Throw out the yellow. Check if for sure the other side is using crc4. On Thu, 2004-06-17 at 10:45, Wolfgang Pichler wrote: > Am Do, den 17.06.2004 schrieb Michael Bielicki um 10:32: > > What is in your config file ? > i've already posted my config in my first post - but here is my > /etc/zaptel.conf > -------------------------------- > span=1,1,0,ccs,hdb3,crc4,yellow > span=2,2,0,ccs,hdb3,crc4,yellow > bchan=1-15,17-31 > dchan=16 > bchan=32-46,48-62 > dchan=47 > > loadzone=at > defaultzone=at > -------------------------------- > > and my /etc/asterisk/zaptel.conf > -------------------------------- > [channels] > switchtype = euroisdn > signalling = pri_cpe > pridialplan = local > group = 1 > context = default > channel => 1-15,17-31 > > switchtype = euroisdn > signalling = pri_cpe > pridialplan = local > group = 2 > context=default > channel => 32-46,48-62 > ---------------------------- > > > zaptel.conf ? > > also, check the crc4 settings > which crc4 settings ? - i've thought crc4 could only be turned on or off > ? > > and > > maybe the wire you are using is wrong since some equippment needs > > crossed wires, some needs straight wires. Crossed would be 1-4 2-5 > i've already tried to use crossed wires - didn't worked either > > > > > cheers > > > > Michael > > > > On Thu, 2004-06-17 at 10:28, Wolfgang Pichler wrote: > > > Am Do, den 17.06.2004 schrieb Peter Svensson um 9:43: > > > > On Thu, 17 Jun 2004, Wolfgang Pichler wrote: > > > > > > > > > ... on the card i can see the two leds pulsing red (i think thats the > > > > > yellow alaram - or i am wrong) ? > > > > > > > > Are you sure it is not a red alarm? That would indicate a loss of link. > > > > I think you can check with the command zttool. > > > you are right - its a red alarm - zttool says "Red Alarm/Not Open" > > > > > > > > Are you sure the cables are correct? > > > > Have you set the jumpers on the card to E1 and not left them on T1? > > > The jumpers are on E1 - the cables should be ok (they are working with > > > other hardware) - and the card is directly connected to a simens ULAF+ > > > STU Desktop (can't really find much information about this device on the > > > net) - which turns off a red led when i load the driver and do a ztcfg. > > > > > > > > I think the leds should turn green when the card senses a correct carrier > > > > and framing on the lines. > > > green is always a wounderful color ;-) > > > > > > so, what else could cause this ? > > > > > > wolfgang > > > > > > _______________________________________________ > > > Asterisk-Users mailing list > > > [EMAIL PROTECTED] > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > To UNSUBSCRIBE or update options visit: > > > http://lists.digium.com/mailman/listinfo/asterisk-users > > > > _______________________________________________ > > Asterisk-Users mailing list > > [EMAIL PROTECTED] > > http://lists.digium.com/mailman/listinfo/asterisk-users > > To UNSUBSCRIBE or update options visit: > > http://lists.digium.com/mailman/listinfo/asterisk-users > > _______________________________________________ > Asterisk-Users mailing list > [EMAIL PROTECTED] > http://lists.digium.com/mailman/listinfo/asterisk-users > To UNSUBSCRIBE or update options visit: > http://lists.digium.com/mailman/listinfo/asterisk-users
_______________________________________________ Asterisk-Users mailing list [EMAIL PROTECTED] http://lists.digium.com/mailman/listinfo/asterisk-users To UNSUBSCRIBE or update options visit: http://lists.digium.com/mailman/listinfo/asterisk-users
