On Fri, Jul 15, 2011 at 5:44 AM, hedwin <[email protected]> > >>>>>>>> wrote: > >>>>>>>> > > >>>>>>>> > Check if console and android.console point to the correct serial > >>>>>>>> device. > >>>>>>>> > Both a kernel parameters sent by u-boot. > >>>>>>>> > > >>>>>>>> > Cheers, > >>>>>>>> > > >>>>>>>> > Hedwin > >>>>>>>> > > >>>>>>>> > On Thu, Jul 14, 2011 at 9:45 PM, Manish Shakya < > >>>>>>>> [email protected]> wrote: > >>>>>>>> >> > >>>>>>>> >> Hi , > >>>>>>>> >> > >>>>>>>> >> I am wondering what are the changes to be made if I have to > make > >>>>>>>> to port rowboat to gumstix overo module. > >>>>>>>> >> > >>>>>>>> >> I did following things but it didn't worked. :-( > >>>>>>>> >> I made change in config file , board-overo.c and also added LCD > >>>>>>>> driver. Compilation went fine with out errors. > >>>>>>>> >> But when I tried to run the image. It show following log and > gets > >>>>>>>> stuck. > >>>>>>>> >> > >>>>>>>> >> 2731240 bytes read > >>>>>>>> >> ## Booting kernel from Legacy Image at 82000000 ... > >>>>>>>> >> Image Name: Linux-2.6.37-g06ebbba > >>>>>>>> >> Image Type: ARM Linux Kernel Image (uncompressed) > >>>>>>>> >> Data Size: 2731176 Bytes = 2.6 MiB > >>>>>>>> >> Load Address: 80008000 > >>>>>>>> >> Entry Point: 80008000 > >>>>>>>> >> Verifying Checksum ... OK > >>>>>>>> >> Loading Kernel Image ... OK > >>>>>>>> >> OK > >>>>>>>> >> > >>>>>>>> >> Starting kernel ... > >>>>>>>> >> > >>>>>>>> >> Uncompressing Linux... done, booting the kernel. > >>>>>>>> >> > >>>>>>>> >> > >>>>>>>> >> -- > >>>>>>>> >> Manish Shakya > >>>>>>>> >> http://www.manishshakya.com.np > >>>>>>>> >> > >>>>>>>> >> -- > >>>>>>>> >> unsubscribe: [email protected] > >>>>>>>> >> website: http://groups.google.com/group/android-porting > >>>>>>>> > > >>>>>>>> > >>>>>>>> > >>>>>>>> > >>>>>>>> -- > >>>>>>>> > >>>>>>>> Manish Shakya > >>>>>>>> http://www.manishshakya.com.np > >>>>>>>> http://secs.oakland.edu/~ganesan/iMX/ > >>>>>>>> > >>>>>>> > >>>>>>> > >>>>>> > >>>>>> > >>>>>> -- > >>>>>> Manish Shakya > >>>>>> http://www.manishshakya.com.np > >>>>>> http://secs.oakland.edu/~ganesan/iMX/ > >>>>>> > >>>>> > >>>>> > >>>> > >>>> > >>>> -- > >>>> Manish Shakya > >>>> http://www.manishshakya.com.np > >>>> http://secs.oakland.edu/~ganesan/iMX/ > >>>> > >>> > >>> > >>> > >>> -- > >>> Manish Shakya > >>> http://www.manishshakya.com.np > >>> http://secs.oakland.edu/~ganesan/iMX/ > >>> > >> > >> > > > > > > -- > > Manish Shakya > > http://www.manishshakya.com.np > > http://secs.oakland.edu/~ganesan/iMX/ > > > > -- > > unsubscribe: [email protected] > > website: http://groups.google.com/group/android-porting > > > -- Manish Shakya http://www.manishshakya.com.np http://secs.oakland.edu/~ganesan/iMX/ -- unsubscribe: [email protected] website: http://groups.google.com/group/android-porting
