Yes, I have and I received the following: In zapata.conf your first two channels should be fxs_ks because the first two modules are FXO mdoules. Your last two channels should be fxo_ks because the second two modules are FXS modules.
For the TDM400P(TDM 22) the FXS modules work with the phone. The 3 port is for the line. So I unplugged it from port 3, and plugged the analog phone in port 1, made the changes to the channels and set immediate=no, restart the server and activated asterisk. Nothing, my friend. Any more suggestions, Ed -----Original Message----- From: [EMAIL PROTECTED] [mailto:[EMAIL PROTECTED] On Behalf Of Francesco Francesconi Sent: Friday, October 06, 2006 10:23 AM To: Asterisk Users Mailing List - Non-Commercial Discussion Subject: Re: [asterisk-users] No Dialtone Did you set immediate=no in zapata.conf? Francesco Eddie Johnson Jr wrote: > > > > Hello, > > > > I have the following setup: > > > > 1. Ubuntu Dapper Server 6.06 plus latest patches > > > > 2. Asterisk 1.2.11 > > > > 3. libpri 1.2.3 > > > > 4. Zaptel 1.2.8 > > > > 5. Digium TDM22 (TDM400P) > > > > 6. Analog phone plugged in port 3 > > > > 7. The wctdm, zaptel modules load at startup, I type asterisk as root and > > it is activated. > > > > 8. I check the Channel Map and I have the following: > > > > > > Channel map: > > > > Channel 01: FXO Kewlstart (Default) (Slaves: 01) > > Channel 02: FXO Kewlstart (Default) (Slaves: 02) > > Channel 03: FXS Kewlstart (Default) (Slaves: 03) > > Channel 04: FXS Kewlstart (Default) (Slaves: 04) > > > > 4 channels configured. > > > > I can ssh into the server and remotely connect to the server. Great! > The card is not connected to an outside line as of yet but I have no > dialtone on the phone. I spoke with a rep. at digium and was told a > dialtone should be there. > > > > Zaptel.conf : > > > > > > loadzone=us > > defaultzone=us > > fxoks=1,2 > > fxsks=3,4 > > > > Zapata.conf: > > > > ;FXS Modules > > signalling=fxo_ks > > channel => 1,2 > > ; > > ;FXO Modules > > signalling=fxs_ks > > channel => 3,4 > > > > I made sure the card is not sharing an IRQ, I checked the hard drive > and all is well. I load zttool and get the following: > > > > cat /proc/zaptel/* > > Span 1: WCTDM/0 "Wildcard TDM400P REV I Board 1" > > > > 1 WCTDM/0/0 > > 2 WCTDM/0/1 > > 3 WCTDM/0/2 > > 4 WCTDM/0/3 > > > > Any suggestions? > > > > Ed > > > > ------------------------------------------------------------------------ > > _______________________________________________ > --Bandwidth and Colocation provided by Easynews.com -- > > asterisk-users mailing list > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users > _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users _______________________________________________ --Bandwidth and Colocation provided by Easynews.com -- asterisk-users mailing list To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
